• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.539-542
• /
• 2003

We have studied cell gap-dependent electrode-optic characteristics of the FFS mode using the LC with negative dielectric anisotropy. In case of a small cell gap of 2 ${\mu}m$, the transmittance at the center of pixel and common electrodes is low due to stronger influence of surface anchoring that holds the LC to the initial state than twisting force induced by neighboring LCs. In case of a large cell gap of 4 ${\mu}m$, the influence of surface anchoring force becomes weak so that the LCs at the center of pixel and common electrode can be twisted enough by applied voltage, giving rise to high transmittance. Therefore, we conclude that the light efficiency in the device is dependent on the cell gap.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07a
• /
• pp.439-442
• /
• 2005

In this paper, we propose a cell structure to improve transmittance and aperture ratio with FFS(Fringe Field Switching) mode. As an exemplary cell, we selected conventional FFS cell with dual domain. Optical transmittance and aperture ratio were calculated with 3DFEM numerical solver, TechWiz LCD. The simulation results revealed that transmission increases by more than 10% while aperture ratio increases by more than 4% when compared to conventional FFS mode.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.435-436
• /
• 2007

In general, Single gap transflective FFS display has an in-cell retarder (ICR) between reflective electrode and liquid crystal (LC) layer. Therefore, Operating voltage is highly increased due to this thick dielectric material. But, we also knew the phenomenon that the increasing rate of Vop is different whether the 1st common electrode was composed of plate type or slit type. In this paper, the common electrode in transmissive part was composed of slit type which had less steepness effect of the V op and in reflective part was composed of plate type. The rubbing angle of reflective part can be adjusted properly to match the voltage dependent transmittance and reflectance.

• Transactions on Electrical and Electronic Materials
• /
• v.8 no.3
• /
• pp.135-138
• /
• 2007

In this study, we investigated the electro-optical (EO) characteristic of fringe-field switching (FFS) mode cell by the two kinds of ultraviolet (UV) alignment method on the organic thin film (polyimide: PI). The suitable organic layers for FFS cell and the aligning capabilities of nematic liquid crystal (NLC) using the in-situ photoalignment method were studied; Disclination is observed after conventional photoalignment method for 1h, and in-situ photoalignment method for 1h. Monodomain alignment of the NLC can be observed via insitu photo alignment method for 2 h and 3 h. It is considered that NLC alignment is due to photo-depolymerization of the polymer with oblique non-polarized UV irradiation on PI surface. An unstable V-T curve of UV-aligned FFS-LCD with conventional photoalignment method can be achieved. However, a stable V-T curve of UV-aligned FFS-LCD with in-situ photoalignment method (1 h), and V-T curve of UV-aligned FFS-LCD with in-situ photo alignment method was much stable comparing with that of other UV-aligned FFSLCD's. As a result, more stable EO performance of UV-aligned FFS-LCD with in-situ photoalignment method for 3h is obtained than that of the other UV-aligned FFS-LCD's.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.16 no.6
• /
• pp.542-553
• /
• 2011

A magnetic cable that can safely deliver high frequency AC electric power in flammable or sensitive workplaces by preventing from arcs and electric shocks is firstly proposed in this paper. Several new magnetic cable structures with magnetic shields, which are composed of such cancel coil, cancel copper plate, and cancel copper pipe, were compactly implemented by considering and analyzing fringe field and thus the parallel leakage flux is drastically reduced. The output power and efficiency of a prototype magnetic cable with 1.5 m length and 5 cm gap were measured as 353.8W and 68%, where the source current and switching frequency were 10 $A_{rms}$ and 20 kHz, respectively. The proposed magnetic cables are fully analyzed and verified by finite-element method (FEM) simulations and experiments. The results are in a good agreement.

• Journal of Satellite, Information and Communications
• /
• v.10 no.2
• /
• pp.75-79
• /
• 2015

In this study, we investigated the electro-optical (EO) characteristic of fringe-field switching (FFS) mode cell by the ion beam alignment method on the a-C:H thin film. The suitable inorganic thin films for FFS cell and the aligning capabilities of nematic liquid crystal (NLC) using the new alignment material of a-C:H thin film were studied. An excellent voltage-transmittance (V-T) and response time curve of the ion beam aligned FFS-LCD was observed with oblique ion beam exposure on the a-C:H thin films. Also, the V-T hysteresis characteristics of the ion beam-aligned FFS-LCD with IB exposure on the a-C:H thin films is almost the same as that of the rubbing-aligned FFS cell on a polyimide surface.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.340-343
• /
• 2008

This work reports the simple fabrication of the single cell gap transflective liquid crystal display (LCD) using wire grid polarizer. The nano sized wire grid polarizer was patterned on common electrode itself, on the reflective part of FFS (Fringe field switching) mode whereas the common electrode was unpatterned at transmissive part. However, this structure didn't show single gamma curve, so we further improved the device by patterning the common electrode at transmissive part. As a result, V-T curve of proposed structure shows single gamma curve. Such a device structure is free from in-cell retarder, compensation film and reflector and furthermore it is very thin and easy to fabricate.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.62 no.4
• /
• pp.223-226
• /
• 2013

In this study, we investigated the electro-optical(EO) characteristic of fringe-field switching(FFS) mode cell by the two kinds of ultraviolet(UV) alignment method on the organic thin film(polyimide: PI). The suitable organic layersfor FFS cell and the aligning capabilities of nematic liquid crystal(NLC) using the in-situ photoalignment method were studied Disclination is observed after conventional photoalignment method for 1h, and in-situ photoalignment method for 1h. Monodomain alignment of the NLC can be observed via in-situ photoalignment method for 2h and 3h. It is considered that NLC alignment is due to photo-depolymerization of the polymer with oblique non-polarized UV irradiation on PI surface. An unstable V-T curve of UV-aligned FFS-LCD with conventional photoalignment method can be achieved. However, a stable V-T curve of UV-aligned FFS-LCD with in-situ photoalignment method(1h), and V-T curve of UV-aligned FFS-LCD with in-situphotoalignment method was much stable comparing with that of other UV-aligned FFS-LCD's. As a result, more stable EO performanceof UV-aligned FFS-LCD with in-situphotoalignment method for 3h is obtained than that of the other UV-aligned FFS-LCD's.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.186-186
• /
• 2009

Most liquid crystal display modes, including the twisted nematic (TN) $mode^1$, the in-plane switching (IPS) $mode^2$, the fringe field switching (FFS) $mode^3$, and the vertically aligned (VA) $mode^4$ are based on either a horizontal or a vertical alignment. However, for some applications, such as no-bias-bend (NBB) pi cell or bistable bend-splay display, an intermediate pretilt angle is essential$^5$. NBB pi cells have been a focus of interest because of their fast response time; however, the reliable control of the intermediate pretilt angle of liquid crystals that is required for the fabrication of NBB pi cells is challenging. The controllable pre-tilt angle of liquid crystals was investigated using a blend of horizontal and vertical polyimide prepared by a rubbing method. Various pretilt angles in the range from 0^{\circ}$ to 90^{\circ}$ were achieved as a function of the vertical polyimide content. We observed uniform liquid crystal alignment on the rubbing-treated blended polyimide layer. A NBB pi cell with an intermediate pretilt angle of 47.8^{\circ}$ was manufactured. This cell had no initial bias voltage and a low threshold voltage, which indicates that it has low power consumption. In addition, the response time of the NBB pi cell was rapid.