• Journal of the Korean Chemical Society
• /
• v.53 no.1
• /
• pp.27-33
• /
• 2009

A sensitive technique for the determination of trace Cd(II) in various real samples after preconcentration onto microcrystalline p-dichlorobenzene loaded with 2-mercaptobenzothiazole was developed. Several experimental conditions such as the pH of the sample solution, the amount of chelating agent 2-mercaptobenzothiazole, the amount of adsorbent p-dichlorobenzene-2-MBT, and the flow rate of sample solution were optimized. The interfering effects of various concomitant ions were investigated. Cu(II) interfered with more seriously than any other ions. However, the interference by Cu(II) could be overcome sufficiently by adjusting tartrate ion concentration to be 0.01M or by controlling the amount of 2-mercaptobenzothiazole contained in 0.20 g p-dichlorobenzene to be 0.12 g. The dynamic range, the correlation coefficient ($R^2$) and the detection limit obtained by this proposed technique were $0.5{\sim}30$ ng $mL^{-1}$, 0.9962, and 0.39 ng $mL^{-1}$, respectively. Thus, good results were obtained by the use of p-dichlorobenze as adsorbent matrix. For validating this proposed technique, the aqueous samples(wastewater, stream water, and reservoir water) and the plastic sample were used. Recovery yields of $93{\sim}104$ % were obtained. By F test, these measured data were not different from ICP-MS data at 95 % confidence level. Based on the results from the experiment, it was found that this proposed technique could be applied to the preconcentration and determination of Cd(II) in various real samples.

• Journal of Korea Water Resources Association
• /
• v.36 no.3 s.134
• /
• pp.507-520
• /
• 2003

A V-shaped riffle is an artificial hydraulic structure haying two wings from the streamside with a narrow opening in between. It is usually made of crushed stones or large boulders. It limits channel width and accelerates the flow through the constricted section causing a local scour just downstream. The V-shaped riffle provides with a unique aquatic habitat by forming a pool and sandbars around the pool edge, increasing local morphologic, hydraulic and sedimentological diversity. This study investigates experimentally the scour characteristics of the V-shaped riffle in the sandbed stream and proposes a predictive equation for the scour. Total 45 cases of experiments were conducted to examine the effect of hydraulic factors and configuration of V-shaped riffle on the geometry of scour holes. From the comparison of the experimental results of this study with the predictive equation of spur dike by Breusers and Raudkivi(1991), it is found that their predictive equation of spur dike underestimates the maximum scour depth downstream of the V-shaped riffle. h new predictive equation for the maximum scour depth was developed using the non-dimensional hydraulic and geometrical variables. The parameters used in the proposed equations were determined using the experimental data. The analysis reveals that the scour depth is dependent dominantly on the Froude number at the opening of the V-shaped riffle, while the angle of riffle and the opening width also affect the scour depth. The proposed equation for the scour of V-shaped riffle well agrees with the experimental data. It can be used for estimating the scour of the V-shaped riffle in sandbed streams.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2004.04a
• /
• pp.100-101
• /
• 2004

Many researches in Korea have been performed to understand the pollution of stream waters by acid mine drainage. However, few studies have been conducted regarding the effect of particulate and colloidal fractions on the transport of trace metals. To estimate harmful effects of trace metals, it is important to evaluate the particulate and colloidal metals as well as dissolved metals, because particulate and colloidal fractions of trace metals play an important role in transport of trace metals and may adversely affect habitats and organisms in riverine system. Colloids are solids with effective diameters in size range from 0.001 $\mu$m to 1 $\mu$m. According to Jone et al. (1974), metals in surface water, like Al, Fe, and Mn, require filtration with pore-size membranes smaller than 0.45 $\mu$m to define dissolved concentrations. The main objective of this study is to understand the effects of particulate, colloidal, and truly dissolved fractions on the transport and fate of trace metals in acid mine drainage. This study was conducted for the Onjeong creek in the Uljin mine area. Sampling was carried out in 13 sites, spatially covering the area from mine dumps to the downstream Onjeong reservoir. To examine the metal partitioning between particulate, colloidal, and truly dissolved fraction, we used successive filtration techniques consisting of conventional method (using 0.45 $\mu$m membranes) and tangential-flow ultrafiltration (using 0.001 $\mu$mm membranes). Ultrafiltration may seperate much smaller particles from aqueous phase (Josephson, 1984; Hernandez and Stallard, 1988). The analysis of metals were performed by inductively coupled plasma - atomic emission spectrometer (ICP-AES: model Perkin Elmer OPTIMA3000XL). Anions such as SO$_4$, Cl and NO$_3$ were measured with ion chromatograph (IC: model Dionex 120). Sample analysis is still in progress. The preliminary data show that the studied creek is severely polluted by Al, Fe, Mn, Pb and Zn. Toward upstream sites with relatively lower pH, less than 50% of Al and Fe occur in the sorbed form on particles or colloids, whereas more than 80% of Al and Fe occur in the sorbed form in downstream sites or tributaries with relatively higher pH. Less than 30% of Zn is present in particle or colloidal forms in the whole range of creek. Truly dissolved fraction of trace metals is negatively correlated with pH. The Kd values for Al, Fe and Zn consistently increase with increasing pH and decrease with increasing particle concentration.

