• Journal of computational fluids engineering
• /
• v.3 no.2
• /
• pp.39-51
• /
• 1998

This paper describes the analysis of flow field around an automobile. The governing equations of the 3-D unsteady incompressible Navier-Stokes equations are solved by the iterative time marching scheme. The Chimera grid technique has been applied to efficiently simulate the flow around the side-view mirror. To validate the capability of simulating the flow around a ground vehicle, the flows around the Ahmed body with 12.5$^{\circ}$ and 30$^{\circ}$ of slant angles are simulated and good agreements with experiment and other numerical results are achieved. To validate Chimera grid technique, the flow field around a cylinder was also calculated. The computed results are also well agreed with other numerical results and experiment. After code validations, the flow phenomena around the ground vehicle are evidently shown. The flow around the side-view mirror is also well simulated using the Chimera grid technique.

• Journal of computational fluids engineering
• /
• v.4 no.3
• /
• pp.1-11
• /
• 1999

This paper describes the flow field analysis of an automobile with crosswind effects of 15°, 30° 45° and 60° of yaw angles. The governing equations of the 3-D incompressible Navier-Stokes equations are solved by the iterative time marching scheme. The Chimera grid technique has been applied to efficiently simulate the flow around the side-view mirror. The computated surface pressure coefficients have been compared with experimental results and a good agreement has been achieved. The A- and C-pillar vortex and other flow phenomena around the ground vehicle are evidently shown. The variation of aerodynamic coefficients of drag, lift, side force and moments with respect to yaw angle is systematically studied.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.1
• /
• pp.75-83
• /
• 2001

In this paper, numerical analysis is used to find the effects of inclination of rear end on flow characteristic around an automobile. The reference slant angle of rear end is 28.6$^{\circ}$, the slant angle of rear end is decreased to 24$^{\circ}$, 26.6$^{\circ}$ and also increased to 31.6$^{\circ}$, 36.4$^{\circ}$. The 3-D incompressible Navier-Stockes equations are solved by the iterative time marching scheme. The computed surface pressure coefficients were compared with experimental results and a good agreement has been achieved. The A- and C-pillar vortex and other flow phenomena around the ground vehicle are evidently shown. The variation of aerodynamic coefficients of drag, lift with respect to inclination angle of rear end are systematically studied. The flow characteristic on the automobile surface with respect to change of inclination of rear end have been also studied.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.4
• /
• pp.101-107
• /
• 1998

A three-dimensional multi-phase flow is simulated around a smooth tire. This simulation is conducted by solving Navier-Stokes equation with a k-$\varepsilon$ turbulent model. The numerical calculations are carried out by modeling a multi-phase free surface flow mixed with air and water at the inlet. The numerical solutions show an intuitively resonable behavior of water around a moving tire. The calculated pressure around the tire surface along the moving direction is presented. The moving velocities of the tire are chosen to be 30, 40, 60, and 70 km/h. The numerically simulated pressures around the tire are compared with existing experimental data. The comparison shows a new possible tool of analyzing a hydroplaning phenomenon for an automobile tire by means of a computational fluid dynamics.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.2
• /
• pp.84-91
• /
• 2001

To investigate the aerodynamic characteristics of the on a road vehicle, experimenrs were performed at an Atmospheric Boundary Layer Wind Tunnel. The scaled model of an automobile with 1 : 3 scaling ratio was used. The Reynolds number based on the free stream velocity and model length was $7.93{\times}10^5$. The influence of crosswind to the stability of automobile was investigated by the pressure distribution measurements and flow visualization studies. with the variation of the angle of attack, the change in pressure coefficient depends highly on the flow separation regimes. The experimental and numerical results are compared and found to be in good agreements.

• Journal of Aerospace System Engineering
• /
• v.2 no.2
• /
• pp.46-50
• /
• 2008

Aerodynamic characteristics, such as drag and lift, play an important role in automobile design under certain speed conditions. Such characteristics are essential to design an automobile since they are directly related to automobile's performance such as passenger safety and fuel consumption. There is a huge demand for the automobile to have safe performance at high speed. Reduction in drag is also important and it could lead to the solution of air flow induced noise and dust problems. The objective of this research is to find out the aerodynamic differences between conventional side mirror and a modified one using CFD. Although drag generated around a side mirror is only about 7% of the total drag when a car runs, it is very closely related to driver's field of vision and noise generation. CFD simulation of the flowfield around a car side-view mirror was performed using a commercial code; Gambit and FLUENT.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.3
• /
• pp.187-198
• /
• 1996

In this study, the performance of an automobile heat storage system using PCM is numerically simulated. For the analysis of system performance. The phase-change of the PCM and the transient forced convective heat transfer for the HTF are considered simultaneously as a conjugate problem. The phase-change behavior is effectively analyzed using a concept of thermal resistance. From the correlations of phase change rate and heat transfer due to the variations of flow rate of HTF around PCM, the automobile heat storage system performance is predicted. The present results amy be used as the fundamental information for the design of automobile heat storage system.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.21 no.5
• /
• pp.700-712
• /
• 1997

The flowfield generated by a 2-D rotating cylinder on a plane moving at freestream velocity was experimentally investigated in a wind tunnel to simulate aerodynamic characteristics of rotating wheels of an automobile. In the flowfield around a rotating cylinder at 3*10$^{3}$ < Re$_{d}$<8*10$^{3}$, unique mean flow and turbulence characteristics were confirmed by hot-wire measurements as well as frequency analysis, which was supported by flow visualization. In the vicinity of a rotating cylinder, a unique turbulence structure on .root.over bar u'$^{2}$ profiles was formed in hump-like shape at 1 < y/d < 3. A peak frequency which characterized the effect of a rotating cylinder had the same value of the rotation rate of a cylinder. In case of cylinder rotation, the depths of mean velocity -defect and turbulent-shear regions were thickened by 20-40% at 0 < x/d < 10 compared with the case of cylinder stationary. Far downstream beyond x/d > 10, the flowfield generated by a rotating cylinder showed self-similarity in the profiles of mean velocity and turbulence quantities. The effect of a rotating cylinder was independent of its rotation rate and Reynolds number in the measurement range.

• Proceedings of the KSME Conference
• /
• 2002.08a
• /
• pp.759-762
• /
• 2002

Automobile aeroacoustics Is a developing area of technology where experimental and theoretical tools are being continuously refined to understand, analyze and modify the noise-generating mechanisms in the vehicle flow. Main sources of ground vehicle exterior noise are the tires (tire/road interaction) and the unsteady flow field around the vehicle. In this study, the sound source localization of a rolling tire was applied to the measurement of radiated sound by using an acoustic mirror system. A possible flow pattern that develops is suggested based on detailed wind tunnel investigations with a rotating wheel in contact with a moving belt.

• 유체기계공업학회:학술대회논문집
• /
• 2004.12a
• /
• pp.629-634
• /
• 2004

Cavities are inevitable structures in automobile configuration. The flow-induced noise is generated from the wheel housing section by the interaction between a rotating wheel and the unsteady flows in the cavity. In this research the wheel housing was assumed by a rectangular cavity for simplification. We measured the radiated sound from the 2-D cavity without cylinder and from the rotating cylinder in the cavity by using the sound source localization method with an acoustic mirror system. In the 2-D cavity case of low Mach number(Ma=0.029), the sound sources were found to be located near the leading edge of cavity due to the shear layer instabilities. Comparing the cases of the rotating and the non-rotating cylinder, it is observed that the sound Pressure levels around the rotating cylinder in the cavity increased and the main acoustic sources were located at the rear section of the rotating wheel.