• 제어로봇시스템학회논문지
• /
• 제11권3호
• /
• pp.228-232
• /
• 2005

This paper presents the efforts of the studies for improvement of spin characteristics of KTX-1 #02 through rotary balance test, forced oscillation test and spin mode analysis. During the full scale development design stage, we had fullfilled a lot of spin flight test, spin mode analysis. Based on all of the efforts, KTX-1 had been developed as a successful trainer with excellent spin characteristics.

• 한국군사과학기술학회지
• /
• 제3권2호
• /
• pp.81-87
• /
• 2000

This paper presents an application of forced oscillation technique to measure pitch dynamic stability derivatives of a missile model in the low speed wind tunnel. The missile model is oscillated by D.C. electric servomotor with constant amplitudes and frequencies. Phase shift is determined as the difference of peak values between input and output signals from the dynamic stability balance installed at the center of gravity of the model. Stability derivatives were calculated by using phase shifts, amplitudes, forcing moments and input frequencies. Test results show the proper usage of the force oscillation technique with good damping effects.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2002년도 추계학술대회 논문집
• /
• pp.134-141
• /
• 2002

A series of forced oscillation test on model mooring chain was carried out to investigate dynamic tension characteristics. The model test was conducted at two different water depth to gather basic data for 'truncated mooring test' and 'hybrid mooring test'. The truncated and hybrid mooring test are highly recommended to overcome the limitation of water depth in model test recently. The resultant tension RAO gives good possibility of approximation of dynamic tension by equivalent weight adjustment for the ratio of water depth in different water depth. Because the hybrid mooring test is the adequate combination of model test and simulation, accurate simulation model on mooring system is essential. The simulation results show good agreement with model test results.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2011년도 정기 학술대회
• /
• pp.332-335
• /
• 2011

바람에 의해 발생하는 장대교량의 진동현상은 버펫팅과 와류진동 그리고 플러터 등으로 구분할 수 있으며, 특히 설계풍속에 해당하는 강풍에 안전한 교량을 설계하는 것이 주된 관심사항이다. 이러한 장대교량의 공기역학적인 안정성 검토에 사용되는 플러터 계수를 풍동실험을 통하여 산정하였다. 본 논문에서는 일반적인 플레이트 거더교의 강풍에 대한 안정성을 검토하기 위하여 풍동실험을 수행하였으며, 자유진동 기법과 강제진동 기법을 사용하여 추출한 플러터 계수를 비교하였다. 자유진동 기법은 교량단면에 초기변위를 주어 상하 및 회전 진동을 하는 교량단면의 변위를 측정한 후 system identification 기법으로 플러터 계수를 구하게 된다. 그리고 강제진동 기법은 상하방향의 강제진동과 회전방향의 강제진동 실험을 독립적으로 수행하여 교량단면에 작용하는 풍하중과 단면의 진동을 분석함으로써 플러터 계수를 추정하게 된다. 그리고 플러터 계수의 비교를 통하여 강제진동 기법과 자유진동 기법의 장단점을 분석하였다.

• 한국해양공학회지
• /
• 제19권3호
• /
• pp.39-46
• /
• 2005

A series of forced oscillation tests on a model mooring chain was carried out to investigate dynamic tension characteristics. The model test was conducted at two different water depths to gather basic data for a 'truncated mooring test' and 'hybrid mooring test'. The truncated and hybrid mooring tests are important for overcoming the limitation of water depth that existed in previous model tests. The resultant tension RAO provides a good possibility of approximation of dynamic tension by equivalent weight adjustment for different water depths. Because the hybrid mooring test is an adequate combination of model test and simulation, an accurate simulation model for the mooring system is essential. The simulation results show good agreement with model test results.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2004년도 학술대회지
• /
• pp.30-35
• /
• 2004

Several roll motion reduction devices are reviewed and suggested for the application in FPSO. The firstly suggested solution is the shape of the bilge. The next is a bilge keel. The last suggestion is the ART (anti-rolling tank). Typical U-tube type ART is designed for a FPSO and examined extensively by model experiment. The model section was made of transparent acryl. Free decay test, forced oscillation test and wave test were carried out at a two-dimensional wave flume. U-tube type ART is effective only when the natural periods of ART and ship are same. Therefore, the divided U-tube type ART with split plate is suggested for the reduction of the roll motion of a FPSO over the wide range of the roll period.

