• Composites Research
• /
• 제28권4호
• /
• pp.244-248
• /
• 2015

When a small gear rotates at a very high speed over 40,000 rpm, frictional heat is generated on the gear surfaces. Thermal deformations and stresses arising from frictional heat may lower the efficiency and fatigue life of the high-speed gear. Especially, such frictional heat has much stronger effects on the performance of millimeter-sized high-speed gears used for surgical and dental hand-pieces, due to a small surface area. An analytical equation was derived to calculate frictional temperature on a mating gear surface and conduction heat transfer analysis was performed. Thermal deformation and contact stresses were then calculated using FEM for gears used for medical hand-pieces. The contact stresses of the meshed gear and pinion increase by 19.4% and 16.4%, respectively, when the frictional thermal deformations are considered.

• Structural Engineering and Mechanics
• /
• 제60권2호
• /
• pp.175-191
• /
• 2016

The present article is aimed at an investigation of stresses produced in a microstretch elastic half-space due to a moving load. The expressions of normal stress, shear stress and tangential couple stress produced in this case have been obtained in closed form. To find the displacement fields the perturbation method is applied. Significant effect of moving load on variation of stresses developed at different depths below the surface due to the depth of substrate and frictional coefficient of the rough surface of the medium has been observed. The effects of different shapes of irregularity and depth of irregularity on normal, shear and tangential couple stresses have been discussed. Some particular cases have also been deduced from the present investigation. Finally, the analytical developments have been illustrated numerically for aluminium-epoxy-like material substrate under the action of moving load.

• Journal of Ship and Ocean Technology
• /
• 제1권1호
• /
• pp.35-47
• /
• 1997

The consequences associated with ships running aground depend very much on the soil characteristics of the sea bed and the geometrical shape of the ship bow. The penetration into the sea bed depends on these factors and the penetration is an important factor for the ship motion because it influences the ship heave and pitch motions as well as the friction between the ship and the soil. In this paper a rational calculation model is presented for the sea bed soil reaction forces on the ship bottom. The model is based on the assumption that the penetration of the ship bow generates a flow of pore water through the grain skeleton of the soil. The flow is governed by Darcy\`s law and it is driven by the pressure of the pore water at the bow. In addition to this pore water pressure, the bow is subjected to the effective stresses in the grain skeleton at the bow surface. These stresses are determined by the theory of frictional soils in rupture. Frictional stresses on the bow surface are assumed to be related to the normal pressure by a simple Coulomb relation. The total soil reaction as a function of velocity and penetration is found by integration of normal pressure and frictional stresses over the surface of the bow. The analysis procedure is implemented in a computer program for time domain rigid body analysis of ships running aground and it is verified in the paper through a comparison of calculated stopping lengths, effective coefficients of friction, and sea bed penetrations with corresponding experimental results obtained by model tests as well as large, scale tests.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1994년도 봄 학술발표회 논문집
• /
• pp.33-37
• /
• 1994

When a bolt is tightened up to the range of plastic deformation, yielding is governed by the combined stresses due to the axial force developed in the bolt and the frictional torque developed on the thread in contact with the nut. Consideration is taken account of the fact that the unused portion of the thread has least sectional area being subject to initial yielding. Once yielding has taken place some strain hardening effect will result, Incremental stress-strain relations are used to treat the continued yielding, which is equivalent to treat continued yielding as if summing up the effects of thin walled cylinders subject to plastic deformation. M10 bolts of common and fine series thread are used for computational purposes. Variation of axial forces and frictional torques vs. the frictional coefficients tare presented together with other plots showing some characteristics of bolt under plastic deformation.

• 한국지반환경공학회 논문집
• /
• 제14권10호
• /
• pp.17-27
• /
• 2013

This paper explores stress release induced by unloading in dry sand. A series of model tests were carried out to measure stresses developed in testing sand during loading and those released during unloading for different boundary conditions. It was found that stress in the sand increased linearly with applied load. At the onset of unloading, almost no stress release was observed. Significant stress release took place when the shear stress in the sand induced by unloading exceeded the frictional resistance and caused movement of sand particles. The initiation and the magnitude of stress release depend on the stress condition prior to unloading, the decrease of external load, and also the frictional resistance in sand. A new conceptual stress-release model was next developed based on the model test results by considering the fundamental frictional behavior of granular materials.

• 한국도로학회논문집
• /
• 제14권3호
• /
• pp.41-48
• /
• 2012

본 연구에서는 교량기초 말뚝의 부주면마찰력 시험을 통하여 연약지반에 타설된 강관말뚝의 부주면마찰력을 측정하였으며 장기적인 마찰응력의 관측시험을 통하여 경제적인 상부구조물 시공시기를 판단하였다. 본 연구의 결론은 다음과 같다. (1) 연약지반에서 부마착력의 크기는 침하속도가 클수록 크게 나타났다. (2) 마찰력의 관계 그래프에서 마찰응력의 증감이 없는 시기를 확인하여 상부구조물 시공시기를 판단할 수 있었다. (3) 말뚝정재하시험결과와 부주면마찰력 시험결과를 비교해 본 결과 항타 직후의 부주면마찰력은 재하시험 시의 마찰응력보다 크게 나오는 것으로 판단되며 15일 경과후의 측정값은 비슷하게 나오는 것으로 판단되었고, 이론식에 의한 결과와도 비슷하였다. (4) 부주면마찰력의 장기관측기법을 사용하면 부주면마찰력이 발생하고 있는 중이라도 적절한 상부구조물의 시공시기를 파악할 수 있어 경제적인 시공관리가 가능한 것으로 판단된다.

