• 열처리공학회지
• /
• 제14권2호
• /
• pp.81-88
• /
• 2001

The effects of post-oxidation and sulfnitriding treatments on the phase transformation in the nitrided case of tool steels have been studied. Dense and compact $Fe_3O_4$ layer was formed at the outer surface of nitride compound layer by post-oxidation treatment and multi layer of iron sulfide(FeS) was formed in the compound layer by sulfnitriding treatment. The surface hardness decreased because of formation of the soft oxide or sulfide at the nitride surface. Diffusion layer of nitride case was not affected by post-oxidation treatment or sulfnitriding treatment of nitrided alloy tool steels.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2010년도 제35회 추계학술대회논문집
• /
• pp.271-275
• /
• 2010

연소기 재생냉각 챔버 노즐확장부의 외피구조물 제작을 위한 성형치구 설계에 대한 연구를 수행하였다. 연소기 챔버에서 두께가 얇은 외피구조물은 판재의 성형을 이용하여 제작한다. 노즐확장부 외피구조물의 성형에서 노즐확장부와 동일한 형상의 치구로 성형하면 성형 후 구조물의 형상이 노즐확장부와 일치하지 않고 탄성복원에 의하여 그 형상이 변화한다. 따라서 노즐확장부 형상과 동일한 형상으로 성형을 완성하기 위해서는 탄성복원을 고려한 성형치구의 설계가 필요하다. 본 연구에서는 초기 성형 후 탄성복원에 의한 노즐형상과 실제 구조물의 형상과의 오차를 없애기 위하여 오차를 보상한 새로운 성형치구용 형상을 생성하였다. 구조해석 결과 설계 수정된 성형치구로 성형하면 노즐 형상과 성형된 구조물과의 형상 오차가 매우 작게 감소함을 확인할 수 있었다.

• 한국기계가공학회지
• /
• 제2권1호
• /
• pp.85-91
• /
• 2003

The experimental study for turning circular free fanned surface with TiN coated insert tool was conducted for different cutting conditions such as cutting speed, feed rate and depth-of-cut. For the fluctuation of 1.0mm depth-of-cut, the characteristics for machined surface and tool wear were less influenced by the feed rate and cutting speed than those of higher depth of cut. The higher surface roughness and surface precision were obtained in lower cutting speed. For the fluctuation of 1.5mm depth-of-cut, the higher surface roughness was obtained for the case of the lower feed rate of 0.05-10mm/rev and the higher cutting speed of 80m/min. For the fluctuation of 2.0mm depth-of-cut, the surface roughness and surface precision were too worse to machine the specimen And the flank wear on the tool was increased rapidly rather than the crater wear.

• 열처리공학회지
• /
• 제24권1호
• /
• pp.37-44
• /
• 2011

High temperature wear of AlCrN coated tool steels sliding against the ultra-high strength boron steels used for hot press forming has been studied. The sliding wear tests have been carried out using a pin-on-disc of configuration under applied normal load of 50 N for 20 min with heating the ultra-high strength boron steels up to $800^{\circ}C$. Characterizations of tribolayers formed on the contacting surfaces between the tribopairs of the AlCrN coated tool steels and the ultra-high strength boron steels have been studied. It was found on the tribolayers of the AlCrN coated tool steels that microcracking and oxides containing Fe and Cr to increase friction coefficient were formed at the early stage of sliding wear, followed by the generation of the smeared oxide layers containing Fe transferred from the tribopair to decrease friction coefficient. This may mainly contribute to very low specific wear rate of the AlCrN coated tool steels sliding against the ultra-high strength boron steels, resulting from oxideoxide contact between the tribopair.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 The 8th Asian Symposium on Precision Forging ASPF
• /
• pp.158-161
• /
• 2003

Extrusion of forward-gear and backward-rod by combined extrusion with controlling the extrusion velocity using a counter tool is studied. In the combined forward-backward extrusion with controlling extrusion velocity, only parts with short gear can be formed. To obtain longer gear parts, extrusion with reverse ram motion is carried out after the combined forward-backward extrusion process. In this method, combined forward-backward extrusion is carried out until excessive extrusion length is attained and then, the motion of the punch is stopped and the counter tool is moved in the inverse direction and returned to the position for obtaining the desired extrusion length. The experiment is carried out by using lead for billets as a model material. With reverse ram motion, longer gear teeth without under-filling defect can be formed than that by only combined extrusion with controlling extrusion velocity.