• Journal of Soil and Groundwater Environment
• /
• v.14 no.1
• /
• pp.1-10
• /
• 2009

Groundwater flow due to intake of horizontal collector well in riverbank filtration site was analyzed by use of numerical groundwater modeling program (FEFLOW 5.1). Drawdowns of groundwater table nearby collector well were evaluated according to variations of several conditions; pumping rate, thickness of aquifer, offset distance from well to shore line of stream, conductance of streambed. It is observed that the drawdowns of groundwater table are clearly changed according to the variations of these conditions. The results of sensitive analysis shows that the thickness of alluvial aquifer and the offset distance are more sensitive than the conductance of streambed in evaluation of drawdown. This result implies that hydrogeological conditions, as like thickness of aquifer and its distribution in the site are important factors in site selection and evaluating the availability of riverbank filtration intake using horizontal collector well system. It is also revealed that numerical modeling using FEFLOW with 1-D discrete element feature can give efficient quantitative evaluation of horizontal collector well and estimation of availability of riverbank filtration site.

• Journal of Korean Society of Water and Wastewater
• /
• v.22 no.1
• /
• pp.121-129
• /
• 2008

Major factors affecting water quality in rivers are transportation, input of pollutant loads and kinetic transformation of pollutants. Government level decision makings on water quality management are based on steady state water quality modeling. However, it is more than often that such a steady state assumption is far from real situations in rivers. Therefore, it is unavoidable to have modeling errors in water quality modeling especially for steady state modeling for longer period of time. Authors attempted to identify sources of errors in results of steady state models and thus tried to find out ways to minimize those errors. Three water quality models, QUAL2E (Brown et al., 1983), QUAL2K (Chapra et al., 2006) and CAP (Seo and Lee, 2000) were applied to the lower stream of the Geum River. $BOD_5$ and COD tend to underestimate observed data while TN and TP showed relatively smaller errors. QUAL2E model provided best calibration results for BOD5 and TP and QUAL2K model showed best calibration results for TN. Since these errors are only relative values, it was difficult to conclude which model is better performing in certain situations. The most probable reasons for errors in water quality modeling are; 1) inappropriate consideration on flow characteristics, 2) lack of information on incoming pollutant load and 3) inappropriate location of sampling for water quality analysis.

• Journal of Korea Water Resources Association
• /
• v.36 no.6
• /
• pp.925-936
• /
• 2003

The objective of this study is to suggest new drawing methods of isochrones using GIS. For this purpose the Unit Hydrograph (UH) of studied watershed for instantaneous rainfall suggested by Clark have been determined by routing the time-area curve through a single linear reservoir. To evaluate constructing methods of isochrones three methods has been examined; Channel Profile and Clark-kict method; Laurenson method; Average velocity method of S.C.S. Also, these methods have been recomposed by GIS in this study. To apply first method, spatial modeling, the vector based on the stream network and Route_System measuring a distance between points has been used. A raster based on the flow direction grid from burn DEM and the slope grid from original DEM has been applied for the second method. The third method has been applied by a raster based on the landuse grid and a velocity function expressed by slope. Results by these three methods have been evaluated with observed hydrograph, and the method using average velocity method of S.C.S shows more reasonable results comparatively.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2006.05a
• /
• pp.1686-1690
• /
• 2006

