• Journal of Mechanical Science and Technology
• /
• 제17권4호
• /
• pp.501-510
• /
• 2003

The spot welded sections of automobiles such as the hat and double hat section members, absorb the most of the energy during the front-end collision. The purpose of this study was to analyze the collapse characteristics of spot welded section members with respect ttl the pitch or spot welds on flanges. through impact experiments and computation for para-closed sections and perfectly closed sections. The hat shaped section members were tested at the impact collapse velocities of 4.72 m/sec, 6.54 m/sec and 7.19 m/sec and double hat shaped section members were tested at the impact collapse velocities of 6.54 m/sec, 7.19 m/sec and 7.27 m/sec. A commercial LS-DYNA3D was used to simulate the collapse behavior of the hat and double hat shaped section members. The validity of the simulation was to be proved by comparing the simulation results and the experimental results.

• 한국기계가공학회지
• /
• 제18권3호
• /
• pp.26-32
• /
• 2019

This study was conducted to analyze the stresses by impact loads on front-end loaders attached to tractors using flexible multi-body dynamics. The model was designed and validated by comparing previous experimental data with the simulation data obtained in this study. Nine sets of conditions were designed using three weights (500, 300, and 100 kg) loaded inside a bucket and three heights (1700, 1350, and 1000 mm) of the bucket from ground level. A parametric study was carried out at five locations for two types of parts of a front-end loader. All the safety factors for the five locations under all conditions were calculated and were greater than 1. Thus, the designs of the front-end loaders were structurally safe. Based on this study, front-end loaders attached to tractors can be designed effectively in terms of cost and safety.

• 대한기계학회논문집B
• /
• 제23권5호
• /
• pp.687-694
• /
• 1999

An experimental study was carried out in two laboratory-scale reactors to investigate the effect of heating rate on the behavior of flame front in a pulverized coal flame. Each. reactors had different heating mechanisms. For reactor A losing large heat through transparent quartz wall. pulverized coal particles were ignited by secondary air of 1050K. Flame front could be visualized through the transparent wall. Reactor B was insulated with castable refractory to minimize the heat loss through the reactor wall and accompanied with secondary air of 573K. Flame front was estimated from the gas temperature and species concentration measured using R-type thermocouple(Pt-Pt/Rh 13%) and gas chromatograph at various coal-air ratios and swirl intensities. The flame front position was closely related with the magnitude of heating rate. The heating rate for lifted flame was of the order of $10^4$ to $10^5K/s$ and for coal Ignition at least over $10^4K/s$. The heating mechanism had little impact on the extinction limits. The weak swirl number of 0.68 forced the flame front to move toward the upstream by the rapid mixing of coal and air. The primary/secondary momentum ratio was an inappropriate variable to distinct the liftoff of flame.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 추계학술대회논문집
• /
• pp.93-96
• /
• 2004

In the case of the front door of the apartment, which functions as an entrance, the study about noise has been less active than corridor type plane in the past, since stair room type plane was generalized. Hence, this study shows the survey about residents' thoughts of noise transmission through the front door, and after researching sound insulation of the present apartments, we figured out what the problem is. Moreover, we did an efficiency test as developing the front door, which increases sound insulation. As a result, it turned out that residents think that the noise transmission through the front door is as serious as floor impact noise, and also, the efficiency of the front door is as poor as STC 22-30. Therefore, in the developed front door, we should improve the efficiency to the level of STCSS. It will be a good way preparing for a demand of residents.

• 한국철도학회논문집
• /
• 제16권5호
• /
• pp.365-371
• /
• 2013

철도차량 전면창유리 충격 시험 및 특성 파악을 위해 유럽 및 국내의 전면창유리 충격 시험 방법을 비교 검토하였다. EN 15152에 따른 고속철도차량의 전면창유리 충격 시험이 가능한 정도인 약 500km/h 속도로 충돌체를 발사할 수 있는 압축 공기식 충격 실험 발사 장치를 설계 및 제작하였으며, 이 발사장치의 충돌체 발사 성능 확인을 위해 속도 보정 실험을 실시하여 압축 공기에 따른 충돌체의 발사 속도 관계식을 도출하였다. 도시철도 및 일반철도에 사용되는 동일한 사양의 전면창유리 시편($1000mm{\times}700mm$)에 제작한 발사 장치를 이용해 충돌 시험을 수행하여 충돌 속도에 따른 시편의 충격 특성을 살펴보았다.

