• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 하계학술대회 논문집 C
• /
• pp.1434-1436
• /
• 2002

The 400KN suspended insulator was fabricated with feldspar, quartz, clay and $Al_2O_3$ wt% for extra high voltage. These materials were grinded with ball milling for 25 hours after mixing them. The grinded materials were sintered at $1300^{\circ}C$ for 50 minutes in the tunnel kiln after mading with jiggering method. The sintered density of specimen was reached at 97% in comparison with that of theory. The specimen had the characteristic of temperature rise with the increase of electrical losses. Also, the flexural strength and the fracture toughness of sintered parts respectively were 1658 kg/$cm^2$ and 2.3 $MPa{\cdot}m^{1/2}$.

• The Korean Journal of Ceramics
• /
• 제6권3호
• /
• pp.193-200
• /
• 2000

Si$_3$N$_4$powder with 2 wt% $Al_2$O$_3$and 6 wt% $Y_2$O$_3$additives was sintered by the gas pressure sintering (GPS) technique. The unlubricated wear behavior depending on sintering conditions such as sintering temperature, pressure, and sintering time was investigated. When the sintering temperature and time increased, the larger elongated grains were formed and the microstructural heterogeneity increased. When sintering pressure increased, grain growth, however, was impeded. Also, the wear properties depended on microstructure and friction coefficient were related to grain size. Based on the experimental results, the wear properties were associated with initial friction coefficients as well as mechanical properties including fracture toughness and flexural strength.

• 한국세라믹학회지
• /
• 제31권9호
• /
• pp.1021-1029
• /
• 1994

SiC ultrafine particles of 1, 10, 20 and 30 vol% were dispersed in $\alpha$-Si3N4 matrix and hot-pressed under the condition of 30 MPa at 1800 and 190$0^{\circ}C$ respectively. Physical, mechanical properties and microstructures of sintered Si3N4-SiC nanocomposites were investigated. Flexural strength and density of Si3N4-10 vol% SiC nanocomposites hot-pressed at 190$0^{\circ}C$ represented the 1002 MPa and 97.9%T.D respectively, and it was confirmed as a remarkable improvement of 67% compared to Si3N4 monolith. Fracture toughness was shown as 7.2 MPa.m1/2 when the same composition was hot pressed at 180$0^{\circ}C$. This effect was supposed to be due to the improvement of microstructure by the adequate suppression of the excessive growth of Si3N4 grain with SiC nano-particles.

• 한국세라믹학회지
• /
• 제32권11호
• /
• pp.1255-1261
• /
• 1995

Mullite-spinel-zirconia composites were prepared by reaction sintering of calcined alumina and magnesia, and zircon powders. The influence of calcining temperature on densification processes and on mechaical properties of subsequently sintered compacts was investigated. The mullite was formed by the reaction of $\alpha$-Al2O3 and amorphous SiO2 at firing temperatures over 141$0^{\circ}C$. The mullitization proceeded more rapidly in the specimen calcined at 110$0^{\circ}C$ than at either 120$0^{\circ}C$ or 130$0^{\circ}C$. Microstructures before and after the mullitization (or mullite dissociation) showed different morphologies, and their effects on mechanical properties were significant. The flexural strength and fracture toughness of the specimen calcined at 130$0^{\circ}C$ and subsequently fired at 145$0^{\circ}C$ were 316 MPa and 4.2Mpa.m1/2, respectively.

• 한국세라믹학회지
• /
• 제34권10호
• /
• pp.1053-1059
• /
• 1997

The dynamic fatigue behavior of alumina ceramics was observed at room temperature using four point bending system. The dynamic fatigue fracture strength and the dynamic fatigue lifetime were observed as a function of crosshead speed and the notch length. The notched specimen showed the smaller deviation in dynamic fatigue fracture strength than the unnotched specimen. The crack growth exponent n and the material constant A of the notched specimen could be represented as functions of the notch length. Fracture strength of the specimen calculated from the notch length, when the notch length was regarded as the crack size, was in good agreement with the measured 4 point bending strength. Fracture surface of the specimen showed the different fracture modes according to the crosshead speed. The four point flexural strength, fracture toughness, Young's modulus and Weibull modulus of the alumina were measured as 360 MPa, 3.91 MPa.m1/2, 159GPa, 17.64, respectively.

