• Journal of Magnetics
• /
• 제20권2호
• /
• pp.166-175
• /
• 2015

In this study, we describe the design method of a Brush-less DC (BLDC) motor with delta winding connection. After designing delta winding connection model with the $60^{\circ}$ flat-top region of the Back Electro-Motive Force (BEMF), an ideal current source analysis and a voltage source analysis, with a 6-step control, were conducted primarily employing Finite Element Method. In addition, as a current controller, we considered the Current Regulator with PI controller using Simulink for the comparison of torque characteristics. When the input current is controlled, the switching regions and reference signals are determined by means of the phase BEMF zero-crossing point. In reality, the input current variation depends on the inductance as well as input voltage, and it causes a torque ripple after all. Therefore, each control method considered in this research showed different torque ripple results. Based on the comparison, the causes of the torque ripple have been verified in detail.

• International journal of advanced smart convergence
• /
• 제9권4호
• /
• pp.26-33
• /
• 2020

This study measured the downward stepping movement relative to weight change (no load, and 10%, 20%, 30% of body weight respectively of adult male (n=10) from standardized stair (rise of 0.3 m, tread of 0.29 m, width of 1 m). The 3-dimensional cinematography and ground reaction force were also utilized for analysis of leg stiffness: Peak vertical force, change in stance phase leg length, Torque of whole body, kinematic variables. The strategy heightened the leg stiffness and standardized vertical ground reaction force relative to the added weights (p<.01). Torque showed rather larger rotational force in case of no load, but less in 10% of body weight (p<.05). Similarly angle of hip joint showed most extended in no-load, but most flexed in 10% of body weight (p<.05). Inclined angle of body trunk showed largest range in posterior direction in no-load, but in vertical line nearly relative to added weights (p<.001). Thus the result of the study proved that downward stepping strategy altered from height of 30 cm, regardless of added weight, did not affect velocity and length of lower leg. But added weight contributed to more vertical impulse force and increase of rigidity of whole body than forward rotational torque under condition of altered stepping strategy. In future study, the experimental on effect of weight change and alteration of downward stepping strategy using ankle joint may provide helpful information for development of enhanced program of prevention and rehabilitation on motor performance and injury.

• 대한기계학회논문집A
• /
• 제21권6호
• /
• pp.871-883
• /
• 1997

Kinetodynamics of a cam driving slider mechanism consists of kinematic analysis and force analysis. The kinematic analysis is to determine the kinematic characteristics of a cam driving mechanism and a slider mechanism. The force analysis is to determine the joint forces of links, the contact forces of the cam and follower, and the driving torque of a main shaft. This paper proposes a close loop method and a tangent substitution method to formulate the relationships of kinematic chains and to calculate the displacement, velocity and acceleration of the cam driving slider mechanism. Also, and instant velocity center method is proposed to determine the cam shape from the geometric relationships of the cam and the roller follower. For dynamic analysis, the contact force and the driving torque of the cam driving slider mechanism are calculated from the required sliding forces, sliding motion and weight of the slider.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문초록집
• /
• pp.380.2-380
• /
• 2002

SRM(Switched Reluctance Motor) 내부의 Radial Force는 소음ㆍ진동의 주원인이 되는 가진력으로 작용하는 것으로 알려져 있다. 따라서 본 논문에서는 Radial Force의 주 요인인 Motor 내부의 Air Gap 편심에 따른 반경방향의 전자기 가진력을 전자장 수치해석을 통하여 해석하고 소음ㆍ진동에 미치는 영향을 분석하였다. Air Gap 편심량을 변화시켜 가면서 Stator, Rotor의 Local Force와 Gloval Force인 Torque Fluctuation을 해석하고 이를 실험 결과와 비교함으로서 해석결과의 타당성을 입증하였다.

