• 한국강구조학회 논문집
• /
• 제22권4호
• /
• pp.293-303
• /
• 2010

본 연구는 강구조 설계기준(KBC 2009)에서 골조 안정성 평가를 위해 제시한 하중증폭계수를 적용한 직접해석법의 적용 방법에 따른 영향을 해석적 방법을 통해 평가하는데 목적이 있다. 이를 위해 KBC 2009에서 제안하고 있는 가상수평하중 적용 방법, 휨강성 감소 방법, B2 계수 산정 방법 등을 각각 적용한 직접해석을 3층 1스팬 및 5층 3스팬 비가새 강구조 골조에 대해 실시하고, 그 해석 결과를 2차 비탄성 해석 결과와 비교하여 각 적용 방법의 영향을 평가하였다. 직접해석법 적용 방법 이외에 외적 요인의 영향을 고찰하기 위해 골조의 규모, 기둥의 축력비, 축력의 층별분포 등도 변수로 추가하였다. 연구 결과 소요압축강도는 직접해석법 적용 방법에 따른 차이가 크지 않은 것으로 나타났으며, 소요휨강도는 가상수평하중 누계 및 추가 적용, 층강성 개념 B2 계수를 직접해석법에 적용시 적절한 결과를 나타내었다.

• 한국기계가공학회지
• /
• 제20권1호
• /
• pp.116-124
• /
• 2021

In this study, the reliability of vehicle frames employed in small electric road sweepers was assessed through durability testing. The frames were tested under three conditions, whereby mechanical loads were applied to (1) the entire frame, (2) the front frame, and (3) the rear frame. The strain distributions in the loaded frames were determined through a combination of direct strain gauge measurements and supplementary numerical analysis. While subtle differences were observed between the experimental and numerical analyses, both methods successfully yielded comparable deformation patterns. Thus, the dependence of stress distribution and the state of the frame on loading conditions could be fully identified through our combined structural and numerical analysis.

• Structural Engineering and Mechanics
• /
• 제25권2호
• /
• pp.147-160
• /
• 2007

In this paper, a dynamic analysis based on the fuzzy set theory is presented as a possible complementary tool to the classical stochastic methods for dynamic analyses. Material parameters of a structure are influenced by uncertainties and therefore they are considered to be fuzzy quantities with given distributions, that means fuzzy numbers with given membership functions. The fuzzy dynamic analysis is conducted with help of fuzzy arithmetic defined on the so-called ${\alpha}$-cuts. The results of the analysis are also obtained in the form of fuzzy numbers, which compared to the stochastic methods is less computationaly expensive while at the same time they still provide information about the distribution of a quantity. This method is demonstrated on an analysis of a two-dimensional frame subjected to possible seismic load, where the uncertain eigenmodes and eigenfrequencies are used in the modal analysis.

• 한국산학기술학회논문지
• /
• 제15권7호
• /
• pp.4611-4617
• /
• 2014

본 논문은 강접골조의 예비구조설계에서 부재력을 근사적으로 예측하기 위한 연구이다. 기둥간의 축력 분포를 선형으로 가정하는 캔틸레버법에서 기둥의 변곡점 위치를 부재의 중간으로 가정하는데 이것은 몇 개의 사례를 통해 행렬해석법과 비교한 바 오차가 매우 심하다는 것을 알 수 있다. 다양한 골조를 해석한 결과를 분석해보면, 부재력은 기둥과 보의 경간비, 단면2차모멘트비에 따라 달라짐을 알 수 있다. 본 연구에서는 기존의 방법과는 다른 방법으로 기둥의 부재력을 예측하는 방법을 제시하였다. 예제를 통하여 기존의 방법보다 향상된 해를 얻을 수 있었다.

• 한국지진공학회논문집
• /
• 제12권2호
• /
• pp.53-67
• /
• 2008

본 연구에서는 전단벽-모멘트골조 시스템으로서 전단벽이 주로 횡력을 부담하는 철근콘크리트 건물을 대상으로 다양한 설치형식과 마찰력의 총량 및 분포를 갖는 마찰형 감쇠기의 제진보강 효과를 수치해석을 통해 비교 분석하였다. 감쇠기의 설치형식으로서 전단벽에 인접한 대각가새형, 벽체가 없는 골조를 보강하는 대각가새형 및 벽체 단부를 보강하는 수직경계요소형을 고려하였다. 하중기준 강화로 설계용보다 크게 증가한 지진하중에 대해 건물의 재료비선형성을 고려한 비선형시간이력해석을 수행하여 에너지소산, 횡하중 및 부재손상도 측면에서 마찰형 감쇠기의 제진성능을 비교 분석하였다. 기준마찰력의 30% 수준의 총마찰력을 갖는 벽체보강 대각가새형 설치형식이 전반적으로 가장 우수한 제진성능을 보이며,이 경우에 마찰력 배분방식은 중요하지 않았다. 또한 일부층에 집중설치함으로써 전층설치에 약간 못미치는 제진성능을 얻을 수 있었다.

