• Journal of the Korean GEO-environmental Society
• /
• v.20 no.1
• /
• pp.67-74
• /
• 2019

Frost heave is one of the representative engineering characteristics in cold regions. In South Korea, which is located in seasonal frost area, structural damage caused by frost heave and thaw happens and the need for research on the frost heave is increasing. In this paper, newly developed transparent temperature-controllable cell is used to focus on the frost heave. Frost susceptible artificial soil is used to analyze water intake rate which is one of the important factors in frost susceptibility criteria. Frost heave rate and water intake rate have similar behavior after heave by freezing of pore water converges. O-ring installed in the upper pedestal to measure water intake rate generates side friction between the inner wall of the freezing cell and O-ring, thereby hindering frost heave. Therefore, the frost susceptibility criteria using the water intake rate is not reliable. It is appropriate to use frost heave rate which has similar behavior with water intake rate. Frost heave tests were performed under two different specimen heights. Overburden pressure, temperature gradient and dry unit weight were set under similar state. Based on laboratory testing results, frost heave is independent on the specimen height.

• Journal of Korea Foundry Society
• /
• v.27 no.6
• /
• pp.243-249
• /
• 2007

The effect of Re addition and solidification rate on the directional solidification behavior of Ni-Al model alloy has been investigated. Directional solidification (DS) were carried out using the modified Bridgman furnace with various solidification rates. The solid/liquid interface during directional solidification was preserved by quenching the specimen after the desired volume fraction of original liquid was solidified. The equilibrium partition coefficients of Al and Re Were estimated by measuring the compositions at the quenched solid/liquid interface. Then, the effect of Re addition on the elemental segregation behavior was carefully analyzed. The differential scanning calorimetry results showed that the Re addition results in increased ${\gamma}'$ solvus and freezing range of the alloy. It was also shown that the primary dendrite arm spacing gradually decreases with increasing the Re content, while the secondary dendrite arm spacing appears to be independent on the Re content. The compositional analyses clearly revealed that the segregation of Al increased with increasing the Re content and solidification rate, while that of Re was found to be independent on the solidification rate in the range of $10{\sim}100{\mu}m/s$ due to its sluggish diffusion rate in the Ni solid solution.

• YAKHAK HOEJI
• /
• v.49 no.4
• /
• pp.291-298
• /
• 2005

Gardenia Jasminoides(GJ) is traditionally used for treatment of hepatic disease, insomnia, anxiety, and inflammatory disease. The aim of this study is to examine effects of GJ extract in response to stress. Animals of the normal group were not exposed to any stress and the control group were exposed to stress. The rats of the Ginseng and GJ supplementary group were orally administered once a day with 100mg of red ginseng extract, 100mg of GJ extract/kg body weight. The mice were given water containing 200mg of red ginseng extract, 200mg of GJ extract/100ml potable water. Animals were given supplements for 7 days without stress, and then were given supplements for 5 days with restraint and electroshock stress. After loading final stress, we examined stress related behavioral changes of experimental animals and measured the levels of blood corticosterone. GJ-supplementation partially blocked the stress effect on locomotion and elevated plus maze test in rats, and also partially blocked stress-induced behavioral changes such as freezing, burrowing, face-washing, smelling and rearing behavior in rats. The effect was almost equipotent to Ginseng's effect. GJ-supplementation didn't influence on fatigue related behavior or physical stress resistance. GJ-supplementation decreased the levels of blood corticosterone which is increased by stress in rats. These results suggest that GJ protects partially the living organism from stress attack and it has the potential to be used as a functional material to alleviate stress response.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.15 no.2
• /
• pp.107-115
• /
• 2011

This research studies the behavior of the FRP-concrete interface subjected to two environmental substances. Frist is to investigate the behavior by the application of different bonding materials at the interface between FRP and concrete, second is to understand a long-term performance at the interface by Freeze-thaw actions. The parameters considered in this research are the maximum bonding strength and the effective bonding length at the FRP-concrete interface. In the first experimental phase, three types of specimens are fabricated and tested considering the number of applied bonding materials and the Freeze-thaw tests are performed to evaluate the behavior of the interface in the cycle range of 0 to 300 cycles. Finally, it is known that there is a 5~7% difference of the effective bonding length between applied bonding materials and the values for the maximum stress and the effective length under Freeze-thaw action are varied randomly as the freeze-thaw cycle is increased even though initial reduction of their capacities are occurred.

• Journal of Industrial Technology
• /
• v.21 no.B
• /
• pp.187-193
• /
• 2001

This paper is results of extensive centrifuge model experiments about design factors influencing the bearing capacity and the settlement behaviors of SCP (Sand Compaction Pile). Centrifuge model tests were carried out changing design factors for SCP method such as replacement area ratio (as= 20, 40, 70%), improvement ratio to footing width (W/B = 1, 2, 3), and amount of fines in sand pile (#200 = 5, 10, 15). Therefore, the effects of these design factors on the bearing capacity and the settlement behavior of SCP were investigated and changes of stress concentratio rato due to such an design factors were also investigated. Centrifuge model testing technique for preparing and installing centrifuge model of sand compaction pile, using freezing them, was also developed. As results of centrifuge model tests, more fines in sand compaction pile increases the bearing capacity of SCP. Optimum improvement ratio to footing width was found to be 2. Values of stress concentration ratio was in the ranges of 1.5 - 3.5. The depth of bulging in sand piles was found in the range of 2.0 - 2.5 times of pile diameter.