• International Journal of Precision Engineering and Manufacturing
• /
• 제5권3호
• /
• pp.35-42
• /
• 2004

This research describes that the cutting characteristics and tool wear behavior in the micro cutting of three kinds of wear resistant cemented carbides (WC-Co; V40, V50 and V60) using PCD (Poly Crystalline Diamond) and PCBN (Poly crystalline Cubic Boron Nitride) cutting tools by use of the SEM (Scanning Electron Microscope) direct observation method. The purpose of this research is to present reasonable cutting conditions from the viewpoint of high efficient cutting refer to a precise finished surface and tool wear. Summary of the results is as follows: (1) The cutting forces tend to increase as the increase of the weight percentage of WC particles, and the thrust forces was larger than the principal forces in the cutting of WC-Co. These phenomena were different from the ordinary cutting such as cutting of steel or cast iron. (2) The cutting speed hardly influenced the thrust force, because of the frictional force between the cutting tool edge and small WC particles at low cutting speed region such as 2$\mu\textrm{m}$/s. It seemed that the thrust cutting force occurred by the contact between the flank face and work material near the cutting edge. (3) The wear mechanism for PCD tools is abrasion by hard WC particles of the work materials, which leads diamond grain to be detached from the bond. (4) From the SEM direct observation in cutting the WC-Co, it seems that WC particles are broken and come into contact with the tool edge directly. This causes tool wear, resulting in severe tool damage. (5) In the orthogonal micro cutting of WC-Co, the tool wear in the flank face was formed bigger than that in the rake face on orthogonal micro cutting. And the machining surface integrity on the side of the cutting tool with a negative rake angle was better than that with a positive one, as well as burr in the case of using the cutting tool with a negative rake angle was formed very little compared to the that with a positive one.

• Journal of Computational Design and Engineering
• /
• 제2권4호
• /
• pp.197-205
• /
• 2015

Bladed disk (BLISK) is a vital part in jet engines with a complicated shape which is exclusively machined on a five-axis machine and requires high accuracy of machining. Poor quality of tool orientation (e.g., false tool positioning and unsmooth tool orientation transition) during the five-axis machining may cause collision and machine vibration, which will debase the machining quality and in the worst case sabotage the BLISK. This paper presents a reference plane based algorithm to generate a set of smoothly aligned tool orientations along a tool path. The proposed method guarantees that no collision would occur anywhere along the tool path, and the overall smoothness is globally optimized. A preliminary simulation verification of the proposed algorithm is conducted on a BLISK model and the tool orientation generated is found to be stable, smooth, and well-formed.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1998년도 춘계학술대회 논문집
• /
• pp.53-58
• /
• 1998

Case hardening of tool steel(SK5) was investigated after YAG laser irradiation. In the case of beam passes, martensite formed in the melt zone and in former pearlite regions of the austenization zone exhibited very high Vickers Hardness values. The molten depth and radius, micro structure, hardness were investigated as a function of defocusing distance, pulse width, and power density.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1994년도 추계학술대회 논문집
• /
• pp.67-72
• /
• 1994

Tool test was conducted to investigate the were process of only flank face TiN coated HSS tool in interrupted cutting for variuos cutting speeds and feed rates. Flank wear was caused by microchipping at the cutting edge. At high cutting speed, the which was formed as a result of diffusion and abrasion lowered cutting edge and influenced flank were. Flank wear due to chipping was little influenced by cutting speed.

• 한국정밀공학회지
• /
• 제23권1호
• /
• pp.80-88
• /
• 2006

In this study, unsintered and presintered low purity alumina ceramics were machined with various tools to clarify the machinability and the optimum cutting conditions. The main conclusions obtained were as fellows. Machined with ceramic tool, the ceramics presintered at the temperature range of $1000\~1100^{\circ}C$ showed the best machinability due to the adhesion formed in weared surface within a certain cutting speed range. In the above combination and conditions, the ceramic tool showed the highest productivity through all experiments. The life of CBN tool was longer in machining of the ceramics presintered at $1000^{\circ}C$ than in the case of that presintered at $600^{\circ}C$, but the diamond tool showed adverse tendency. In machining of the ceramics presintered at $1000^{\circ}C$, the ceramic tool exhibits the longest tool life in high speed, the tool lives became extremely worse in the order of CBN tool and diamond tool. However, in the case of the ceramics presintered at $600^{\circ}C$, the diamond tool shows the longest tool life, the tool lives was much worse in the order of CBN tool and ceramic tool.