• 대한기계학회논문집
• /
• 제19권1호
• /
• pp.240-250
• /
• 1995

A CPM (computational preston tube method) was developed to measure wall shear stress in a transitional boundary layer on a flat plate using Preston tubes. Correlation for the displacement factor of Preston tubes was improved for a CPM to be used in the transitional boundary layer. The distribution of skin-friction coefficient was reasonably predicted in the uniform free stream of 3.1% turbulence intensity. Reasonable and accurate estimation of displacement factor of Preston tubes was found to be of crucial importance for the CPM, especially in the laminar boundary layer. The mean velocity profiles of the boundary layer on the plate were also measured and presented.

• Tribology and Lubricants
• /
• 제16권5호
• /
• pp.373-380
• /
• 2000

Finite element analysis is performed on the subsurface crack propagation in brittle materials due to sliding contact. The sliding contact is simulated by a rigid asperity moving across the surface of an elastic half-surface containing single and multiple cracks. The single crack, coplanar cracks and parallel cracks are modeled to investigate the interaction effects on the crack growth in contact fatigue. The crack location is fixed and the friction coefficients between asperity and half-space are varied to analyze the effect of surface friction on stress intensity factor for horizontal cracks. The crack propagation direction is predicted based on the maximum range of shear and tensile stress intensity factors. With a coplanar crack, the stress intensity factor was increased. However, with a parallel crack, the stress intensity factor was decreased. These results indicate that the interaction of a coplanar crack increases fatigue crack propagation, whereas that of a parallel crack decreases it.

• 한국콘텐츠학회논문지
• /
• 제15권2호
• /
• pp.499-506
• /
• 2015

마찰속도란 벽면 가까이의 흐름에서 벽면의 마찰 응력과 밀도로 정의되는 속도의 차원을 갖는 양이다. 또한 마찰속도는 바닥 흐름에서 전단력을 나타내는 수리학적 매개변수이다. 게다가 개수로 설계나 하천, 해안에서 유사 및 물질의 거동을 파악하는데 정확한 마찰속도의 산정이 매우 중요하며 주 흐름방향의 혼합계수를 결정하는데 필수적인 요소이다. 이러한 마찰속도를 산정하는 방법들은 하상경사를 이용하는 방법, 레이놀즈 응력분포를 이용하는 방법, 점성저층에서 평균유속의 선형법칙을 이용하는 방법, 벽 전단 응력의 직접적 측정방법 등이 있다. 본 연구에서는 기존 방법과 달리 확률통계 기법에 사용되는 엔트로피 개념에 접목하여 새로운 마찰속도공식을 제안하였고, 이를 검증하기 위해 Song의 실측 실험데이터를 이용하였다. 제안한 공식과 마찰속도 공식에 의해 산정된 마찰속도의 결정계수는 0.999-1.000로 잘 일치한 것으로 분석되었다.

• 대한기계학회논문집A
• /
• 제26권7호
• /
• pp.1340-1347
• /
• 2002

Finite element simulations are being widely used to increase the efficiency and effectiveness of design of bulk metal forming processes. In such simulations, proper consideration of friction condition is crucial in obtaining reliable results. For this purpose, tip test based on backward extrusion was proposed recently. In this lest, a cylindrical billet is positioned in a shallow groove of a counter punch for centering purpose and formation of a radial tip is induced on the extruded end of the workpiece. In this study, the effect of centering groove on tip test was investigated. The quantitative ratio of the shear friction factors between the punch and die was numerically determined depending on the shape of centering groove. Also, surface expansion and pressure distribution along the punch and die were considered in order to better understand the reason that friction condition at the punch compared to the one of die was more severe.

• Geomechanics and Engineering
• /
• 제12권2호
• /
• pp.211-221
• /
• 2017

A laboratory investigation into crude oil contaminated sand-concrete interface behavior is performed. The interface tests were carried out through a direct shear apparatus. Pure sand and sand-bentonite mixture with different crude oil contents and three concrete surfaces of different textures (smooth, semi-rough, and rough) were examined. The experimental results showed that the concrete surface texture is an effective factor in soil-concrete interface shear strength. The interface shear strength of the rough concrete surface was found higher than smooth and semi-rough concrete surfaces. In addition to the texture, the normal stress and the crude oil content also play important roles in interface shear strength. Moreover, the friction angle decreases with increasing crude oil content due to increase of oil concentration in soil and it increases with increasing interface roughness.