• 한국지반공학회지:지반
• /
• 제14권6호
• /
• pp.139-151
• /
• 1998

SI 앵커는 지반개량 앵커를 의미한다. 이는 앵커를 지지하는 지반을 JSP로 개량한 것으로, SI 앵커체는 80cm 정도의 직경을 가지게 된다. SI 앵커는 앵커체와 지반사이의 마찰저항력과 앵커체 앞면의 지압저항력으로 인해 높은 인발저항력을 발휘하게 되는데, 특히 마찰저항력은 JSP로 개량된 앵커체의 직경의 증대로 인해 상당히 증가하게 된다. 본 연구에서는 SI 앵커의 인발저항기구를 분석하기 위해 실내 모형실험과 현장실험을 실시하였다. 공기건조 모래지반 내에서의 실내 모형실험을 통해 SI 앵커 주변지반의 변형률장을 분석하였는데, 이는 토조 벽면에 설치된 라텍스 멤브레인을 이용한 사진 분석법을 통해 이루어 졌다. 10매의 변형률게이지가 부착된 특수 설계된 PVC 파이프를 앵커체 내에 설치하고 변형률을 측정하여 현장실험의 결과를 분석하였는데, 역시 실내 모형실험과 같이 앵커체 내에서의 변형률을 측정하였다.

• 전산구조공학
• /
• 제7권3호
• /
• pp.133-141
• /
• 1994

강도활용을 극대화한 볼트의 소성역체결시 볼트의 항복은 볼트에 발생한 인장응력과 너트 나사산과의 접촉면에서 오는 마찰토오크에 의한 전단응력과의 조합에 의한 영향을 받는다. 볼트는 최소단면적인 나사부중 너트와 물리지 않은 여우나사부에서 먼저 항복을 일으킨다. 볼트재료는 대체로 항복과 더불어 소성경화를 보이며 그 정도는 고강도재료에서 인장강도의 10%정도이다. 본 연구에서는 소성역체결시의 거동해석을 변형도증분이론에 의거 해석하였다. 항복은 최소단명이 원통의 표면에서 시작되며 이를 두께가 얇은 원통으로 취급하였다. 항복의 전파는 이들 얇은 원통이 체결이 진행됨에 따라 순차적으로 항복에 이르는 것으로 보고 이 얇은 원통들을 항복시키는데 필요한 축력과 토오크를 합하여 체결종료시의 볼트축력과 (나사면마찰) 토오크로 하였다. M10미터 가는 나사를 계산과 실험에 사용하였다. 축력과 마찰토오크의 마찰계수에 대한 변화관계를 보여주는 그래프와 더불어 실험에서 사용한 볼트의 설계보조 선도를 제시하였다. 이 설계보조용 선도는 실험실에서 얻어진 토오크계수와 마찰계수와의 관계를 그린 것으로 윤활, 포면처리등 현장조건에 따라 달라진 마찰계수를 적절히 취급하는데 효과적으로 활용이 가능하다.

• Structural Engineering and Mechanics
• /
• 제36권1호
• /
• pp.95-110
• /
• 2010

Two-dimensional elastic contact problems, including normal, tangential, and rolling contacts, are treated with the finite element method in this study. Stress boundary conditions and kinematic conditions are transformed into multiple point constraints for nodal displacements in the finite element method. Upon imposing these constraints into the finite element system equations, the calculated nodal stresses and nodal displacements satisfy stress and displacement contact conditions exactly. Frictional and frictionless contacts between elastically identical as well as elastically dissimilar materials are treated in this study. The contact lengths, sizes of slip and stick regions, the normal and the shear stresses can be found.

• 한국공작기계학회논문집
• /
• 제17권3호
• /
• pp.101-107
• /
• 2008

A composite mechanics for discontinuous fiber reinforced polymer matrix composites(PMC) is analysed in order to predict fiber axial stresses. In continuum approach. frictional slip which usually takes place between fibers and polymers is accounted to derive PMC equations. The interfacial friction stress is treated by the product of the coefficient of friction and the compressive stress norma1 to the fiber/matrix interface. The residual stress and the Poisson's contraction implemented by the rule of mixture(ROM) are considered for the compressive stress normal to the fiber/matrix interface. In addition. the effects of fiber aspect ratio and fiber volume fraction on fiber axial stresses are evaluated using the derived equations. Results are illustrated numerically using the present equations with reasonable materials data. It is found that the fiber axial stress in the center region shows no great discrepancy for different fiber aspect ratios and fiber volume fractions while some discrepancies are shown in the fiber end region.