• Proceedings of the IEEK Conference
• /
• 2003.11a
• /
• pp.293-296
• /
• 2003

The enhancement of fingerprint image is necessary to improve the performance of fingerprint recognition. The enhancement of fingerprint image with Gabor Filter(GF) is widely used. However GF has the weakness such as long processing time and the sensitivity to ridge frequency. To overcome these weaknesses, we propose a Modified Anisotropic Gaussian Filter(MAGF) which is modified from Anisotropic Filter proposed by S. Greenburg's(SAF). This proposed MAGF can reduce the calculation time of ridge frequency and improve the weakness of sensitivity to ridge frequency. We also explained that MAGF is better than others mathematically and experimentally.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.30A no.6
• /
• pp.22-30
• /
• 1993

An integrated silicon pressure sensor with frequency output has been fabricated, measured, and tested. The standard bipolar process is applied and thin diaphragm was formed using EDP anisotropic etchant. Output frequency was 769 Hz-3.1 kHz at the pressure range of 0-10 psi. It operates at the temperature range of 0-50$^{\circ}C$. The frequency sensitivity was 233 Hz/psi and temperature sensitivity was 0.3 Hz/$^{\circ}C$. The power dissipation was 50mW.

• Journal of Institute of Control, Robotics and Systems
• /
• v.16 no.7
• /
• pp.720-725
• /
• 2010

In AGPS method, user position can be obtained even in the shadow region by improving signal sensitivity. A hybrid long integration scheme employing both coherent and non-coherent integration method is commonly used in AGPS receivers. Because coherent loss increases as residual frequency become large, residual frequency should be minimized to maximize coherent integration gain. This paper presents performance analysis of residual frequency estimator using FFT in fine-time assistance AGPS method. Considering the hardware complexity and the estimation accuracy, optimal length of FFT is proposed for GPS L1 C/A signal. Signal sensitivity for estimating the residual frequency is also analysed. By field experimental results, it is found that the residual frequency can be successfully estimated using 1 second snap-shot data when GPS signal strength is larger than -150 dBm and its RMS error is 3Hz.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.14 no.12
• /
• pp.1207-1222
• /
• 2004

In this paper, the explicit equations on the power consumption and sensitivity ratio of VCM-type actuator for disk drive are proposed. The power consumption and sensitivity ratio is derived in frequency domain. The power consumption during the track following of the actuator can be described well in frequency domain and it can be used to calculate the total power dissipation of the actuator which is needed to compensate the tracking and focusing errors. Also, the sensitivity ratio of an actuator is derived by using the reference servo of a disk drive and will be used to optimally obtain the performances of the actuator. This sensitivity ratio can persuasively explain the basis of the target performances of the actuator in the considerations of the reference servo. The usefulness of the proposed equations for the sensitivity ratio and power consumption of an actuator is shown by a lot of simulations. In the near future, we will verify the simulation results by experiments.

• Journal of Fashion Business
• /
• v.22 no.2
• /
• pp.14-26
• /
• 2018

This study was to explore purchasing behavior and repurchase intention by considering social-face sensitivity and conspicuous consumption. To do this, first, this study tried to explain how consumers had different characteristics for social-face sensitivity, conspicuous consumption, purchasing behavior, and repurchase intention for outdoor wear. Second, this study tested the relationship between consumer behavior (purchasing behavior and repurchase intention) and social-face sensitivity by considering the mediating effect of conspicuous consumption. As the results, first, there was a significant relationship between social-face sensitivity (sensitivity to saving face) and conspicuous consumption, which had a significant effect on the purchasing behavior with outdoor wear(purchase frequency, purchase cost). Second, social-face sensitivity (consciousness of shame) had a significant effect on conspicuous consumption (preference for famous brands, status symbol, pursuing fashion), and social face sensitivity (consciousness of social formality) had a significant effect on conspicuous consumption (preference for famous brands). The relationship between the conspicuous consumption and purchasing behavior showed that conspicuous consumption had significant effects on consumer behavior (purchase frequency, purchase cost). The relationship between the social-face sensitivity and purchasing behavior showed that being conscious of others had a significant effect on purchasing behavior. Third, purchasing behavior with outdoor wear had a significant effect on repurchase intention. Finally, this study confirmed that conspicuous consumption had a partially significant mediating effect on the relationship between social-face sensitivity (sensitivity to saving face) and purchasing behavior.

