• Journal of Sensor Science and Technology
• /
• v.29 no.2
• /
• pp.75-81
• /
• 2020

We introduce a new visible light communication (VLC) method in which three-level return-to-zero (RZ) modulation is used for flicker-free transmission. In the VLC transmitter, the three-level RZ modulation ensures that the average optical power is constant; thus, a flicker-free light-emitting diode (LED) light is achieved. In the VLC receiver, a resistor-capacitor high-pass filter is used for generating spike signals, which are used for data recovery while eliminating the 120 Hz optical noise from adjacent lighting lamps. In transmission experiments, we applied this method for wireless transmission of an air quality sensor message using the visible light of an LED array. This configuration is useful for the construction of indoor wireless sensor networks for air pollution monitoring using LED lights.

• Journal of Sensor Science and Technology
• /
• v.29 no.3
• /
• pp.180-186
• /
• 2020

In this study, we applied edge-pulse modulation to prevent the flicker of light-emitting diode (LED) light in a visible light identification system. In the visible light transmitter, positive pulses were transmitted at the edges of the low-to-high transition points, and negative pulses were transmitted at the edges of the high-to-low transition points of the non-return-to-zero (NRZ) data waveforms. In the visible light receiver, the NRZ waveforms were regenerated by making low-to-high and high-to-low transitions at the point of the positive and negative pulses, respectively. This method has two advantages. First, it ensures that the LED light is flicker-free because the average optical power of the LED was kept constant during data transmission in the transmitter. Second, the 120 Hz optical noise from the adjacent lighting lamps was easily cut off using a simple RC-high pass filter in the receiver.

• Journal of Satellite, Information and Communications
• /
• v.7 no.3
• /
• pp.41-46
• /
• 2012

Visible light communication(VLC) system based on LED devices has some specific advantages compared with RF system. First, visible light is harmless to human and there is no limit to using frequency band. Also, VLC system has good security performance, and it can use the very wide frequency band for data transmission. However, for simultaneously using the illumination and data transmission in VLC systems, degradation of code rate is occurred. So, in this paper, we proposed the novel line coding scheme for flicker free and efficient dimming control in VLC systems. From the simulation results, it is confirmed that proposed scheme has good flicker, dimming, and transmission performance compared to conventional variable pulse position modulation(VPPM) scheme.

• Journal of Sensor Science and Technology
• /
• v.28 no.3
• /
• pp.191-197
• /
• 2019

In this study, we propose a dimming control method for a visible light communication (VLC) system, in which the subcarrier on-off keying (OOK) modulation of Manchester code is used for data transmission. In the VLC transmitter, non-return-to-zero (NRZ) code data is transformed to Manchester code, which is OOK modulated with a subcarrier. Manchester code is used for flicker-free lighting; the duty factor is changed for dimming control, and the subcarrier is used for preventing the adjacent noise light interference. In the experiments, the dimming control was carried out from about 8%-92% of the continuous wave (CW) LED light. This configuration is simple and effective in constructing a VLC system for indoor wireless sensor networks with flicker-free illumination and dimming control capability without adjacent noise light interference.

• Journal of Sensor Science and Technology
• /
• v.29 no.4
• /
• pp.243-248
• /
• 2020

In this study, we applied transition-frequency modulation to prevent the flickering of light-emitting diodes (LEDs) in visible light communication (VLC). In the VLC transmitter, rectangular waveforms with transition frequencies of four and two in each bit time were used for the high and low bits, respectively, in the non-return-to-zero data. In the VLC receiver, an RC-high-pass filter (HPF) was used to eliminate the interference of the 120 Hz noise light from the adjacent lighting lamps, and an SR-latch circuit was used to recover the transmitted signal using spikes from the output of the RC-HPF. This configuration is useful for constructing VLC systems that are flicker-free and resistant to adjacent noise light interference.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.41 no.8
• /
• pp.843-850
• /
• 2016