• Journal of Industrial Technology
• /
• v.22 no.A
• /
• pp.145-151
• /
• 2002

This paper is results of extensive centrifuge model experiments about design factors influencing the bearing capacity and the settlement behaviors of SCP (Sand Compaction Pile). Centrifuge model tests were carried out changing design factors for SCP method such as replacement area ratio (as= 20, 40, 70%), Improvement ratio to footing width (W/B = 1, 2, 3), and amount of fines m sand pile (#200 = 5, 10, 15). Therefore, the effects of these design factors on the bearing capacity and the settlement behavior of SCP were investigated and changes of stress concentratio rato due to such an design factors were also investigated. Centrifuge model testing technique for preparing and installing centrifuge model of sand compaction pile, using freezing them, was also developed. As results of centrifuge model tests, more fines in sand compaction pile increases the bearing capacity of SCP. Optimum improvement ratio to footing width was found to be 2. Values of stress concentration ratio was in the ranges of 1.5 - 3.5. The depth of bulging in sand plies was found in the range of 2.0 - 2.5 times of pile diameter.

• Journal of Powder Materials
• /
• v.21 no.5
• /
• pp.366-370
• /
• 2014

The present study demonstrates the effect of solidification condition on the pore structure in freeze drying process using the slurries of CuO/sublimable vehicles. Camphene and Camphor-45 wt% naphthalene based slurries with 14 vol% CuO powder were frozen into a mold at $-25^{\circ}C$, followed by sublimation at room temperature. The green bodies were hydrogen-reduced and sintered at $500^{\circ}C$ for 1 h. The porous Cu specimen, frozen the CuO/camphene slurry into the heated mold of the upper part, showed large pores with unidirectional pore channels and small pores in their internal wall. Also, it was observed that the size of large pores was decreasing near the bottom part of specimen. The change of pore structure depending on the freezing condition was explained by the nucleation behavior of camphene crystals and rearrangement of solid powders during solidification. In case of porous Cu prepared from CuO/Camphor-naphthalene system, the pore structure exhibited plate shape as a replica of the original structure of crystallized vehicles with hypereutectic composition.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2009.05a
• /
• pp.21-22
• /
• 2009

This paper presents the results of an experimental study on flexural behavior and cracking process of concrete beams subjected to cycles of freezing and thawing after patch-repaired with strain-hardening cement composites (SHCCs). The SHCCs were reinforced with hybrid 0.75% PVA and 0.75% PE fibers. Experimental testing of concrete beams patch-repaired with SHCCs revealed that the SHCC patch-repair system without freeze thaw (FT) exposure showed average 3.31 times increased load carrying capacity and for beams exposed to 300 FT cycles, load carrying capacity increased up to 2.42 times. Cracking damage of SHCC patch-repaired beams mitigated compared to plain concrete beams but this trend decreased under FT exposure.

• Proceedings of the Membrane Society of Korea Conference
• /
• 1998.10a
• /
• pp.153-155
• /
• 1998

PTFE 합성공정에서 대량으로 사용하는 고가의 음이온계 유화제를 분리/회수하는 것은 경제적인 문제 뿐만 아니라 환경적으로도 매우 중요하다. 음이온계 유화제의 회수에는 Water-evaporation, ion-exchange, freezing, electrodialysis등의 방법을 사용할 수 있다. 그러나 회수에 드는 경비가 높고 장치가 복잡하다는 단점이 잇다. 반\ulcorner에 막분리 공정은 장치가 간단하고 상대적으로 경비가 적게 든다는 장점이 있다. 본 연구에서는 음이온계 유화제를 분리/회수하기 위해서 역삼투 공정을 사용하였다. 그러나 역삼투 공정과 같이 압력을 분리의 구동력으로 하는 막분리 공정에서는 농도분극 및 막오염 현상에 의한 투과량의 감소가 심각하게 일어나며 전체적으로 막분리 공정의 경제성을 떨어뜨리는 주된 요인이 된다. 특히 이온성 막을 사용할 경우 막과 이온성 용질간의 정전기적 포텐셜이 화학적 포텐셜과 함께 투과분리의 구동력을 이루게 되므로 투과거동이 매우 달라지게 된다. 본 연구에서는 막 재료의 이온특성과 음이온성 용질의 농도에 따른 막오염 현상의 관찰 및 이것이 투과거동에 미치는 영향을 관찰하였다. 이를 위해 Sodium alginate, Chitosan, Poly(vinyl alcohol)을 이용하여 각각 음이온성, 양이온성, 중성 막을 제조하여 투과거동을 관찰하였다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.3 no.4
• /
• pp.1-11
• /
• 1999

Thermal behavior of spacecraft propulsion system utilizing monopropellant hydrazine ($N_2$$H_4$) is addressed in this paper. Thermal control performance to prevent propellant freezing in spacecraft-operational orbit was test-verified under simulated on-orbit environment. The on-orbit environment was thermally achieved in space-simulation chamber and by the absorbed-heat flux method that implements an artificial heating through to the spacecraft bus panels enclosing the propulsion system. Test results obtained in terms of temperature history of propulsion components are presented and reduced into duty cycles of the avionics heaters which are dedicated to thermal control of those components. The duty cycles are subsequently converted into the electrical power required in the operational orbit. Additionally, cyclic temperature of each component, which was made under thermal-balanced condition of spacecraft, is compared to the acceptable design range and justified from the viewpoint of system verification.