• 대한치과교정학회지
• /
• 제35권2호
• /
• pp.137-147
• /
• 2005

본 연구는 상악 절치부에 active 토크가 가해졌을 경우, 교정력을 직접 받은 치아와 인접 치아의 반응을 알아보고자, 상악 치아 및 치조골의 유한요소 모델을 제작하고, stainless steel NiTi, TMA 세 종류의 각형 호선을 육면체 요소로 모델링하여 유한요소 모델을 완성하였다. 호선이 브라켓에 삽입되었을 때 브라켓에 발생하는 반력과 모멘트를 구하였고, 이것을 유한 요소 모델에 적용하여 각 치아의 변위와 응력 분포를 측정하였다 브라켓에 발생하는 반력은 근원심 방향과, 협설 방향으로의 힘은 0에 가까우며, 중절치, 측절치, 견치의 브라켓 근심측에서는 정출력이 원심측에서는 압하력이 발생하였다. 힘과 모멘트의 크기는 측절치에서 최대였고 중절치. 견치 순으로 감소하였고, 소구치 부위와 대구치 부위에서는 급격히 감소하였다. 중절치와 측절치는 치관 협측, 원심 경사 이동과 압하를 보였으며 견치는 치관 설측 원심 경사와 정출을 보였고. 제1소구치는 치관 설측 경사이동을 보였다. $019\times025SS$을 사용하여 상악 절치부에 토크를 부여하는 경우에는 측절치에 과도한 힘이 집중되므로, 임상에서 토크를 조절 할 경우에는 NiTi나 TMA 호선을 사용하는 것이 바람직하리라고 생각된다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2009년도 제40회 하계학술대회
• /
• pp.895_896
• /
• 2009

this paper presents a rotor shape optimization of interior type permanent magnet (IPM) motor for vibration minimization. the vibration of permanent magnet motor is generated by cogging torque, radial force and commutation torque ripple which are electromagnetic source of vibration. In order to minimize the vibration, the optimal notches are put on the rotor pole face and the arc type pole face is applied. The variations of cogging torque and radial force of each model vibration frequency are computation by finite element method (FEM) and the validity of the analysis and rotor shape design is confirmed by vibration experiments.

• 소음진동
• /
• 제7권3호
• /
• pp.467-475
• /
• 1997

A rotor-bearing system has been investigated, including internal damping and axial torque using finite dynamic elements. A procedure is presented for dynamic modeling of rotor-bearing system which consist of finite dynamic shaft elements, rigid disk, and bearing and seal. A finite dynamic element model including the effects of rotatory inertia, gyroscopic moments, axial force, and axial torque is developed using the frequency dependent shape function. The natural whirl speeds, stability, and unbalance response of rotor system are calculated on several cases and compared with the conventional finite elements.

• 전기학회논문지
• /
• 제65권2호
• /
• pp.298-303
• /
• 2016

In this paper, the vibration source of IPM type BLDC motor was analyzed by finite element method. The main causes of the electrical vibration were RMF(Radial magnetic force) and cogging torque. It was designed model of minimized cogging torque and RMF equilibrium. Design models were selected the optimum model using the design of experiment method. And, the vibration experiment was carried out through prototype machine of each model. Finally, the experimental results were compared with the analysis ones.

• 한국소음진동공학회논문집
• /
• 제23권2호
• /
• pp.144-151
• /
• 2013

This paper presents a result of the mechanical noise and vibration analysis as well as the electrical characteristics analysis of the permanent magnet(PM) motor according to the driving method that is Brushless DC(BLDC) drive and Brushless AC(BLAC) drive. To do that, the characteristics of the PM motor, which have the same output power but different driving method, are investigated. At that time, the characteristics such as torque, torque ripple and flux density, and so on, are obtained by finite element analysis(FEA). Besides, noise and vibration are obtained by spectrum analysis. The magnetic noise is defined as noise generated from vibrations due to electromagnetic excitation force. In this paper, the electromagnetic excitation force is analyzed and design process of noise reduction is proposed. Finally, The validity of the analysis results is verified by test.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 하계학술대회 논문집 B
• /
• pp.596-598
• /
• 2001

This paper presents an analysis of the characteristics in switched reluctance motor (SRM). 2D finite element method (FEM) considering the iron saturation and the actual switching circuit of the SRM drive is applied for the dynamic analysis. The influence of the rotor shape on the radial force and torque ripple is investigated and the optimal shape of rotor pole is proposed to enhance the torque. The radial force characteristics acting on the surface of teeth is investigated by using the Maxwell's magnetic stress tensor method.