This paper introduces a novel modulation scheme for vehicular communication in taking advantage of existing LED lights available on a car. Our proposed 2-Phase Shift Keying (2-PSK) is a spatial modulation approach in which a pair of LED light sources in a car (either rear LEDs or front LEDs) is used as a transmitter. A typical camera (i.e. low frame rate at no greater than 30fps) that either a global shutter camera or a rolling shutter camera can be used as a receiver. The modulation scheme is a part of our Image Sensor Communication proposal submitted to IEEE 802.15.7r1 (TG7r1) recently. Also, a neural network approach is applied to improve the performance of LEDs detection and decoding under the noisy situation. Later, some analysis and experiment results are presented to indicate the performance of our system

• Journal of Sensor Science and Technology
• /
• v.30 no.4
• /
• pp.196-203
• /
• 2021

In this study, an optical identification system was developed, wherein visible light is used to transmit the interrogating signal, and infrared is used to send the response signal. In the reader, visible light from a light emitting diode (LED) array was modulated via modified pulse width modulation for flicker-free illumination and dimming control. Moreover, the duty factor of the dimming control time was employed to control the illumination from the LED. In the transponder, the spike signal in the output of the high-pass filter was utilized to recover the interrogating signal while preventing interference from the 120-Hz noise from adjacent lighting lamps. The illumination was controlled in 26-86% range of the constant wave LED illumination by changing the duty factor from 20% to 90%. This configuration is advantageous for the construction of optical identification systems for automatic security check and car fare calculation at toll gates or parking facilities.

• Journal of information and communication convergence engineering
• /
• v.19 no.4
• /
• pp.269-275
• /
• 2021

Light-emitting diodes (LEDs) are modulated using a square wave pulse sequence for flicker prevention and dimming control in visible light communication (VLC). In a VLC transmitter, the high and low bits of the non-return-to-zero (NRZ) data are converted to two square waves of different frequencies, which continue for a finite time defined by the fill ratio in an NRZ bit time. As the average optical power was kept constant and independent of data transmission, the LED was flicker-free. Dimming control is carried out by changing the fill ratio of the square wave in the NRZ bit time. In the experiments, the illumination of the LED light was controlled in the range of approximately 19.2% to 96.2% of the continuous square wave modulated LED light. In the VLC receiver, a high-pass filter combined with a latch circuit was used to recover the transmitted signal while preventing noise interference from adjacent lighting lamps.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.37 no.6
• /
• pp.9-16
• /
• 2000

The perception of flicker on the computer display devices depends upon the temporal waveform of the phosphor decay characteristic, the frame rate, and the display size. The lowest frequency at which flicker is not perceived is called the critical fusion frequency or critical frequency. Critical fusion frequency is evaluated by the display illuminance and the modulation (m) defined as the ratio of the amplitude of first harmonic frequency to the DC of the waveform. In this paper, we analyze the relationship bet ween the critical fusion frequency, relating to the decay characteristic of the phosphors and luminance on the monitor, and the frame frequency. Also under considering the viewing angle, we presented the frame frequency that is less sensitive to the full size of the display device.

• Journal of Institute of Control, Robotics and Systems
• /
• v.21 no.1
• /
• pp.76-79
• /
• 2015

Visible light communication (VLC) is a short range optical communication technology using light emitting diodes. In this paper, we implement variable pulse position modulation (VPPM) defined in the IEEE 802.15.7 standard with a Cortex-M processor, which is a new modulation scheme for VLC providing a dimming control mechanism for flicker-free optical communication. The synchronization procedure between the transmitter and receiver is not defined clearly in the VPPM standard. In order to synchronize the transmitter and receiver easily, two overhead bits are used including one start bit and one stop bit modulated by on-off keying (OOK). Experimental results under various environmental conditions show that the proposed VPPM can support a seamless 100 Kbps data rate with 10 levels in the dimming control.