• Bulletin of the Korean Chemical Society
• /
• v.7 no.4
• /
• pp.267-271
• /
• 1986

The ionomeric blend and the ionic aggregation studies by using a Fourier-transform infrared spectroscopy(FT-IR) are presented. Two ionomers were prepared, one is barium polyacrylate and the other is barium polystyrenesulfonate. The blend of the two ionomers of the barium salts shows intermolecular ionic interaction between the carboxylated ionomer and the sulfonated ionomer. This interaction leads to considerable differences between the spectrum of the blend and the sum of the spectra of the pure ionomers. From our results, it is shown that ionic interactions must play an important role in the compatibility of the two ionomers. In the ionic aggregation study, the bands due to asymmetric stretching mode of carboxylate anion(COO-) in the carboxylated ionomer and the ionomer blend increase in intensity with increasing the divalent barium cations. These results indicate the formation of ion pairs. The doublet due to the asymmetric stretching modes of the carboxylate anion(COO-) is concerned with a sort of local structure found in the ion aggregation. By considering a possible structure for multiplets in the blend, the spectral splitting and the frequency shift are well explained.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.16 no.1
• /
• pp.1-9
• /
• 1996

Many signal-processing techniques have been found to be useful in ultrasonic and nondestructive evaluation. Among the most popular techniques are signal averaging, spatial compounding, matched filters and homomorphic processing. One of the significant new process is split-spectrum processing(SSP), which can be equally useful in signal-to-noise ratio(SNR) improvement and grain characterization in several specimens. The purpose of this paper is to explore the utility of SSP in ultrasonic NDE. A wide variety of engineering problems are reviewed, and suggestions for implementation of the technique are provided. SSP uses the frequency-dependent response of the interfering coherent noise produced by unresolvable scatters in the resolution range cell of a transducer. It is implemented by splitting the frequency spectrum of the received signal by using gaussian bandpass filter. The theoretical basis for the potential of SSP for grain characterization in SUS 304 material is discussed, and some experimental evidence for the feasibility of the approach is presented. Results of SNR enhancement in signals obtained from real four samples of SUS 304. The influence of various processing parameters on the performance of the processing technique is also discussed. The minimization algorithm, which provides an excellent SNR enhancement when used either in conjunction with other SSP algorithms like polarity-check or by itself, is also presented.

• Computers and Concrete
• /
• v.8 no.5
• /
• pp.563-581
• /
• 2011

The signal-based acoustic emission (AE) characterization of concrete fracture process utilizing home-programmed AE monitoring system was performed for three kinds of static loading tests (Cubic-splitting, Direct-shear and Pull-out). Each test was carried out to induce a distinct fracture mode of concrete. Apart from monitoring and recording the corresponding fracture process of concrete, various methods were utilized to distinguish the characteristics of detected AE waveform to interpret the information of fracture behavior of AE sources (i.e. micro-cracks of concrete). Further, more signal-based characters of AE in different stages were analyzed and compared in this study. This research focused on the relationship between AE signal characteristics and fracture processes of concrete. Thereafter, the mode of concrete fracture could be represented in terms of AE signal characteristics. By using cement-based piezoelectric composite sensors, the AE signals could be detected and collected with better sensitivity and minimized waveform distortion, which made the characterization of AE during concrete fracture process feasible. The continuous wavelet analysis technique was employed to analyze the wave-front of AE and figure out the frequency region of the P-wave & S-wave. Defined RA (rising amplitude), AF (average frequency) and P-wave & S-wave importance index were also introduced to study the characters of AE from concrete fracture. It was found that the characters of AE signals detected during monitoring could be used as an indication of the cracking behavior of concrete.

• The KIPS Transactions:PartC
• /
• v.9C no.3
• /
• pp.439-444
• /
• 2002

In this paper, we present both the link budget analysis according to system parameters and the cell coverage according to transmitter power and modulation scheme of digital MMDS among the wireless CATV system methods which is bated on the wireless internet service. Also, in this paper, we present C/I and number of subscriber according to splitting cell. In this paper, the cell coverage of which obtain the results according to both transmitter power from 0dBW to -9dBW and modulation scheme of QPSK, 16QAM and 64QAM based on link budget was analysis for system parameter of digital MMDS was able to provide from maximum 134km to minimum 4.3km. Also, in this paper, the number of subscriber of which obtain the results according to polarization wave, frequency of frequency reuse and C/I in 4. 6 and 8 sectors was able to provide from maximum 5,200DSI to minimum 1,300DSI.

