• 한국소음진동공학회논문집
• /
• 제26권2호
• /
• pp.121-129
• /
• 2016

The noise pattern of a household refrigerator is dependent on the characteristics of its operating cycle which is repeated with a specific pattern depending on various parameters, such as room temperature and performance of its mechanical parts. Analysis of noise pattern is essential prior to evaluation of sound quality of a refrigerator. In this study, 14 units of refrigerator were classified into 4 types according to noise pattern and sort of mechanical part, which helps to analyze characteristics of refrigerator noise. Sound quality metrics(loudness, sharpness, roughness, and fluctuation strength) were calculated to compare noise pattern of the 4 types of refrigerator. The results of this study can be useful to decide noise performance of refrigerator.

• 조명전기설비학회논문지
• /
• 제30권2호
• /
• pp.78-84
• /
• 2016

This paper is focused on the measurement and analysis of an atmospheric electric field which is caused by thunderclouds. The electric field due to thunderclouds changes very slowly. For this reason, the extremely low frequency E-field sensor needs to be used for measuring the atmospheric electric field strength. The balloon-carried E-field sensor system with the time constant of 1sec was designed and fabricated. The electric field sensor consists of $100mm{\times}100mm$ copper plate, active integrator, high pass and low pass filters and batteries. The measurements of atmospheric electric fields were made by the balloon-carried E-field sensor and radiosonde, which sends the data back to ground in real time. From the calibration experiments, the response sensitivity of the E-field sensor was 0.154mV/kV/m in the frequency range of less than 1kHz. As a result from the actual experiment of the atmospheric electric field, the electric field signals were observed from the altitude of about 2.5km. Also, as the altitude was increased, the detected electric field wave oscillated with the fluctuation of sensing plate. The proposed method seems suitable for measurements of atmospheric electric fields, because it is inexpensive, simple to use and launch.

• 대한기계학회논문집B
• /
• 제31권7호
• /
• pp.644-652
• /
• 2007

In this paper, a technique of simultaneously measuring the velocity and the temperature in micro-scale flow is proposed. This method uses particle tracking velocimetry (PTV) for measuring the velocity and laser induced fluorescence (LIE) for measuring the temperature. To measure the accurate velocity and temperature, images for PTV and for LIE are separated by using two light sources and a shutter which is synchronized with a camera. By using only one camera, measurement system can be simplified and the error from complicate optical system can be minimized. Error analyses regarding the concentrations of fluorescent dye and particle and the light source fluctuation are also conducted. It is found that the error of the temperature and the velocity highly depends on the concentration of fluorescent particles which are used for PTV. This technique is applied to the simultaneous measurement of the velocity and the temperature in the electrokinetic flow. It is found that the velocity and temperature vary with the electric field strength and the concentration of electrolyte.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 1993년도 Proceedings of International Conference for Agricultural Machinery and Process Engineering
• /
• pp.830-839
• /
• 1993

Agricultural hydraulic robot which was reported in Part Ⅰ had been developed . The robot satisfied performance to intend before development. For actual use, however, it have been necessary to reduce manipulator weigh and to simplify construction of hydraulic control valve. Then, working stress of manipulator link and pressure fluctuation of hydraulic circuit were measured. Step and frequency response tests were done subject to amplitude of reference voltage of 0.1 , 0.3 , 0.5 and 1.0v. and delivery pressure of 3.5 and 5.0MPa. Working stress were about 25% comparing with fatigue strength, Thus, mass of manipulator might be reduce to 30 %. In hydraulic control system, virtual natural frequency of 6.5Hz is produced from the combination of drain passage area shortage of servovalve. Further , because of passage area shortage , working pressure at both side of cylinder was acted on. This phenomenon prevent utilize effectively engine power. Then, control valve for new model was p oposed.

• 한국음향학회지
• /
• 제19권7호
• /
• pp.15-22
• /
• 2000

본 연구에서는 수중표적의 반사신호를 재현하기 위한 공간적 하이라이트 분포처리 알고리듬을 제안한다. 제안된 알고리듬은 입사되는 핑펄스의 각도에 따라 가변적인 불연속 하이라이트와 표적내부 및 특정위치의 하이라이트를 신호 입사각에 따라 분포시켜 합성한다. 완성된 UTAHID 모델은 핑펄스의 입사각도 및 펄스폭에 따라 첨두치 표적강도, 에너지 표적강도, 에코신장효과, 표적 시간분산 손실 및 포락선의 불규칙성 등을 각종 모의실험으로 타당성을 확인하였으며, 이는 능동소나의 표적 반사신호 합성에 관련된 각종 실제 시스템에 효율적으로 적용될 수 있다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2009년도 춘계학술대회 논문집
• /
• pp.145-148
• /
• 2009

