• 대한조선학회논문집
• /
• 제45권6호
• /
• pp.631-636
• /
• 2008

In this paper, numerical analysis based on the RANS equation and the Realizable ${\kappa}-{\varepsilon}$ turbulence model is carried out for flows around an axisymmetric body at three Reynolds numbers($1.22{\times}10^7$, $1.0{\times}10^8$, $1.5{\times}10^8$) and the numerical results are compared with experiments data. Computed velocity distributions agree well with experiments as the Reynolds number increases. Pressure distributions agree well with the results of the potential flow except the tail region but differ from experiments for the parallel middle body as well as tail region. Pressure gradients show a good agreement with those of potential flow and experiment except the tail region. Friction coefficients show that the numerical results generally are lower than the experimental results estimated from the measured velocity. The difference of friction coefficients between the calculation and the experiment increases with growing of a boundary layer.

• 대한조선학회논문집
• /
• 제36권3호
• /
• pp.15-21
• /
• 1999

KRISO 300K VLCC 이중모형선 주위의 유동특성을 풍동실험을 통해 연구하였다. 선체 선미 주위유동과 후류유동의 평균속도 성분, 난류강도, 레이놀즈 전단응력 및 난류 운동에너지 분포를 열선풍속계를 이용하여 측정하였다. 실험은 선미와 후류의 횡단면에서 수행하였으며, 선체 표면에서의 유동 패턴을 정성적으로 조사하기 위하여 유막법을 이용한 유동가시화도 수행하였다. 선미와 근접 후류영역은 매우 복잡한 3차원의 유동특성을 가지고 있으며, 특히 종방향 와류영역에서 고리 모양의 후류 구조를 볼 수 있었다. 그리고 중앙평행부에서의 얇은 경계층은 선미 영역을 지나며 점차 두꺼워지고 복잡한 3차원 난류후류로 발전하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제24권4호
• /
• pp.486-493
• /
• 2000

Flow mechanism around air flow sensor of electronic control engine, especially Karman vortex type, was investigated experimentally. The two-dimensional flow characteristics in the intermediate wake region behind a triangular vortex-generator respectively apex forward facing, apex backward facing and vertical flat plates following after apex forward facing(i.e vortex-flowmeter) were investigated at Reynolods number of $ReH=1.4\times10^4$; H is the width of a triangular vortex-generator. The vortex shedding frequency for wide Reynolds number from $7\times10^3$ to $2.1\times10^4$ was also surveyed. The velocity component was measured by X-type hot wire anemometer at 8H downstream from the bluff body. The coherent structure of the intermediate wake behind a bluff body was obtained by conditional phase average technique. As a result, it was verified that the vertical flat plates following after apex forward triangular vortex-generator make not only more linear relation between free stream velocity and vortex shedding frequency but also more periodic vortex in the vicinity of the center of wake.

• 한국자동차공학회논문집
• /
• 제9권3호
• /
• pp.201-209
• /
• 2001

Some passenger cars with sunroofs open at tilted positions experience reverse flows into cabin rooms and wind noises much louder compared to other cars. In this study, flows around open sunroofs are numerically studied with the variations of body leakage. The effects of body leakage on ventilation and wind noise of a sun roof are examined, in particular. Furthermore, flow visualization, pressure, and noise measured from wind tunnel and road tests are presented. The results show that too small body leakage results in poor performance of ventilation and generates high wind noise around a sunroof. It is therefore very important to secure an adequate body leakage from the early design stage to achieve better performance of a sunroof as well as passengers' comfort related to HVAC(Heating, Ventilation, and Airconditioning).

• 한국화재소방학회논문지
• /
• 제27권6호
• /
• pp.64-69
• /
• 2013

본 연구에서는 엔진 나셀 화재를 모사하고 이전의 실험결과를 보충하기위해 이차원 둔각물체 주위의 반응유동장에 대하여 수치해석을 수행하였다. Direct numerical simulation (DNS) 기반의 fire dynamic simulator (FDS)를 이용하여 반응유동장의 특성을 조사하였고, 실험결과와의 비교를 통해 화학반응식을 결정하였다. 산화제는 공기를 사용하였고, 연료는 메탄을 사용하였다. 동축류와 대향류 분사 모두의 경우에 화염의 안정성이나 모양은 둔각물체 주위의 와 강도와 크기에 크게 영향을 받았다. 동축류 분사의 경우 계산에 통한 화염소화한계를 결정하였는데 연료유속이 커질수록 공기의 유속 또한 커지는 경향이 있었고, 그 속도들 또한 기존의 실험결과와 잘 일치함을 볼 수 있었다. 유동장 특성에 대한 화학반응의 효과를 고찰하기 위해 반응이 없는 경우를 계산하여 비교하였다. 모든 경우에 비반응 유동장에 비해 반응 유동장의 후류와는 크기도 감소하고 세기도 감소함을 볼 수 있었는데 이는 반응에 의한 후류의 온도증가가 유체의 밀도 및 모멘텀을 감소시켰기 때문으로 판단된다.