• 대한조선학회논문집
• /
• 제59권4호
• /
• pp.214-224
• /
• 2022

It is necessary to estimate manoeuvring characteristics of submerged bodies at the design stage in order to ensure the safe operations. In this study, added mass coefficients in the mathematical model of submerged bodies are estimated by captive model tests and numerical calculations. Two kinds of models, MARIN 'BB2'submarine model and AUV (Autonomous unmanned vehicle) model are utilized in the forced oscillation tests. Compared to BB2 submarine, AUV with cylindrical type hull form shows relatively small added masses in roll, pitch, and yaw directions. Next, numerical calculations based on potential theory are performed under the assumption that viscous effects on inertia forces are negligible. Added masses obtained by numerical calculations are in good agreements with forced oscillation test results. And if slow manoeuvres of submerged bodies are presumed, some of velocity coupled terms can be approximated by combinations of added mass coefficients.

• 한국해양공학회지
• /
• 제30권2호
• /
• pp.91-99
• /
• 2016

The global demand for oil and natural gas has increased, and resource development is moving to the deep sea. Floating and flexible offshore structures such as semi-submersible, spar, and FPSO structures have been widely used. The major equipment of floating structures is always exposed to waves, currents, and other marine environmental factors, which cause structural damage. Moreover, flexible risers are susceptible to an exciting force due to the motion of the floating body. The inline and transverse responses from the three-dimensional behavior of a floating structure occur because of various forces. Typical risers are made of steel pipe and applied in the oil and gas development field, but flexible materials such as polyethylene are suitable for OTEC risers. Consequently, the optimal design of a flexible offshore plant requires a dynamic behavior analysis of slender bodies made of the different materials commonly used for offshore flexible risers. In this study, a three-dimensional motion measurement device was used to analyze the displacements of riser models induced by external force factors, and forced oscillation of a riser was linked to forced oscillation under a steady flow and regular wave condition.

• 한국항공우주학회지
• /
• 제31권6호
• /
• pp.17-22
• /
• 2003

비행선은 주익이 없고 미익에 비해 동체 효과가 큰 형상으로 인해 정적으로 불안정한 특성을 지닌다. 따라서 동안정 특성 예측이 매우 중요하다. 본 연구에서는 강제진동 풍동시험을 통한 비행선의 동안정 특성 자료를 확보하였다. 풍동시험은 미국 BAR사의 독일소재 시설인 BAR LAMP 시설을 사용하였으며, 16회의 정적시험과 26회의 강제진동시험을 수행하였다. 시험결과, 비행선의 동안정 특성은 받음각 뿐만 아니라 옆미끄럼각, 각속도의 크기와 방향에 비선형적으로 변한다. 전반적으로 세 방향의 모멘트는 댐핑이 있는 것으로 나타났으며, 수직력과 측력, 교차성분은 불안정하게 나타났다. 조종면의 영향은 작은 것으로 나타났으나 옆미끄럼각의 영향은 완전히 비선형적으로 나타났다.

• 한국항공우주학회지
• /
• 제44권7호
• /
• pp.552-561
• /
• 2016

본 연구에서는 강제진동 기법을 이용하여 람다형상을 갖는 무미익 무인기의 동안정 미계수를 측정하였다. 강제진동 기법은 시험모델을 일정한 크기의 각 변위로 진동시키면서 항공기에 작용하는 공력의 시간이력(time history) 데이터를 측정하고, 입력진동 대비 공력데이터의 위상차와 진폭을 추출함으로써 비행체의 동안정 미계수를 계산하는 방법이다. 본 연구에서는 롤, 피치, 요 방향으로 각각 진동시킬 수 있는 실험 장치를 설계, 제작하여 국내 최초로 무미익 항공기의 동안정 미계수 측정 시험을 수행하였다. 롤 댐핑 동안정 미계수 측정 결과, 진동 주파수와 진동의 크기가 증가하여도 동안정 미계수의 경향성은 동일하게 나타나며, 전반적으로 측정 받음각 구간에서 안정한 특성을 보였다. 피치 댐핑 동안정 미계수의 경우 작은 진동 주파수에서 동적으로 더 안정해지며, 받음각 $15^{\circ}$ 이상에서는 동적으로 불안정해지는 경향성을 보였다. 각 시험데이터들은 반복성 시험을 통해 데이터의 신뢰성을 검증하였으며, 본 연구에 적용된 강제진동 기법이 무미익 항공기의 동안정 미계수를 성공적으로 측정할 수 있음을 확인하였다.