• 상하수도학회지
• /
• 제9권3호
• /
• pp.78-87
• /
• 1995

A study on the fouling control by periodical ozone-scrubbing was conducted in a membrane filtration process for drinking water treatment. Hydrophilic hollow fiber polyethylene membrane with pore size of $0.1{\mu}m$ and its surface area of $0.42m^2$ was used. Dead-End filtration method was selected to obtain high efficiency of energy. Laboratory prepared synthetic raw water with kaolin was used and the membranes were scrubbed by ozone once in an hour and once in two hours. When the duration of ozone scrubbing was increased from 10 seconds to 20 seconds, the rate of membrane fouling was significantly decreased. Although the frequency of ozone-scrubbing was reduced from once in an hour to once in two hours. the effect of fouling control was unchanged. However, ozone-scrubbing was not effective after a membrane was fouled and washed with detergent for reuse. Among several possible working effects of ozone, bactericidal effect was confirmed to be the primary reason of fouling control.

• Journal of Advanced Marine Engineering and Technology
• /
• 제23권2호
• /
• pp.131-139
• /
• 1999

An experimental study was conducted to investigate the fouling effects of geothermal water scale deposited onto a heating surface upon its forced convection heat transfer characteristics. Scales deposited onto the heating surfaces of heat exchangers seriously reduce the heat transfer perfor-mance and also increase the hydrodynamic drag. Accordingly fouling is an important problem in the design and operation of heat exchangers. The cylinders were settled in tandem with equal dis-tance between neighbouring cylinders and only the test cylinder was heated under the condition of constant heat flux. The Reynolds number was varied from 13000310 through 50003100. It is found that the heat transfer of the in-line tube banks greatly varies with the fouling of geothermal water scale especially its scale height. Further the local and average Nusselt numbers strongly depend upon the cylinder spacing and the Reynolds number.

• 멤브레인
• /
• 제28권1호
• /
• pp.1-20
• /
• 2018

고분자 재질의 압력 구동 기반 분리막을 이용하여 담수를 얻기 위한 공정은 에너지 효율이 높은 방법으로 알려져 있다. 하지만, 분리막 운전 중에 투과성능을 떨어트리는 막 오염 문제가 발생 하기에, 막 오염을 제어하는 것은 분리막 공정의 에너지 효율을 높이는 데 필수적이다. 막 오염은 일반적으로 분리막 표면과 막 오염 물질과의 상호 작용으로 발생하며, 분리막 표면을 개질하는 방법은 막 오염을 방지하여 높은 투과 특성을 지속적으로 유지하게 할 수 있는 좋은 방법 중 하나이다. 본 논문에서는 압력 구동 기반 분리막인 미세여과, 한외여과, 나노여과 및 역삼투용 분리막의 표면을 개질할 수 있는 방법을 정리하였다. 구체적인 개질 방법으로는 개질 물질의 흡착 및 코팅 방법인 물리적 방법과 가교제 이용, 자유 라디칼 중합(FRP), 원자 이동 라디칼 중합(ATRP), 플라즈마 및 자외선 조사 기반 중합인 화학적 방법으로 나누어 정리하였다. 본 총설에서는 최근 논문상에 보고되고 있는 물리화학적 표면 개질 방법을 소개하고, 막 오염 저항성을 높일 수 있는 분리막 제조를 위한 연구방향을 제시하고자 한다.

• 설비공학논문집
• /
• 제15권10호
• /
• pp.802-808
• /
• 2003

The air-side particulate fouling of the HVAC heat exchangers degrades the performance of cooling capacity, pressure drop across a heat exchanger, and indoor air quality. The purpose of this study is to investigate the fouling characteristics using accelerated particle loading system. The fouling characteristics are analyzed as functions of a dust concentration, a face velocity and a wet or dry surface condition. The pressure drop increases with increasing test operation and reaches constant asymptotic level. For the saturated condition due to particle loading, the pressure drop across the slitted finned-tube heat exchangers at the face velocity of 1 m/sec increases up to 57% and the cooling capacity decreases about 2%. The cooling capacities are not affected greatly by the presence of the fouling deposits if the thickness of the fouling deposits can not change substantially the flow pattern through the fins.

