• Explosives and Blasting
• /
• v.8 no.4
• /
• pp.23-29
• /
• 1990

Some surface blasting vibration was measured to determine site constants and vibration frequency was analyzed. The results are summarized as follows; 1) Design method to predict particle velocities was introduced using the logarithmic normal distribution characteristics of peak particle velocities. 2) Scaled distance diagram to determine limiting charge was presented. 3) Line fitness between particle velocity and scaled distance didn't depend on dominant component of vibration. Prevail fitness was in the order of transverese, peak, vertical and radial component. 4) Dominant component of particle velocity didn't related to drilling direction. Frequency was lowered as distance enlarged. Duration time of vibration was shortened as charge decreased.

• Proceedings of the Korean Society for Emotion and Sensibility Conference
• /
• 2001.11a
• /
• pp.91-95
• /
• 2001

In this study, we estimated the behavior of the diversity of physiological responses under varied physical environmental factors by measuring variations of heart rate variability (HRV), an index of activity of cardiac autonomic control. Seven healthy young male adults consented and participated in the study. The environmental conditions consisted of thermal, lighting, and acoustic conditions. Two components of HRV were measured. one was the low frequency (LF) component of HRV, which provided a quantitative index of the sympathetic and parasympathetic (vagal) activities controlling the heart rate (HR). The other component measured was the high frequency (HF) component, which provided an index of the vagal tone. The percent contribution of physical environmental factors to the variations in HRV indices were calculated by ANOVA. The contribution of physical environmental factors to the variations in HR was higher than the contribution of HF and LF. However, the contribution of these factors was lower than the contribution related with individual difference in all indices. This result showed that the individual diversity of physiological responses is not a negligible quantity.

• KIEE International Transactions on Power Engineering
• /
• v.2A no.4
• /
• pp.153-159
• /
• 2002

Power transformer protective relay should block the tripping during magnetizing inrush and rapidly operate the tripping during internal faults. Recently, the frequency environment of power system has been made more complicated and the quantity of 2nd frequency component in inrush state has been decreased because of the improvement of core steel. And then, traditional approaches will likely be maloperate in the case of magnetizing inrush with low second harmonic component and internal faults with high second harmonic component. This paper proposes a new relaying algorithm to enhance the fault detection sensitivities of conventional techniques by using a fuzzy logic approach. The proposed fuzzy based relaying algorithm consists of flux-differential current derivative curve, harmonic restraint, and percentage differential characteristic curve. The proposed relaying was tested with relaying signals obtained from EMTP simulation package and showed a fast and accurate trip operation.

• Journal of the Korean Society for Precision Engineering
• /
• v.7 no.2
• /
• pp.47-57
• /
• 1990

In-process recognition of the cutting states is one of the very important technologies to increase the reliability of mordern machining process. In this study, practical methods which use the dynamic component of the cutting force are proposed to recognize cutting states (i.e. chip formation, tool wear, surface roughness) in turning process. The signal processing method developed in this study is efficient to measure the maximum amplitude of the dynamic component of cutting force which is closely related to the chip breaking (cut-off frequency : 80-500 Hz) and the approximately natural frequency of cutting tool (5, 000-8, 000 Hz). It can be clarified that the monitoring of the maximum apmlitude in the dynamic component of the cutting force enables the state of chip formation which chips can be easily hancled and the inferiority state of the machined surface to be recognized. The microcomputer in-process tool wear monitor- ing system introduced in this paper can detect the determination of the time to change cutting tool.

• Journal of the Korean Geophysical Society
• /
• v.6 no.1
• /
• pp.25-29
• /
• 2003

We suggest a method that vectorially composes 3-component earthquake records in the frequency domain, to reduce the uncertainties in the analysis of the Fourier amplitude spectrum. The use of the Fourier amplitude spectrum composed from 3 components has two advantages. First, it provides a more accurate estimate of seismic moment by eliminating the vector-partition term that appears in individual component. Second, it provides more accurate estimates of seismic moment, corner frequency, high-frequency decay constant($χ$) .etc., by enhancing the shape of the Fourier amplitude spectrum. The latter is especially useful in the analysis of small earthquakes with low signal-to-noise ratios.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.10
• /
• pp.601-607
• /
• 2016

Piezoelectric thick films of soft $Pb(Zr,Ti)O_3$ (PZT) based commercial material (S55) were fabricated using a conventional tape casting method. Ag-Pd electrodes were printed on the piezoelectric film at room temperature and all 5 layered films with a dimension of $12mm{\times}16mm$ were successfully laminated for a multi-layered piezoelectric ceramic actuator. The laminated specimens were co-fired at $1,100^{\circ}C$ for 1 h. A flat layered and dense microstructure was obtained for the $112{\mu}m$ thick piezoelectric actuator after sintering process. Thereafter, a prototype piezoelectric speaker was fabricated using the multi-layered piezoelectric ceramic actuator which can operate as a bimorph. Its SPL (sound pressure level) characteristic was also evaluated for speaker application. Frequency response revealed that the output SPL with a root mean square voltage of 10 V increased gradually to the highest peak of 87.5 dB for 1.5 kHz and exhibited a relatively stable behavior over the measured frequency range (${\leq}20kHz$) at a distance of 10 cm, implying that the fabricated piezoelectric speaker is potential for speaker applications.

• Proceedings of the IEEK Conference
• /
• 1999.11a
• /
• pp.1127-1130
• /
• 1999

In this paper, using one method of Additive Synthesis, Analysis-by-synthesis/Overlap-Add (ABS/OLA) method, analysis and synthesis of musical tones is processed. But peak detection of frequency domain is processed by proposed method considering the view of acoustics. It is that that harmonics frequency is times of main frequency. Using this fact, peak detection of frequency domain is useful for detection of tonal component identified musical note. It is possible to realize high-quality lour bit rate audio.

• 한국지구물리탐사학회:학술대회논문집
• /
• 2007.06a
• /
• pp.273-278
• /
• 2007

2-D MT surveys at the Century mine in Australia have been performed with very far remote reference in Esashi, Japan as well as Gregory Downs, which are roughly 6400 km and 80 km apart from the field site, respectively. Long period pulsations observed in this survey generally showed dominant $H_x$ polarization than $H_y$; $H_x$ component is more than 3 times stronger than $H_y$ component. Polarity reversal in magnetic field pointing east ($H_y$ component) has also been observed in long period pulsations, while $H_x$ component remain coherent between the hemispheres. Though $H_x$ component shows relatively good coherency than $H_y$ component between the hemispheres at frequencies lower than 0.01 Hz, it seems rather too far to be used as a remote reference for ordinary MT frequency band.

• Proceedings of the Korean Reliability Society Conference
• /
• 2004.07a
• /
• pp.183-190
• /
• 2004

Found important components in terms of frequency in the assembly (but not in terms of money). Component 39*** was most important. The failure mode was N69(no light on warning signal the cause of the failure was C15(bad connection). Formed a population for each component. Performed reliability and warranty cost analyses At the component level. At the subsystem level. At the system level. **They don'l trust the warranty cost analysis.** Reliability improvement. Among all the subsystems front \ulcorner subsystem is most vulnerable (among other things due to the large number of components in it), especially components 39*** and 28***.

• Proceedings of the KIEE Conference
• /
• 2003.07c
• /
• pp.1601-1603
• /
• 2003

Investigated about topology of each component of transformer and material choice method and property in this paper. Component of transformer is bobin winding, insulating paper, Varnish etc. And experiment and investigated special quality by primary winding of transformer and composition of secondary winding. Investigated loss of transformer and EMI decrease method. Investigated method to select winding size that consider frequency.