• 콘크리트학회지
• /
• 제3권3호
• /
• pp.111-119
• /
• 1991

작금에 사용되고 있는 RC 구조물의 대개의 내진설계기법은 지진시 RC 구조물에 발생되는 손상의 분포상태를 고려치 않고 있다. 본 논문은 철근 콘크리트 구조물의 새로운 내진설계법 즉 Miner's 법칙을 수정한 지진 발생시의 흡수에너지(Dissipated Energy)를 변수로 하는 손상모델(3)를 사용하여 RC 프레임의 각각의 Node에서의 손상정도를 수치적으로 나타내고 이들 손상값의 크기가 전 부재에 고르게 분포토록 하기 위하여 각 부재의 주철근량을 설계변수로 채택한 설계기법을 소개하였다. 사용된 이력모델 및 손상모델의 정확성을 평가하기 위하여 해석적인 하중-변형곡선을 재생하여 실험곡선과 비교분석하였으며 제안된 내진설계법의 유용성은 3-bay 4-story 프레임 모델을 사용하여 입증하였다.

• Steel and Composite Structures
• /
• 제14권6호
• /
• pp.523-545
• /
• 2013

In this study, the effect of presence and distribution of masonry infill walls on the mid-rise steel frame structures having soft ground storey was evaluated by implementing finite element (FE) methods. Masonry infill walls were distributed randomly in the upper storey keeping the ground storey open without any infill walls, thus generating the worst case scenario for seismic events. It was observed from the analysis that there was an increase in the seismic design forces, moments and base shear in presence of randomly distributed masonry infill walls which underlines that these design values need to be amplified when designing a mid-rise soft ground storey steel frame with randomly distributed masonry infill. In addition, it was found that the overstrength related force modification factor increased and the ductility related force modification factor decreased with the increase in the amount of masonry infilled bays and panels. These must be accounted for in the design of mid-rise steel frames. Based on the FE analysis results on two mid-rise steel frames, design equations were proposed for determining the over strength and the ductility related force modification factors. However, it was recommended that these equations to be generalized for other steel frame structure systems based on an extensive analysis.

• Structural Engineering and Mechanics
• /
• 제85권1호
• /
• pp.55-64
• /
• 2023

Energy-based seismic design and evaluation methods are promising to be involved in the next generation design codes. Accordingly, determining the distribution of earthquake input energy demand among floor levels is quite imperative in order to develop an energy-based seismic design procedure. In this paper, peak floor input energy demands are achieved from relative input energy response histories of several reinforced concrete (RC) frames. A set of 22 horizontal acceleration histories selected from recorded near-fault earthquakes and scaled in time domain to be compatible with the elastic acceleration design spectra of Turkish Seismic Design Code are used in time history analyses. The distribution of the computed input energy per mass values and the arithmetic means through the height of the considered RC frames are presented as a result. It is found that spatial distribution of input energy per mass is highly affected by the number of stories. Very practical yet consistent formulation of distributing the total input energy to story levels is achieved, as a most important contribution of the study.

• 대한안전경영과학회지
• /
• 제10권1호
• /
• pp.205-213
• /
• 2008

Servicizing is defined 'not as to sell the products but as to sell the functions'. This study was done on the methods for revitalization as the object items of navigation & antenna among car parts. The direct door-to-door survey was done for 101 enterprises (direct-management stores) and percentage & t-test were done for statistics. The results can be summarized like followings. First, PR on servicizing is required. Second the optimized methods can be obtained by incorporating reuse & recycling distribution systems of servicizing with the existing recovery system Reuse distribution system can be constructed rationally because inventory control is being done correct1y with the periodic recovery. Finally, as for the analysis on the relative importance of main factors of servicizing, it shows that supports & providing the concrete frame of the government & local autonomous body are important.

• Journal of Contemporary Eastern Asia
• /
• 제16권2호
• /
• pp.59-81
• /
• 2017

The emergence of the new audiences floating across multimedia platforms and engaging in TV production and distribution have forced producers and broadcasters to think of not only the fragmented distribution of their content but also the development of a new format beyond the frame of traditional TV production. A Korean entertainment TV show My Little Television combining the form of live webcasting and traditional TV show reflects such a trend. Because of the distinct format, My Little Television carries out a unique strategy in managing the two screens - Internet and TV. The dualistic production requires all players to understand not only online subculture and communication styles and methods, but also implicit and explicit rules of traditional TV production. Through text and visual image analysis on the show, this study discusses how MLT negotiates with the original Internet text, the producers' paratext, and the supertext of the national TV network in the context of the transitory screen culture.