현재 우리나라에서는 하천의 개수사업 및 교량, 제방 등과 같은 수공구조물 설계시 계획 홍수위를 산정하는데 있어 실무에서는 1차원 모형인 HEC-RAS 모형이 널리 이용되고 있다. 그러나 HEC-RAS 모형과 같은 1차원 모형의 경우 모형의 한계로 인해 하폭의 확대, 축소, 만곡부 및 섬 등과 같은 장애물 존재시 하천횡단면에 따른 수위 및 유속변화를 표현하는데 많은 어려움이 있으며, 이런 한계로 인해 1차원 모형만을 이용하여 하도 및 하천공간계획을 수립하기란 사실상 불가능하다. 또한 최근 들어 하천기능에 대한 인식이 과거 홍수소통, 용수이용 등 이.치수중심에서 인간과 다양한 생명체가 공존하는 서식처로서의 기능을 부여하는 생태하천의 개념으로 변화하는 추세이며, 이와 같이 변화된 패러다임하에서 생태하천복원사업 등과 같은 하천관련 사업추진 시 합리적인 하도 및 하천의 공간계획을 수립하기 위해서는 하도내 2차원 흐름특성 등과 같은 기초자료가 절실히 요구된다. 따라서, 본 연구에서는 합리적인 하도 및 하천의 공간계획을 수립하기 위한 기초자료를 제공함은 물론, 보 철거에 따른 하도내 흐름개선 효과를 분석하기 위해 연구대상 하천인 두계천에 대하여 2차원 수치모의를 통한 하도내 흐름특성 변화를 조사하였다. 본 연구에서 선정한 2차원 모형으로는 유한요소법에 기반을 둔 RMA-2모형의 범용프로그램인 SMS 모형을 선정하였고, 1차원 수치해석을 통하여 선정된 하류단의 경계조건을 적용하여 2차원 수리특성 분석을 실시하였다. 분석결과 철거대상 취수보 15개에 대하여 보철거 후 수위에 대한 개선 효과는 금암보를 제외한 대부분의 보 철거 구간에서는 그리 크지 않은 것으로 나타난 반면, 보 철거에 따른 유속의 개선효과는 대부분 큰 것으로 나타났다.는 경우보다 낮게 나타나고 있다. On-Line 저류지의 경우 Off-Line 의 경우에 비해 수위, 유량이 저류지의 상류단에서 크게 나타났다. On-Line 저류지의 경우 Off-Line 의 경우에 비해 같은 값의 첨두홍수량을 저류하기 위해서 상대적으로 넓은 저류면적이 필요한 것으로 나타난다. 대등한 수위감소값의 홍수저감효과를 발휘하기 위해서 본 연구에서는 On-Line 저류지 면적은 Off-Line 저류지에 비 두배 이상이 필요한 것으로 보여졌다.들에 관한 정보는 종종 현장관측에서 조차 무시되는 경우가 많다. 이에 본 연구에서는 수질모형의 매개변수 중 특히 수리특성에 관련된 매개변수들이 수질에 미치는 영향을 파악하는 것을 목적으로 하고 있다. 이를 위해 적용된 수질모형은 QualKo를 사용하였으며, 대상 하천은 낙동강 본류 경남구간 시점 부근인 회천 합류 전부터 낙동강 본류 경남구간 종점 부근인 밀양강 합류 전까지의 경남 오염총량관리 기본계획 시 구축된 모형 매개변수를 바탕으로 분석을 수행하였다. 일차오차분석을 이용하여 수리매개변수와 수질매개변수의 수질항목별 상대적 기여도를 파악해 본 결과, 수리매개변수는 DO, BOD, 유기질소, 유기인 모든 항목에 일정 정도의 상대적 기여도를 가지고 있는 것을 알 수 있었다. 이로부터 수질 모형의 적용 시 수리 매개변수 또한 수질 매개변수의 추정 시와 같이 보다 세심한 주의를 기울여 추정할 필요가 있을 것으로 판단된다.변화와 기흉 발생과의 인과관계를 확인하고 좀 더 구체화하기 위한 연구가 필요할 것이다.게 이루어질 수 있을 것으로 기대된다.는 초과수익률이 상승하지만, 이후로는 감소하므로, 반전거래전략을 활용하는 경우 주식투자기간은 24개월이하의 중단기가 적합함을 발견하였다. 이상의 행태적 측