• 한국초전도학회:학술대회논문집
• /
• v.10
• /
• pp.65-65
• /
• 2000

Microwave response of intrinsic Josephson junctions in mesa structure formed on HgI2-intercalated Bi2Sr2CaCu2O8+x single crystals was studied in a wide range of microwave frequency. With irradiation of 73${\sim}$76 GHz microwave, the supercurrent branch becomes resistive above a certain onset microwave power. At low current bias, the current-voltage characteristics show linear behavior, while at high current bias, the resistive branch splits into multiple sub-branches. The voltage spacing between neighboring sub-branches increase with the microwave power and the total number of sub-branches is almost identical to the number of intrinsic Josephson junctions in the mesa. All the experimental results suggest that each sub-branch represents a specific mode of collective motion of Josephson vortices generated by the microwave irradiation. With irradiation of microwave of microwave of frequency lower than 20 GHz, on the other hand, no branch splitting was observed and the current-voltage characteristics exhibited complex behavior at hlgh blas currents. This result can be explained in terms of incoherent motion of Josephson vortices generated by non-uniform microwave irradiation.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.23 no.4
• /
• pp.1072-1086
• /
• 1998

Transform, subband, and wavelet transform decompositions are powerful linear transformation tools in image coding because of their decorrelating effects on image pixels, the concentration of energy in a few coefficients, their multirat/multiresolution framework, and their frequency splitting, which allows for efficient coding matched to the statistics of each frequency band and to the characteristics of the human visulal system. Thus, a growingbody of research has bee performed to extend these tools in various kinds of modified formations. Hence, in this paper, an overall survey to achieve a general view on these transformation tools have been attempted. Starting from basic tools such as orthogonal transforms, lapped transforms, QMF(quadrature mirror filter) subband filter banks, and wavelet transforms, their hierarchical extensions, vector extensions, and linear time-varying extensions are investugated in detail.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.4A
• /
• pp.378-383
• /
• 2004

Orthogonal Frequency Division Multiplexing (OFDM) transmits high-speed data by splitting the transmission bandwidth into a number of subcarriers. The bandwidth of each subcarrier is ensured to be smaller than the coherence bandwidth. This paper presents an OFDM system incorporated with the Carrier Interferometry (CI) codes to improve the performance by enhancing frequency diversity effect. The performances of CI-OFDM with multilevel modulations are investigated in highly dispersive fading channels. For the investigation of performance improvement of CI-OFDM, a simulator has been developed using a well-known SPW simulation platform. The simulation results show that the CI-OFDM provides both performance improvement and robustness against dispersive fading channel behavior. The performance of CI-OFBM with multilevel modulations demonstrates that CI-OFDM outperforms a traditional OFDM system, particularly in highly dispersive channels. With a relatively large delay spread of 151㎱ compared to the guard interval of 800㎱, CI-OFDM provides a BER of 10$^{-3}$ if sufficient signal power is present.

• Journal of the Korean Magnetics Society
• /
• v.9 no.1
• /
• pp.7-16
• /
• 1999

Stoichiometric and nonstoichiometric $Y_{3-x}Fe_{5+x}O_{12})$ polycrystalline samples (x=0.00, 0.05, 0.10, 0.30, -0.05, -0.10, -0.30) were prepared by solid state reaction method. The magnetic properties of the sample were investigated by FMR (ferromagnetic resonance) technique at microwave frequency 5.11 GHz (G-band) and 23.39 GHz (K-band) respectively. The spectroscopic splitting factor g were estimated to be 2.04~2.35 from the derivative absorption lines. As the samples became yttrium $(Y^{3+})$ excess and iron $(Fe^{3+})$ excess, Magnetizations were decreased. But resonance linewidth were increased. To investigate the anisotropy, the angular dependence of resonance magnetic fields were measured. Angular dependence of effective magnetizations were measured by FMR from 77 K to 300 K at K-band microwave frequency (23.39 GHz) and the saturation magnetizations were measured by VSM. The Bloch coefficients B and C were determined by fitting. $M_{eff}(0)$ was obtained by the extrapolation from 80 K. From this result, the spin wave stiffness constant D $(about\; 162~206 \;eV{\AA}^2)$and average square range of exchange interaction $$$(about \;5.84~12.13\;{\AA}^2)$ were determined.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.176-177
• /
• 2013

