• 펄프종이기술
• /
• 제33권4호
• /
• pp.21-27
• /
• 2001

Korean traditional paper (Hanji) making technology has adopted two kinds of sheet forming processes, which called "Oebal-choji": and "Ssangbal-choji". The sheet forming process of Oebal-choji is an original method developed in Korea. At first, paper stock is dipped onto the mold and flow away in the forward direction. Then, paper stock is scooped again and rhythmically rocked from side to side, this work is repeated several times. Through this operation the fibers intertwine and paper layers are formed. Ssangbal-choji is almost same as the Nagashizuki, which used in Japan. In this method, paper stock is scooped onto the mold and rhythmically rocked backwards and forwards several times, the water drains slowly through the bamboo screen and then sheet is formed. Tamezuki method is used in Japan and China. This is a method in which the mold is dipped into the paper stock once and left to drain. In the Ssangbal-choji and Nagashizuki methods, the most of excess solution is cast out while in the Tamezuki all of it is allowed to drain through the mold. This study was carried out to investigate the physical properties of the Hanjis that were made by Oebal-choji, Ssangbal-choji, Nagashizuki, and Tamezuki sheet forming processes. The results were follows; Physical properties of the Oebal-choji Hanji were better than those of Ssangbal-choji, Nagashizuki, and Tamezuki. Oebal-choji Hanji made little difference of paper strength between MD and CD, but Ssangbal-chjo and Nagashizuki Hanjis made wide difference. And there are no difference of paper strength between MD and CD on the Tamezuki Hanji. On the confocal laser scanning microscopy (CLSM) observation of the Hanjis, Oebal-choji made well crossed fiber orientation than those of other forming processes.r forming processes.

• Membrane and Water Treatment
• /
• 제3권3호
• /
• pp.151-168
• /
• 2012

Gas sparging is one of the techniques used to control the concentration polarization during ultrafiltration. In this work, the effects of gas sparging in stratified flow regime were investigated during gel layer controlling cross flow ultrafiltration in a rectangular channel. Synthetic solution of pectin was used as the gel forming solute. The liquid and gas flow rates were selected such that a stratified flow regime was prevalent in the channel. A mass transfer model was developed for this system to quantify the effects of gas flow rates on mass transfer coefficient (Sherwood number). The results were compared with the case of no gas sparging. Gas sparging led to an increase of mass transfer coefficient by about 23% in this case. The limitation of the developed model was also evaluated and it was observed that beyond a gas flow rate of 20 l/h, the model was unable to explain the experimental observation, i.e., the decrease in permeate flux with flow rate.

• 대한기계학회논문집B
• /
• 제20권5호
• /
• pp.1700-1716
• /
• 1996

The two-dimensional, unsteady, laminar conservation equations for mass, momentum, energy and species transport in the gas phase and mass, momentum and energy in the liquid phase are solved simultaneously in spherical coordinates in order to study heating and vaporization of a droplet entrained in the oscillating flow. The numerical solution gives the velocity and temperature distribution in both gas and liquid phase as a function of time. When the gas flow oscillates around an vaporizing droplet, the liquid flow circulates in the clockwise or counterclockwise direction and the temperature distribution in the liquid phase changes its shapes, depending on the gas fow direction. When the gas flow changes its direction of circulating liquid flow is opposite to the gas flow, forming two vortex circulating in the opposite direction. During the heating period, the difference in the maximum and minimum temperature is large, followed by the almost uniform temperature slightly below the boiling temperature. The mass and heat transfer from the droplet depend on the droplet temperature, droplet diameter and the magnitude of relative velocity, giving the droplet lifetime different from the d$^{2}$-law.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2008년도 춘계학술대회 논문집
• /
• pp.187-188
• /
• 2008

• KSBB Journal
• /
• 제13권5호
• /
• pp.477-482
• /
• 1998

A biosensor with PZT piezoelectric ceramic crystal was developed for the detection of formaldehyde gas. Poled PZT piezoelectric ceramic disk was made from ZrO2, TiO2 and Nb2O5, together with the addition of PbO and polyvinyl alcohol, through various processes of mixing, calcination drying, crushing, forming, sintering, polishing, ion coating and poling. Oscillator circuit of sensor was made of operational amplifier(AD811AN). Formaldehyde dehydrogenase was immobilized onto a piezoelectic ceramic crystal, together with the cofactors, reduced glutathione and nicotinamide adenine dinucleotide. The effect of flow rate on the sensitivity was determined by varing the flow rate of carrier gas from 24.7mL/min to 111.7mL/min through detector cell. The results indicated that as the flow rate was increased, the recovery rate was increased. And a significant increase in the sensitivity was observed in enhanced flow rate of carrier gas. Frequency difference(ΔF) of immobilized PZT piezoelectic disk increased proportionally to the concentration gas and reproduced to repeated exposures of formaldehyde gas(28ppm, Δ68Hz).