• Journal of Korean Ophthalmic Optics Society
• /
• v.20 no.3
• /
• pp.355-362
• /
• 2015

Purpose: To investigate the effects of the transmittance of diffusive blurson visual acuity and contrast sensitivity. Methods: Visual acuity and contrast sensitivity were measured by using Optec$^{(R)}$ 6500 in Healthy 30 subjects aged $22.83{\pm}0.50$ (male 13, female 17) who were recruited from university students. Cataract simulator was used as a tool for diffusive blur. Visual acuity and contrast sensitivity were measured with varying the transmittance of diffusive blur in order to simulate progression of cataract and concentration in fog. Results: Visual acuity was reduced proportionally with decreasing the transmittance of the diffusive blur as follows: $VA(T)=1.84{\times}10^{-2}T-0.645$. Contrast sensitivity was decreased in all spatial frequencies. Contrast sensitivity in a high spatial frequency band was a greater effect and was off the normal range of contrast sensitivity. The peak of contrast sensitivity was moved in the direction to low frequency. From an intersection point of contrast sensitivity function, we could calculated the transmittance of the diffusive blur being off the normal range and the shift to peak spatial frequency. The peak of contrast sensitivity function was observed to move from 6 to 3 cpd at transmittance of about 78.70%, the contrast sensitivities for all frequencies at transmittance of about 69.71% were deviated from the normal range. Conclusions: The transmittance of diffusive blur causes a reduction in visual acuity and contrast sensitivity, a deviation of normal range of contrast sensitivity, and a shift of peak contrast sensitivity. Therefore the more attention is required when suffering from cataracts or driving in fog.

• Journal of Broadcast Engineering
• /
• v.20 no.2
• /
• pp.238-247
• /
• 2015

We develop the signal processing method for adaptive implementing direction of signal and the frequency sensitivity of human visual system(HVS). Existing multibnad energy scaling method makes ringing artifact because it does not consider signal direction. To solve this problem, we use block gradient for signal direction in addition to existing method. And we use the fact that frequency component of signal is more sensitive than value of signal over human eyes. we enhance the signal according to contrast sensitivity function(CSF) which is the model of frequency sensitivity of human eye. Compared that the existing analysis models only improve the efficiencies in the existing systems, the developed method can process the image signals to be more desirable and suitable to HVS.

• Structural Engineering and Mechanics
• /
• v.68 no.1
• /
• pp.39-51
• /
• 2018

In this study, a frequency domain model updating method is presented using power spectral density (PSD) data. It uses the sensitivity of PSD function with respect to the unknown structural parameters through a decomposed form of transfer function. The stiffness parameters are captured with high accuracy through solving the sensitivity equations utilizing the least square approach. Using numerically noise polluted data, the model updating results of a truss model prove robustness of the method against measurement and mass modelling errors. Results prove the capabilities of the method for parameter estimation using highly noise polluted data of low ranges of excitation frequency.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.47 no.2
• /
• pp.1-7
• /
• 2010

This paper presents empirical equations indicating the high frequency performance characteristics of air-cored induction coil sensors with their constructional parameters. An air-cored induction coil sensor is widely used due to good linearity at low frequency ranges but the sensor has weakness of relatively low sensitivity to the magnetic field. At high frequency ranges, the sensitivity can be dramatically increased, largely depending on the frequency of the injected field, and this property can be a great asset to some electromagnetic inspections, since they utilize the interrogating current with a fixed frequency. The application of this property of the coil sensor requires the estimation of its high frequency performance. We made experiments on the frequency responses of the coil sensors under diverse constructional conditions and, on the basis of the experimental results, the high frequency performance, such as the resonant frequency and the sensitivity at the frequency, was estimated, as a function of the constructional parameters of the coil sensor. The good agreements between experimental and estimated data were reported.

• Journal of KSNVE
• /
• v.10 no.4
• /
• pp.648-654
• /
• 2000

A procedure to determine the realizable optimal positions of rigid supports is suggested to get a maximum fundamental natural frequency. a measured frequency response function based substructure-coupling technique is used to model the supported structure. The optimization procedure carries out the eigenvalue sensitivity analysis with respect to the stiffness of supports. As a result of such stiffness optimization, the optimal rigid-support positions are shown to be determined by choosing the position of the largest stiffness. The optimally determined support conditions are verified to satisfy the eigenvalue limit theorem. To demonstrate the effectiveness of the proposed method, the optimal support positions of a plate model are investigated. Experimental results indicate that the proposed method can effectively find out the optimal support conditions of the structure just based on the measured frequency response functions without any use of numerical model of the structure.