• 한국세라믹학회지
• /
• 제31권3호
• /
• pp.330-336
• /
• 1994

High strength cement composites (W/C=0.1) were prepared by using various blending materials such as SiC whisker and white carbon (hydrated silica: SiO2·nH2O). The effect of various blending materials on the microstructure and strength of the hardened cement paste were investigated in the view of fracture mechanics. The plain specimen showed 101 MPa of flexural strength, 81 GPa of Young's modulus and 1.32 MPam1/2 of fracture toughness. When the blending materials were added to the composites, their values were enhanced to about 110∼138 MPa, 95∼146 GPa and 1.32∼1.87MPam1/2 respectively. The improvement of the mechanical strength for the hardened cement paste may be due to the removal of macropores, the reduction of total porosity, pozzolanic reaction and the increase of various fracture toughening effect.

• 한국신뢰성학회지:신뢰성응용연구
• /
• 제15권3호
• /
• pp.216-221
• /
• 2015

Sintering behavior of 3%yttria-stabilized zirconia was comparatively studied using a spray-dried powder produced by a domestic and global company. Quality of the sintered block was analysed in terms of relative density, shrinkage rate, grain growth, hardness, and fracture toughness. Relative density, shrinkage rate, and hardness value of the finally sintered block was similar between domestic and global zirconia powder, respectively. But, flexural strength of the domestic powder specimen was about 70% of the sintered block produced by using a global powder. The poor sintering quality of the domestic powder was discussed in relation with compressibility of the spray-dried granule-type powder and the amount of monoclinic phase in the as-received powder.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1992년도 봄 학술발표회 논문집
• /
• pp.35-40
• /
• 1992

Results of an experimental study on the manufacture, the workability and mechanical properties of steel fiber reinforced polyester resin composites utilizing industrial waste products are presented in this paper. The fly ash polyester resin composites using steel fiber, fly ash and calcium carbonic acid (CaCo3), unsaturated polyester resin, styrene monomer, cobalt octate and methyl ethyl ketone peroxide, fine and coarse aggregates are prepared with various filler~binder rations, binder rates and mixing conditions. As a test results, the workability of steel fiber reinforced polyester resin composites are considerably dropped with increasing fly ash-binder ratio and steel fiber volume. And compressive, flexural strength and bending toughness of the composites are remarkably improved with augmenting fiber contents.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1997년도 봄 학술발표회 논문집
• /
• pp.308-314
• /
• 1997

Shrinkage and creep are the fundamental properties of concrete. These long term deformations can be seen as bothersome(increased deflection) or can be seen as reduction of compressive stress of prestressed concrete. Steel fibers advance the mechanical properties of concrete:tensile strength, ductility, flexural strength, fracture toughness, and post-cracking resistance, etc...Silica fume is pozzolanic material which combines with hydrated lime to generate silicate materials which increase the compressive strength and reduce somewhat the creep of concrete. This paper is the result of the long-term deformation by silica fume and steel fibers with varying percentages.

• 한국세라믹학회지
• /
• 제29권10호
• /
• pp.797-805
• /
• 1992

Al2O3-20 wt% ZrO2 composite powders to be used as the starting materials of the Al2O3/ZrO2-Spinel composite system were prepared by the use of the emulsion-hot kerosene drying method. The crystalline phase of ZrO2 in the synthesized Al2O3-ZrO2 composite powders was 100% tetragonal but the small amount of t-ZrO2 was transformed into m-ZrO2 after crushing. The hardness, fracture toughness, and flexural strength of the composite, which was sintered at 1650$^{\circ}C$ for 4 hrs after calcining at 1100$^{\circ}C$ for 2 hrs and had the relative density of 99%, were 15.7 GPa, 4.97 MN/m3/2, and 390 MPa, respectively. The fracture form in the sintered composites was found to be the intergranular fracture.