• Design & Manufacturing
• /
• 제6권2호
• /
• pp.42-47
• /
• 2012

The paper deals with an analysis of an extrusion process with a divided material flow in a combined radial - backward extrusion. We have discussed the influences of tool geometry such as punch nose angle, relative gap height, die corner radius on material flow and surface expansion into can and flange region. To analyse the process, numerical simulations by the FEM and experiment by physical modeling using Al alloy as a model material have been performed. Based on the results, the influence of fixed parameters on the distribution of divided material flow and surface expansion are obtained.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2006년 제4회 한국유체공학학술대회 논문집
• /
• pp.345-348
• /
• 2006

In sheet metal forming process using press and draw die some defect can be made because of the high pressure of air pocket between draw die and the product. The purpose of this study is to develop a program to decide an optimal combination of air vent hole size and number to prevent those defect on product. The air inside air pocket is considered as ideal gas and the compression and expansion is assumed as isentropic process. The mass flow is computed in two flow condition: unchocked and chocked condition. The present computation obtains required cross-sectional area of air vent hole for not exceeding the user specified pressure such as the pressure for yielding strength of the product or the pressure for unchocked flow. To validate the program the present results are compared with the results of other researchers and commercial CFD code.

• 한국환경과학회지
• /
• 제26권1호
• /
• pp.11-21
• /
• 2017

In this study, bacterial growth was assessed by flow cytometry analysis of fluorescent probes-stained bacteria. Flow cytometry has many advantages of rapid analytical time, a low standard deviation, and highly sensitive detection of live and Dead E.coli over colony forming assay. When untreated bacteria were stained by using Thiazole Orange (TO) and Propidium Iodide (PI), double staining had a short analytical time as compared with that of single staining while its error rate was similar to that of single staining. Through double staining experiments, it was determined that optimal concentrations for TO and PI staining were 420 nM and $9.6{\mu}M$, respectively.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 추계학술대회 논문집
• /
• pp.332-337
• /
• 2009

Recently, boss and rib test based on backward extrusion process was proposed to quantitative evaluate the interfacial friction condition in bulk forming process. In this test, the tube-shaped punch with hole pressurizes the workpiece so that the boss and rib are formed along the hole and outer surface of the punch. It was experimentally and numerically revealed that the height of boss is higher than that of the rib under the severe friction condition. This work is focused on the effect of the punch design and friction condition on deformation pattern in boss and rib test. From the boss and rib test simulations, it was found that there is slight variation in both the heights of boss and rib according to the length of punch land, nose radius, and face angle. However the hole diameter of the punch and the clearance between the punch and die have a significant influence on the heights of the boss and rib. In addition, the effect of flow stress was also investigated on the deformation patterns through FE simulations.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 2010년도 춘계학술발표회 논문집
• /
• pp.227-227
• /
• 2010

기존 도공지 생산 공정에서 널리 사용되던 블레이드 도공방식을 대체할 수 있을 것으로 기대되는 커튼코팅 방식은 스크래치, 스트릭, 미스팅, 블레이드의 마모등을 발생시키지 않고 고고형분 도공이 가능하며 우수한 커버리지를 갖는 도공층을 형성시킬 수 있다는 장점을 갖고 있다. 뿐만 아니라 하나의 코팅 유닛에서 여러개의 도공층을 한번에 형성시킬 수 있어 설비투자비용 및 건조에너지, 공간활용도 절감 측면에서도 한층 유리하다. 커튼 코팅 방식에서 도공액의 유동은 도공액이 필름 형태로 사출되는 sheet forming zone, 도공액 커튼이 낙하하는 curtain flow zone, 도공액 커튼이 원지와 접촉하는 impingement zone으로 나뉜다. 커튼 코팅이 이루어지기 위해서는 sheet forming zone과 curtain flow zone에서 도공액이 얇은 막 상태를 안정적으로 유지하고 impingement zone에서는 고속으로 이송되는 도공원지에 의한 급격한 신장 조건에서 도공액 필름이 끊어지지 않고 유지되어야 한다. 이를 위해 유화제를 통해 동적 표면 장력을 낮초고 rheology modifier를 통해 점도 및 신장점도를 조절해 도공액의 커튼 안정성을 부여하는 연구가 보고된 바 있다. 도공액 제조시 바인더로 널리 사용되는 S/B 라텍스는 입도, 유리전이온도, 표면전하 등 그 특성을 달리하여 제조할 수 있으며 이러한 특성에 따라 도공액의 점도와 같은 유변특성이 변화하여 도공액의 커튼 안정성에 영향할 것으로 예상된다. 따라서 본 연구에서는 입자경과 유리전이온도, 카르복실화 정도 등을 달리한 다양한 S/B 라텍스를 사용하여 유변특성을 달리한 도공액을 제조하고 커튼 안정성의 변화를 살펴보고자 하였다.