• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.362-363
• /
• 2006

In this study, the filter was designed for tuning center frequency and fabricated using ($Sr,Ba)TiO_3$ ferroelectrics and $YBa_2CuO_7$ high temperature superconductor thin film. The best result in figure of merit was 35 when the $Ba_{0.5}Sr_{0.5}TiO_3$ thin film deposition temperature was $600^{\circ}C$, the post anneal condition was $600^{\circ}C$, 10min in 1atm, $O_2$. When using $20{\mu}m$ IDC pattern gap. The higher tunability was obtained than using $30{\mu}m$ pattern gap.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.68 no.2
• /
• pp.304-309
• /
• 2019

This paper presents a CMOS RF-to-DC converter for video surveillance disposable IoT applications. It widely harvests RF energy of 3G/4G cellular low-band frequency range by employing a tunable impedance matching network. The proposed converter consists of the differential-drive cross-coupled rectifier and the matching network with a 4-bit capacitor array. The proposed converter is designed using 130-nm standard CMOS process. The designed energy harvester can rectify the RF signals from 700 MHz to 900 MHz. It has a peak RF-to-DC conversion efficiency of 72.25%, 64.97%, and 66.28% at 700 MHz, 800 MHz, and 900 MHz with a load resistance of 10kΩ, respectively.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.1
• /
• pp.1-7
• /
• 2016

In this paper, the tunable filter based on high power cavity using mechanical switch for 1.5 GHz band is presented. The LPF is inserted to eliminate the spurious wave, coupler is embeded to extract the output power, and then the tunable filter system is configured using mechanical switch. The LPF obtains attenuation over 40 dB between 4 GHz and 12.75 GHz, Coupler is satisfied with coupling value 40 dB and coupling isolation over 55 dB. The tunable filter system using mechanical switch obtains insertion loss 0.88 dB at bypass mode between 1,495.9 MHz and 1,510. 9 MHz, 3.29 dB at fil mode between 1,495.9 MHz and 1,500.9 MHz. It is also satisfied with output power of 132 W at the center frequency 1,498.4 MHz, and switching time below 10 ms.

• 한국정보통신설비학회:학술대회논문집
• /
• 2007.08a
• /
• pp.3-6
• /
• 2007

In this paper, a hybrid dual band LNA(Low Noise Amplifier) with a tunable matching circuit using varactor is designed for 433MHz and 912MHz RFID reader. The operating frequency is controlled by the bias voltage applied to the varactor. The measured results demonstrate that S21 parameter is 16.01dB and 10.72dB at 433MHz and 912MHz, respectively with a power consumption of 19.36mW. The S11 are -11.88dB and -3.31dB, the S22 are -11.18dB and -15.02dB at the same frequencies. The measured NF (Noise Figure) is 15.96dB and 7.21dB at 433MHz and 912MHz, respectively. The NF had poorer performance than the simulation results. The reason for this discrepancy was thought that the input matching is not performed exactly and a varactor in the input matching circuit degrades the NF characteristics.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.6
• /
• pp.1196-1200
• /
• 2009

This paper proposed a tunable band pass filter. It is two-poles direct capacitive coupled resonator band pass filter which the capacitors of parallel resonators are changed by varactor diodes. The DC bias controls to change the value of capacitance in the parallel resonator for tunning the pass band. To validate the proposed design method, we fabricated the band pass filter which has tunable center frequency from 200MHz to 245MHz.

• 한국정보통신설비학회:학술대회논문집
• /
• 2004.08a
• /
• pp.11-14
• /
• 2004

In this paper, a novel tunable bandpass filter using tunable series inductors and MEMS switches for wireless LAN applications was proposed. The proposed tunable filter was fabricated using a micromachining technology and performances of the fabricated filter were estimated. The filter consists of spiral inductors, MIM capacitors and direct-contact type MEMS switches, and its frequency tunability is achieved by changing the inductance that is induced by ON/OFF actuations of the MEMS switches. The actuation voltage of the MEMS switches was 58 V, and the measured center frequencies were 2.55 GHz and 5.1 GHz, respectively. The passband insertion loss and 3-dB bandwidth were 4.2 dB and 22.5 % at 2.55 GHz, and 5.2 dB and 23.5 % at 5.1 GHz, respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07b
• /
• pp.719-722
• /
• 2003

Ferroelectric $Pb(Zr_{1-x}Ti_x)O_3$ (PZT) films were deposited on (001) MgO single crystals using sol-gel method. Structural properties and surface morphologies of PZT films were investigated using an X-ray diffractometer and a scanning electron microscopy, respectively. The dielectric properties of PZT films were investigated with the dc bias field using interdigitated capacitors (IDC) which were fabricated on PZT films using a thick metal layer by photolithography and dry etching process. The small signal dielectric properties of PZT films were calculated by a modified conformal mapping method with low and high frequency data, such as capacitance measured by an impedance gain/phase analyzer at 100 kHz and reflection coefficient (S-parameter) measured by a HP 8510C vector network analyzer at 1 -20 GHz. The IDC on PZT films exhibited about 67% of capacitance change with an electric field of 135 kV/cm at 10 GHz. These PZT thin films can be applied to tunable microwave devices such as phase shifters, tunable resonators and tunable filters.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.4 no.4
• /
• pp.300-306
• /
• 2004

This paper reports a novel tunable bandpass filter using two-state switched inductor with direct-contact MEMS switches for wireless LAN applications. In our filter configuration, the switched inductor is implemented to obtain more stable and much larger frequency tuning ratio compared with variable capacitor-based tunable filter. The proposed tunable filter was fabricated using a micromachining technology and electrical performances of the fabricated filter were measured. The filter consists of spiral inductors, MIM capacitors and direct-contact type MEMS switches, and its frequency tunability is achieved by changing the inductance that is induced by ON/OFF actuations of the MEMS switches. The actuation voltage of the MEMS switches was measured of 58 V, and they showed the insertion loss of 0.1 dB and isolation of 26.3 dB at 2 GHz, respectively. The measured center frequencies of the fabricated filter were 2.55 GHz and 5.1 GHz, respectively. The passband insertion loss and 3-dB bandwidth were 4.2 dB and 22.5 % at 2.55 GHz, and 5.2 dB and 23.5 % at 5.1 GHz, respectively.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.1337-1341
• /
• 2003

This paper suggests and demonstrates a novel flow measurement technique, tunable AC mode hotwire anemometry that allows simple integration, robust measurement, and extremely high accuracy. The principle and simple theoretical analysis of the technique are shown. To find the optimal frequency at which the phase lag becomes most sensitive to flow speed change, the phase lag was measured scanning the heating frequency from 1 to 100 Hz, while the flow speed of ethanol was increased stepwise from 0 to 10 mm/s. To optimize the sensitivity of technique, the periodic thermal characteristic of the hotwire should be understood and is currently under study.

• Proceedings of the Optical Society of Korea Conference
• /
• 2003.02a
• /
• pp.156-157
• /
• 2003

The wavelength converter is considered to be a key element of future dense WDM optical networks. It enables wavelength reuse and resolves contention problem. Moreover, the tunability of the wavelength converter enhance the flexibility of network systems by facilitating reconfigurable dynamic wavelength routing. In order to achieve optically tunable wavelength conversion, we recently proposed and experimentally demonstrated wavelength conversion and tuning based on cascaded sum and difference frequency generation in a Ti：PPLN channel waveguide. (omitted)