연료 과농 가스발생기의 연소시험이 파워팩 환경에서 수행되었다. 가스발생기는 파워팩 환경에서 특성 길이 증가로 인해 축 방향 연소 불안정에 취약하다. 가스발생기 후단에 압력 강하를 위해 삽입한 오리피스는 축 방향 연소 안정성을 향상시켜주는 것으로 확인되었다. 연소실과 추진제 매니폴드에서 측정한 압력 섭동의 세기는 연소실 압력의 제곱에 비례하여 증가하였다. 특히 연료 매니폴드 내의 압력 섭동이 산화제 매니폴드 또는 연소실 압력 섭동보다 약 2배 이상 크게 발생하였다. 주파수 분석 결과, 연료 매니폴드 압력 섭동은 비선형적인 특성을 내포하고 있는 것으로 파악되었다.

• 한국환경과학회지
• /
• 제25권11호
• /
• pp.1521-1530
• /
• 2016

As a result of dividing typhoon that affected Korean Peninsular between 1999 and 2012 into 7 types of path and entering forecast field and analysis field of RDAPS, until 36 hours from the time of forecast, it is reliable to use the forecast field of RDAPS to predict typhoon and for each typhoon path, the difference between the forecast and the analysis shows normal distribution, which is usable for weather forecast until the $36^{th}$ hour. In the $48^{th}$ hour from the time of forecast, the difference of result depending on each typhoon path increased, which was analyzed to be due to errors in the forecast. It was expected that relatively reasonable results should be shown if the $36^{th}$ hour forecast is used to predict the strength and distribution of strong wind. As a result of using Korean RAM and observing the difference of the maximum damage, reliability was secured up to 36 hours and after 48hours, it was expected that the fluctuation of results may become more severe.

• Journal of Welding and Joining
• /
• 제29권1호
• /
• pp.107-114
• /
• 2011

CP steel was developed to reduce the weight and increase the strength of car body. When it was welded using state-of-the-art disk laser welding, the effected of boron on the microstructure and hardness were investigated. Welding power was fixed at 3.5kW and welding speeds were 4,8 and 12m/min. Full penetration occurred in welding speed of 12m/min and weld bead was almost unchanged with boron contents. But the welding speed increased, the upper and lower bead were narrowed. In a welding speed of more than 8m/min, underfill defects were formed on the bead bottom. The hardness of weld zone was somewhat fluctuation in fusion zone and HAZ showed the highest hardness values. The hardness of each region showed little change with the boron contents, and softening phenomenon occurred in the HAZ near the base metal regardless of the boron contents.

• 대한기계학회논문집B
• /
• 제23권5호
• /
• pp.603-609
• /
• 1999

The effect of an external acoustic excitation on the wake structure behind a circular cylinder was experimentally investigated. The sound wave was excited in the frequency range of the shear layer instability and two sound pressure levels of 114 and 120dB were used in this study. As a result, the acoustic excitation modified the wake structure by increasing the velocity fluctuation energy without changing the vortex shedding frequency. The acoustic excitation enhanced the vortex shedding process and promoted the shear layer instability. Consequently, the acoustic excitation reduced the length of the vortex formation region and decreased the base pressure. In addition, the vortex strength of vortices was increased and the width of the wake was spread out due to the acoustic excitation. When the excitation frequency was identical to the shear layer instability frequency, the effect of the external flow control on the cylinder wake was maximized. In addition, with increasing the sound pressure level, the effect of the external acoustic excitation on the wake structure increased.

• 한국감성과학회:학술대회논문집
• /
• 한국감성과학회 2002년도 춘계학술대회 논문집
• /
• pp.24-29
• /
• 2002

The purpose of this study was to classify apparel fabrics according to rustling sounds and to analyze their transformed colors and mechanical properties. The rustling sounds of apparel fabrics were recorded and then transformed into colors using Mori's color-transforming program. The specimens were clustered into five groups according to sound properties, and each group was named as 'Silky', 'Crispy', 'Paper-like', 'Worsted', and 'Flaxy', respectively. The Silky consisted of smooth and soft silk fabrics had the lowest value of LPT, $\Delta$f ARC, loudness(z) and sharpness(z). Their transformed colors showed lots of red portion and color counts. The Crispy with crepe fabrics showed relatively low loudness(z) and sharpness(z), but diverse colors and color counts were appeared. The Paper-like showed the highest value of LPT, $\Delta$f and loudness(z). The Worsted composed of wool and wool-like fabrics showed high values of LPT, $\Delta$f loudness(z) and sharpness(z). The transformed colors of the Paper-like and Worsted showed the blue mostly but color counts were less than the others. The Flaxy with rugged flax fabric had the highest fluctuation strength, and their transformed colors showed diversity.