Surface plasmon polaritons (SPPs) have attracted the attention of scientists and engineers involved in a wide area of research, microscopy, diagnostics and sensing. SPPs are waves that propagate along the surface of a conductor, usually metals. These are essentially light waves that are trapped on the surface because of their interaction with the free electrons of conductor. In this interaction, the free electrons respond collectively by oscillating in resonance with the light wave. The resonant interaction between the surface charge oscillation and the electromagnetic field of the light constitutes the SPPs and gives rise to its unique properties. In this papers, we studied theoretical and experimental extraordinary transmittance (T) and reflectance (R) of 2 dimensional metal hole array (2D-MHA) on GaAs in consideration of the diffraction orders. The 2d-MHAs was fabricated using ultra-violet photolithography, electron-beam evaporation and standard lift-off process with pitches ranging from 1.8 to $3.2{\mu}m$ and diameter of half of pitch, and was deposited 5-nm thick layer of titanium (Ti) as an adhesion layer and 50-nm thick layer of gold (Au) on the semiinsulating GaAs substrate. We employed both the commercial software (CST Microwave Studio: Computer Simulation Technology GmbH, Darmstadt, Germany) based on a finite integration technique (FIT) and a rigorous coupled wave analysis (RCWA) to calculate transmittance and reflectance. The transmittance was measured at a normal incident, and the reflectance was measured at variable incident angle of range between $30^{\circ}{\sim}80^{\circ}$ with a Nicolet Fourier transmission infrared (FTIR) spectrometer with a KBr beam splitter and a MCT detector. For MHAs of pitch (P), the peaks ${\lambda}$ max in the normal incidence transmittance spectra can be indentified approximately from SP dispersion relation, that is frequency-dependent SP wave vector (ksp). Shown in Fig. 1 is the transmission of P=2.2 um sample at normal incidence. We attribute the observation to be a result of FTIR system may be able to collect the transmitted light with higher diffraction order than 0th order. This is confirmed by calculations: for the MHAs, diffraction efficiency in (0, 0) diffracted orders is lower than in the (${\pm}x$, ${\pm}y$) diffracted orders. To further investigate the result, we calculated the angular dependent transmission of P=2.2 um sample (Fig. 2). The incident angle varies from 30o to 70o with a 10o increment. We also found the splitting character on reflectance measurement. The splitting effect is considered a results of SPPs assisted diffraction process by oblique incidence.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2010.05a
• /
• pp.3.1-3.1
• /
• 2010

Water splitting reaction using photocatalysts is of great interest in the utilization of solar energy [1]. In the present work, visible light-responsive $TiO_2$ thin films (Vis-$TiO_2$) were prepared by a radio frequency magnetron sputtering (RF-MS) deposition method and applied for the separate evolution of $H_2$ and $O_2$ from water as well as the photofuel cell. Special attentions will be focused on the effect of HF treatment of Vis-$TiO_2$ thin films on their photocatalytic activities. Vis-$TiO_2$ thin films were prepared by an RF-MS method using a calcined $TiO_2$ plate and Ar as the sputtering gas. The Vis-$TiO_2$ thin films were then deposited on the Ti foil substrate with the substrate temperature at 873 K (Vis-$TiO_2$/Ti). Vis-$TiO_2$/Ti thin films were immersed in a 0.045 vol% HF solution at room temperature. The effect of HF treatments on the activity of Vis-$TiO_2$/Ti thin films for the photocatalytic water splitting reaction have been investigated. Vis-$TiO_2$/Ti thin films treated with HF solution (HF-Vis-$TiO_2$/Ti) exhibited remarkable enhancement in the photocatalytic activity for $H_2$ evolution from a methanol aqueous solution as well as in the photoelectrochemical performance under visible light irradiation as compared with the untreated Vis-$TiO_2$/Ti thin films. Moreover, Pt-loaded HF-Vis-$TiO_2$/Ti thin films act as efficient and stable photocatalysts for the separate evolution of $H_2$ and $O_2$ from water under visible light irradiation in the presence of chemical bias. Thus, HF treatment was found to be an effective way to improve the photocatalytic activity of Vis-$TiO_2$/Ti thin films. Furthermore, unique separate type photofuel cell was fabricated using a Vis-$TiO_2$ thin film as an electrode, which can generate electrical power under solar light irradiation by using various kinds of biomass derivatives as fuel. It was found that the introduction of an iodine ($I^-/{I_3}^-$) redox solution at the cathode side enables the development of a highly efficient photofuel cell which can utilize a cost-efficient carbon electrode as an alternative to the Pt cathode.