• Environmental Engineering Research
• /
• 제21권2호
• /
• pp.196-202
• /
• 2016

Membrane bioreactor (MBR) technology has previously been used by water industry to treat high salinity wastewater. In this study, an anoxic-oxic biofilm-membrane bioreactor (AOB-MBR) system has been developed to treat mustard tuber wastewater of 10% salinity (calculated as NaCl). To figure out the effects of operating conditions of the AOB-MBR on membrane fouling rate ($K_V$), response surface methodology was used to evaluate the interaction effect of the three key operational parameters, namely time interval for pump (t), aeration intensity ($U_{Gr}$) and transmembrane pressure (TMP). The optimal condition for lowest membrane fouling rate ($K_V$) was obtained: time interval was 4.0 min, aeration intensity was $14.6 m^3/(m^2{\cdot}h)$ and transmembrane pressure was 19.0 kPa. And under this condition, the treatment efficiency with different influent loads, i.e. 1.0, 1.9 and $3.3kgCODm^{-3}d^{-1}$ was researched. When the reactor influent load was less than $1.9kgCODm^{-3}d^{-1}$, the effluent could meet the third discharge standard of "Integrated Wastewater Discharge Standard". This study suggests that the model fitted by response surface methodology can predict accurately membrane fouling rate within the specified design space. And it is feasible to apply the AOB-MBR in the pickled mustard tuber factory, achieving satisfying effluent quality.

• 상하수도학회지
• /
• 제35권3호
• /
• pp.197-204
• /
• 2021

In MBR, extracellular polymeric substance (EPS) is known as an important factor of fouling; soluble EPS (sEPS) affects internal contamination of membrane, and bound EPS (bEPS) affects the formation of the cake layer. The production of EPS changes according to the composition of influent, which affects fouling characteristics. Therefore, in this study, the effects of the F/M ratio on the sEPS concentration, bEPS content, and fouling were evaluated. The effects of F/M ratio on the amount and composition of EPS were confirmed by setting conditions that were very low or higher than the general F/M ratio of MBR, and the fouling occurrence characteristics were evaluated by filtration resistance distribution. As a result, it was found that the sEPS increased significantly with the increase of the F/M ratio. When the substrate was depleted, bEPS content decreased because bEPS was hydrolyzed into BAP and seemed to be used as a substrate. In contrast, when the substrate is sufficient, UAP (utilization-associated products) was rapidly generated in proportion with the consumption of the substrate. UAP has a relatively higher Protein/Carbohydrate ratio (P/C ratio) than BAP, and this means, it has a higher adhesive force to the membrane surface. As a result, UAP seems like causing fouling rather than BAP (biomass-associated products). Therefore, R_f (Resistance of internal contamination) increased rapidly with the increase of UAP, and R_c (Resistance of cake layer) increased with the accumulation of bEPS in proportion, and as a result, the fouling interval was shortened. According to this study, a high F/M ratio leads to an increment in UAP generation and accumulation of bEPS, and by these UAP and bEPS, membrane fouling is promoted.

• 멤브레인
• /
• 제20권2호
• /
• pp.120-126
• /
• 2010

본 연구에서는 $TiO_2$ 나노입자로 표면침적된 polyethersulfone (PES) 정밀여과 분리막이 자연유기물로 인한 분리막 막힘현상(파울링)에 미치는 영향을 관찰하였다. $TiO_2$ 나노입자로 표면침적된 PES 정밀여과 분리막의 자연유기물 파울링 거동에 $TiO_2$ 나노입자의 결정구조와 용액의 pH 그리고 $Ca^{+2}$이 미치는 영향을 관찰하였다. 연구결과, $TiO_2$ 나노입자로 표면 개질된 정밀여과 분리막은 자연유기물에 의한 파울링 현상을 현저하게 감소시킬 수 있음을 확인 할 수 있었다. 그러나 이와같은 현상은 $TiO_2$ 나노입자의 결정구조와 용액의 성상에 매우 의존하는 것으로 나타났다. 자연유기물 파울링의 감소는 결정구조가 상대적으로 불안정한 anatase $TiO_2$ 나노입자를 분리막에 표면침적 시, 용액 중 $Ca^{+2}$이 존재하지 않을 때 상대적으로 높은 pH에서 효과적인 것으로 관찰되었다. 그러나 $Ca^{+2}$의 첨가 시 이와 같은 효과는 높은 pH에서 더욱 증가할 수 있음을 확인할 수 있었다. 반면, 결정구조가 상대적으로 안정한 rutile $TiO_2$ 나노입자의 경우 자연유기물의 파울링 감소는 용액의 조성에 큰 영향을 받지 않는 것으로 나타났다.