• Journal of Wetlands Research
• /
• v.13 no.3
• /
• pp.443-453
• /
• 2011

This research aims at suggesting the mitigation measures of decreasing pollution by analyzing land cover characteristics according to subwatershed, and non-pollutant load characteristics occurring in each subwatershed. Mushim-cheon is selected as a research area, and HyGIS-SWAT is used as a water quality model. This research analyzed outflow load characteristics by classifying land cover, which has over 50% classified items, into a city area, a farmland area and a forest area. The result shows that the yearly occurrence load quantity represents a farmland area, a forest area and a city area in order. In subwatershed-2, occurrence load quantity is analyzed by setting up a buffer zone in the center of stream, and by changing a farmland area into a natural grass land. Therefore, a farmland area in a subwatershed changes 36.6% into 27.9% and 15.3% comparing to previous land cover change. In the analysis of sediment loads occurrence quantity and nutritive salt load occurrence quantity in subwatershed-2, sediment loads occurrence quantity decreases 52% to about 47%, and nutritive salt load decreases 49% and 34% in compare with previous change. Hereafter, this research will set up the mitigation measures scenario, and find out which is more effective for the mitigation measures.

• Journal of Korea Water Resources Association
• /
• v.45 no.11
• /
• pp.1131-1141
• /
• 2012

In this study, factors that influence water supply capacities of dams are extracted using factor analysis, and multiple regression equations for estimating water supply capacities of dams are developed using the analysis results. Twenty-one multi-purpose dams and twelve Municipal and Industrial (M&I) water supply dams are selected for case studies, and eight variables influencing water supply capacities of dams, namely: watershed area, inflow, effective reservoir storage, grade on amount of M&I water supply, grade on amount of agricultural water supply, grade on amount of in-stream flow supply, grade on river administration, and grade on average rainfall, are determined. Two case studies for multi-purpose dams and M&I water supply dams are performed, employing factor analysis, respectively. For the two cases, preliminary tests, such as reviewing matrix of correlation coefficient, Bartlett's test of sphericity, and Kaiser-Meyer-Olkin (KMO) test, are conducted to evaluate the suitability of the variables for factor analysis. In case of multi-purpose dams, variables are grouped into three factors; M&I water supply dams, two factors. The factors are rotated using Varimax method, and then factor loading of each variable is computed. The results show that the variables influencing water supply capacities of dams are reasonably selected and appropriately grouped into factors. In addition, multiple regression equations for predicting the amounts of annual water supply of dams are established using the factor scores as explanatory variables, it is identified that the models' accuracies are high, and their applications to determining effective storage capacity of a dam during dam planning and design steps are presented. Consequently, it is thought that the variables and factors are useful for dam planning and dam design.

• Journal of Energy Engineering
• /
• v.15 no.1 s.45
• /
• pp.52-59
• /
• 2006

This paper examined the conversion of methane to hydrogen and other higher hydrocarbons using dielectric barrier discharge with AC pulse power. Two metal electrodes of a coaxial-type plasma reactor were separated by gas gap and an alumina tube. The inner electrode was located inside the alumina tube. The alumina tube was located inside the stainless steel tube, which was used as the outer electrode. Effect of feed gas composition (methane, oxygen, argon, water and helium), flow rate, applied frequency, input volt-age on methane conversion and product distribution were studied. The major products of plasma chemical reactions were ethylene, ethane, propane, buthane, hydrogen, carbon monoxide and carbon dioxide. The increment of applied voltage and the usage of inert gas as the background (helium and argon) enhanced the selectivity of hydrocarbons and methane conversion. The addition of water in the feed stream enhanced the conversion of methane and yield of hydrogen. Higher voltage leads to higher yield of $C_2H_6,\;C_3H_8,\;C_4H_{10}$ and yield or $C_2H_2\;and\;C_2H_4$ appeared highly in lower voltage.