• 콘크리트학회논문집
• /
• 제28권2호
• /
• pp.167-176
• /
• 2016

이 연구는 다양한 콘크리트에 대해 전단마찰 거동에 의해 지배되는 부재에서 전단전달 기구를 설명하고 합리적인 전단마찰내력을 평가하기 위한 모델을 제안하였다. 제안된 모델의 기본식은 횡보강근과 작용 축응력을 고려하여 소성론의 상계치 이론(Upper-bound theorem)에 기반하여 유도하였다. 콘크리트는 수정 Coulomb 파괴 기준에 의해 완전한 소성 강체로 고려하였다. 콘크리트 유효강도에서 콘크리트 종류와 최대 골재 크기에 따른 영향을 적용하기 위해 Yang et al.의 압축 응력-변형률 모델과 CEB-FIP의 인장 응력-변형률 모델을 적용하였다. 이 응력-변형률 모델들을 이용한 완전 소성모델로의 변환을 통하여 유효압축강도계수, 유효강도비 그리고 콘크리트 마찰각을 간단한 식으로 일반화 하였다. 제시된 전단마찰내력 모델은 기존 연구에서 제시된 모델과 함께 91개의 직접전단 실험결과와 비교하였다. 그 결과로 이 연구에서 제시된 모델은 콘크리트 종류, 횡보강근 양 그리고 작용 축응력을 고려하여 전단마찰내력을 평가할 수 있었으며, 예측값에 대한 실험값의 비의 평균과 표준편차가 각각 0.95, 0.15로서 기존 식들에 비해 더 정확한 결과를 얻을 수 있었다.

• 소성∙가공
• /
• 제32권4호
• /
• pp.215-220
• /
• 2023

In this study, the correction process of stress-strain curves obtained from hot compression test is introduced since the barreling induced by friction and adiabatic heat generation induced by plastic work occur under high strain rate. A shear friction factor was quantitatively estimated by measuring the dimension of barreling and temperature rise due to adiabatic heat generation was directly measured during compression test. Thereafter, the stress-strain curves were re-evaluated by introducing several equations to correct the effects of the friction and temperature rise. It was found that adiabatic factor at strain rate of 10/s is in the range of about 0.5 to 0.75 for Nimonic 80A and decreases as the assigned temperature increases.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2002년도 봄 학술발표회 논문집
• /
• pp.501-508
• /
• 2002

The percentage of a mountainous district in our country is comparatively high but the concern for rock mass has been disregarded for a long time. Especially for rock slope, the most important factors are geometric characteristics and their shear strength parameter. In this paper, parametric studies are performed using the distinct element computer program UDEC-BB for rock slopes. Parameters adopted in this paper are joint angle, spacing, persistence, aperture and shear strength parameters (JRC, JCS, basic friction angle). To estimate slope stability, shear strength reduction method is used. The most important factors affecting rock slope stability are joint angle and spacing. The relationship between average displacement calculated by UDEC-BB and safe factor by shear strength reduction method is researched.

• Design & Manufacturing
• /
• 제8권2호
• /
• pp.30-36
• /
• 2014

In this study, surface deformation patterns have been investigated by the rigid-plastic finite element method for friction factor test in solid cylinder compression process. AA1100 and AA6063 aluminum alloys, which show different work hardening characteristics respectively, have been adopted as model materials used for analysis. The main objective of this study is to provide the deformation mechanics in detail in solid cylinder compression process, especially at the die/workpiece interface that is closely related with the frictional conditions. For this reason, solid cylinder compression process has been numerically analyzed. The surface flow patterns at the contact boundary have been analyzed in terms of surface expansion, surface expansion velocity, pressure distributions exerted on the die surface along the die surface. By defining bulge factor, barreling phenomenon also have been examined with calibration curves to verify their effects on the surface flow pattern that is important for evaluating the frictional condition at the interface.

• 지질공학
• /
• 제19권2호
• /
• pp.177-189
• /
• 2009

이 연구는 토질역학에서 중요하게 취급되는 전단강도를 몇 가지 토질물성만으로 쉽게 산정할 수 있도록 통계적인 방법의 하나인 선형회귀분석법을 이용하여 전단강도산정모델을 개발하였다. 전단강도는 강도정수인 전단저항각(${\phi}$)과 점착력(c)으로 구분되므로 SPSS의 상관분석을 통해 토질시험 결과들 중 이들 강도정수에 유효한 토질인자를 선별한 후 선별된 인자들과의 관계를 선형회귀분석으로 공식화 하였다. 또한, 개발된 모델과 직접전단시험으로 구한 강도정수를 비교분석하여 모델의 적합성을 검증하였다. 여러 토질물성과 강도정수간의 상관관계를 분석한 결과 전단저항각에 가장 크게 영향을 미치는 토질인자는 간극비 및 건조단위중량이고, 점착력에 크게 유의한 토질인자는 간극비, 건조단위중량 및 소성지수인 것으로 나타났다. 한편, 전단강도산정모델에 의해 산정된 강도정수는 직접전단시험에 의해 구한 강도정수와 거의 유사한 결과를 보였다. 따라서 개발된 전단강도산정모델은 연구지역과 같은 토질조건인 경우 토층의 강도정수 산정을 위한 모델로 이용이 가능할 것으로 사료된다.