• Steel and Composite Structures
• /
• 제17권6호
• /
• pp.891-906
• /
• 2014

This study aims to present a three dimensional finite element model to investigate the wave propagation in a concrete filled steel tubular column (CFSC) due to transient impact load. Both the concrete and steel are regarded as linear elastic material. The impact load is simulated by a semi sinusoidal impulse. Besides the CFSC models, a concrete column (CC) model is established for comparing under the same loading condition. The propagation characteristics of the transient waves in CFSC are analyzed in detail. The results show that at the intial stage of the wave propagation, the velocity waves in CFSC are almost the same as those in CC before they arrive at the steel tube. When the waves reach the column side, the velocity responses of CFSC are different from those of CC and the difference is more and more obvious as the waves travel down along the column shaft. The travel distance of the wave front in CFSC is farther than that in CC at the same time. For different wave speeds in steel and concrete material, the wave front in CFSC presents an arch shape, the apex of which locates at the center of the column. Differently, the wave front in CC presents a plane surface. Three dimensional effects on top of CFSC are obvious, therefore, the peak value and arrival time of incident wave crests have great difference at different locations in the radial direction. High-frequency waves on the waveforms are observed. The time difference between incident and reflected wave peaks decreases significantly with r/R when r/R < 0.6, however, it almost keeps constant when $r/R{\geq}0.6$. The time duration between incident and reflected waves calculated by 3D FEM is approximately equal to that calculated by 1D wave theory when r/R is about 2/3.

• 한국자동차공학회논문집
• /
• 제20권3호
• /
• pp.126-132
• /
• 2012

Recently, pedestrian protection related research topics have been actively studied by automotive designers and engineers due to the enhanced pedestrian protecting regulations. It is required to design an energy absorbing structure, such as crumple zone that can sufficiently absorb the impact energy to reduce the leg injury when accident happens. The structure is designed by reducing the height of front end module, considering the mounting location, and investigating impact characteristics. In this paper, the concept of the crumple zone was introduced and the role of the crumple zone was investigated by analyzing the performance of upper legform impact to a bonnet leading edge test, and the design process was suggested.

• 한국자동차공학회논문집
• /
• 제11권6호
• /
• pp.205-212
• /
• 2003

This paper may provide a basic design data for the safer car seat mechanism and the quality of the material used by finding out the passenger's dynamic behavior when protected by seat belt during collision. A computer simulation with finite element method is used to accomplish this objective. At first, a detailed geometric model of the seat is constructed using CAD program. The formation of a finite element from a geometric data of the seat is carried out using Hyper-Mesh that is the commercial software for mesh generation and post processing. In addition to seat modeling, the finite element model of seat belt and dummy is formed using the same software. Rear impact analysis is accomplished using Pam-Crash with crash pulse. The part of the recliner and right frame is under big stress in rear crash analysis because the acceleration force is exerted on the back of the seat by dummy. The stress condition of the part of the bracket is checked as well because it is considered as an important variable on the seat design. Front impact model which including dummy and seal belt is analyzed. A Part of anchor buckle of seat frame has high stress distribution because of retraction force due to forward motion of dummy at the moment of collision. On the basis of the analysis result, remodeling and reanalysis works had been repeatedly done until a satisfactory result is obtained.

• 대한기계학회논문집A
• /
• 제25권7호
• /
• pp.1131-1138
• /
• 2001

This paper concerns the crashworthiness of the widely used vehicle structure, the spot welded hat and double hat shaped section members, which are excellent on the point of the energy absorbing capacity and low production cost. The target of this paper is to analyze the energy absorption capacity of the structure against the front-end collision, and to obtain useful information for designing stage. Changing the spot weld pitches on the flanges, the hat and double hat shaped section members were tested on the axial collapse loads in impact velocities of 4.72m/sec, 6.54m/sec, 7.19m/sec and 7.27m/sec. To efficiently review the collapse characteristics of these sections, the simulation have been carried out using explicit FEM package, LS-DYNA3D. The solutions are compared with results from the impact collapse experiments.

• 대한기계학회논문집A
• /
• 제32권1호
• /
• pp.83-90
• /
• 2008

Taekwondo is a martial art form and sport that uses the hands and foot for attack and defense. Taekwondo basic motion is composed of the breaking, competition and poomsea motion. In the side kick among the competition motion, the impact force is larger than other kinds of kicks. The side kick with the front foot can be made in two steps. In the first step, the front foot is stretched forward from back stance free-fighting position. For the second step, the rear foot is followed simultaneously. Then, the kick is executed while entire body weight rests on the rear foot. In this paper, impact analysis of the human model for hitting posture is carried out. The ADAMS/LifeMOD is used in hitting modeling and simulation. The simulation model creates the human model to hit the opponent. As the results, the dynamic analysis of human muscle were presented.