• 대한기계학회논문집B
• /
• 제32권10호
• /
• pp.791-799
• /
• 2008

We investigate the flow characteristics around a series of rectangular bodies ($40^d{\times}80^w{\times}80^h$, $80^d{\times}80^w{\times}80^h$ and $160^d{\times}80^w{\times}80^h$) placed in a deep turbulent boundary layer. The study is aiming to understand the surface pressure distribution around the bodies such as the suction pressure in the leading edge, when the flow is normal, which is responsible for producing extreme suction pressures on the roof. The experiment includes wind tunnel work by using HWA (Hot-Wire anemometry) and pressure transducers. The experiments are carried out at three different Reynolds numbers, based on the velocity U at the body height h, of $2.4{\times}10^4$, $4.6{\times}10^4$ and $6.7{\times}10^4$, and large enough that the mean flow is effectively Reynolds number independent. The results include the measurements of the growth of the turbulent boundary layer in the wind tunnel and the surface pressure around the bodies.

• Journal of Ship and Ocean Technology
• /
• 제10권4호
• /
• pp.12-23
• /
• 2006

In this paper, a numerical study is carried out to investigate the turbulent flow around a twin-skeg container ship model with rudders including propeller effects. A commercial CFD code, FLUENT is used with body forces distributed on the propeller disk to simulate the ship stem and wake flows with the propeller in operation. A multi-block, matching, structured grid system has been generated for the container ship hull with twin-skegs in consideration of rudders and body-force propeller disks. The RANS equations for incompressible fluid flows are solved numerically by using a finite volume method. For the turbulence closure, a Reynolds stress model is used in conjunction with a wall function. Computations are carried out for the bare hull as well as the hull with appendages of a twin-skeg container ship model. For the bare hull, the computational results are compared with experimental data and show generally a good agreement. For the hull with appendages, the changes of the stem flow by the rudders and the propellers have been analyzed based on the computed result since there is no experimental data available for comparison. It is found the flow incoming to the rudders has an angle of attack due to the influence of the skegs and thereby the hull surface pressure and the limiting streamlines are changed slightly by the rudders. The axial velocity of the propeller disk is found to be accelerated overall by about 35% due to the propeller operation with the rudders. The area and the magnitude of low pressure on the hull surface enlarge with the flow acceleration caused by the propeller. The propellers are found to have an effect on up to the position where the skeg begins. The propeller slipstream is disturbed strongly by the rudders and the flow is accelerated further and the transverse velocity vectors are weakened due to the flow rectifying effect of the rudder.

• Wind and Structures
• /
• 제2권3호
• /
• pp.173-187
• /
• 1999

The flow around a structure has been an important subject in wind engineering research. There are various kinds of unstable aerodynamic phenomena with regard to a bluff body. In order to understand the physical mechanism of aerodynamic and aeroelastic instability of a bluff body, the relations between the flow around structures and the motion of body with various section shapes should be investigated. Based on a series of wind tunnel tests, this paper addresses the aerodynamic stability of square cylinder with various corner cuts and attack angles in the uniform flow. The test results show that the models with corner cut produced generally better behaviour for the galloping phenomenon than the original section. However, the corner cut method can not prevent the occurrence of the vortex-induced vibration(VIV). It is also shown that as the attack angle changes, the optimum size of corner cut changes also. This means that any one specific size of corner cut which shows the best aerodynamic behaviour throughout all the cases of attack angles does not exist. This paper presents an intensive study on obtaining the optimum size of corner cut for the stabilization of aerodynamic behaviour of cylinders.

• 대한수학회논문집
• /
• 제10권3호
• /
• pp.767-781
• /
• 1995

In this paper we present computation of a reflected shock in the hypersonic flow of air with chemical reactions. We consider two dimensional steady inviscid hypersonic flow of air around bodies including chemical reaction effects. At a high Mach number, a strong shock is formed in front of the body when a wedge is placed against the flow. In front of the shock, temperature and pressure increase greatly and the flow is in nonequilibrium state. If the shock hits a wall, then a reflected shock is formed in the nonequilibrium flow region. Behind this reflected shock, the temperature and pressure are very high. We carry out the computation of the reflected shock and the flow behind it. The jump conditions at the reflected shock are presented. A technique combining smooth transforms of domain and implicit difference methods is used to overcome numerical difficulties associated with the lack of resolution behind the shock and near the body.

• 한국해양공학회지
• /
• 제32권1호
• /
• pp.36-42
• /
• 2018

Unlike a slender body, vortices are shed off alternately in the wake of a blunt body. In the case of liquid flows, when the pressure falls below the vapor pressure, cavitation occurs in the vortex core and affects the formation of the vortex street. This phenomenon is of major importance in many practical cases because the alternate shedding of vortices creates imbalanced forces on the body. Hence, it is very important to determine the shedding frequency of cavitating vortices. In this paper, the unsteady cavitating flow around a two-dimensional wedge-shaped submerged body was simulated using the commercial code STAR-CCM+. A numerical investigation of the structure of cavitating vortices was performed for a model with an apex angle of $20^{\circ}C$. The results were validated by comparing them with experimental measurements carried out at a cavitation tunnel of Chungnam National University (CNU-CT). It was found that the shedding frequency of the vortex increased by up to 18%, which was strongly affected by the development of cavitation.