• 멤브레인
• /
• 제26권3호
• /
• pp.205-211
• /
• 2016

새롭게 제조된 납석기반 세라믹 멤브레인의 기본성능을 관찰하였다. 실규모 하수처리 membrane bioreactor (MBR) 미생물 고농도 현탁액을(MLSS : 약 6 g/L) 처리하는 납석기반 멤브레인 파울링 현상을 서로 다른 공기 폭기량과 막 간격에 대해 관찰하였다. 공극크기가 약 $1.0{\mu}m$인 비코팅 납석기반 세라믹 멤브레인 지지체의 순수투과도의 경우 약 $1100L/m^2{\cdot}hr{\cdot}bar$로 측정되었으나 알루미나로 코팅된 납석기반 세라믹 멤브레인은 공극크기의 감소로($0.3{\mu}m$) 순수 투과도는 두 배가량 감소하였다. 실규모 MBR 미생물 현탁액을 적용한 침지식 여과실험에서 납석 기반 세라믹 멤브레인 지지체의 경우 투과플럭스 20 LMH에서 공기폭기량을 증가시켰을 때 파울링은 감소하였다. 그러나 공기폭기가 파울링에 미치는 영향은 막간 간격에 상당히 의존하였다. 일정한 공기폭기 유량에서 막간간격의 증가는 파울링을 감소시켰으나 막간 간격을 3.5에서 5.4 cm로 증가시켰을 때 파울링 속도는 오히려 증가하였다. 알루미나 용액으로 표면코팅된 납석기반 지지체의 경우 유사한 결과가 관찰되었으나 파울링 속도는 코팅층이 없는 지지체에 비해 상대적으로 낮았다. 표면코팅에 상관없이 납석기반 지지체와 멤브레인의 경우 거의 완벽한 SS 제거효율을 나타내었다. 또한 납석 지지체 알루미나 표면코팅은 PEG (분자량 8,000 kDa)을 적용하였을 시 멤브레인의 유기물 배제율을 향상시켰다.

• 한국막학회:학술대회논문집
• /
• 한국막학회 2004년도 Proceedings of the second conference of aseanian membrane society
• /
• pp.25-28
• /
• 2004

In recent years, membranes have become fully or partially integrated into all facilities that produce drinking water since membrane processes can resolve technically complex and, at times, conflicting requirements related to compliance with multi-contaminant regulations. However, NF or RO technologies are hydraulically limited by the feed water quality that causes the fouling in a membrane system. In particular, NF or RO systems involved in surface water treatment generally require extensive pretreatment for controlling membrane fouling.(omitted)

• 상하수도학회지
• /
• 제30권3호
• /
• pp.327-334
• /
• 2016

The effects of dissolved inorganic and organic matter in seawater and the characteristics of fouling on the membrane surface were investigated within membrane distillation (MD) process. The changes of the membrane flux of PE and PVDF hollow fiber membranes under natural and synthetic seawater were compared with given variances of temperature. The flux of both membranes under the synthetic seawater, without any organic matter, were higher than that of the natural seawater, indicating the organic fouling on the membrane surface. The surface of the membrane was analyzed using scanning electron microscope (SEM) to examine the fouling. The experiment with organics has shown the formation of thin film over the membrane surface, while the experiment with inorganics has shown only the formation of inorganic crystals. The results indicated the organic matter as the major foulants and that the organics affected the formation of the crystals. Permeate water conductivity of all conditions verified the quality of the water to be better if not similar to that of RO.