• Computers and Concrete
• /
• 제3권4호
• /
• pp.261-284
• /
• 2006

The flexural behaviour of symmetrically reinforced concrete (RC) columns cast of normal- and high-strength concrete under both monotonic and cyclic loading is studied based on an analytical procedure, which employs the actual stress-strain curves and takes into account the stress-path dependence of concrete and steel reinforcement. The analysis is particularly extended into the post-peak stage with large inelastic deformation at various applied axial load level. The effect of axial load on their complete flexural behaviour is then identified based on the results obtained. The axial load is found to have fairly large effect on the flexural behaviour of RC columns under both monotonic and cyclic loading. Such effects are discussed through examination of various aspects including the moment-curvature relationship, moment capacity, flexural ductility, variation of neutral axis depth and steel stress.

• 한국강구조학회 논문집
• /
• 제23권6호
• /
• pp.647-657
• /
• 2011

본 논문에는 국부좌굴이 발생하는 휨부재의 유한요소해석 및 실험에 근거한 단면의 휨강도에 대하여 기술하였다. 박판으로 구성된 휨부재는 단면조건 및 횡방향 경계조건에 따라서 국부좌굴, 횡-비틀림좌굴 및 두 좌굴의 혼합좌굴이 발생하게 된다. 플랜지나 복부의 폭-두 께비가 큰 경우 횡-비틀림좌굴 발생 이전에 국부좌굴이 발생하며, 국부좌굴은 휨부재의 횡-비틀림좌굴강도에 영향을 미치게 된다. 이런 현상은 박판 형강의 휨강도 산정 시 고려하여야 한다. 다양한 폭-두께비를 갖는 플랜지와 복부판으로 구성된 휨부재의 해석에 국부좌굴 및 횡좌굴 모드의 초기처짐 및 잔류응력을 포함하였다. 해석결과 및 실험에 근거하여 국부좌굴과 횡-비틀림좌굴을 고려하는 설계강도식을 제안하였다. 제안된 직접강도법은 실험에 근거한 강도식과 유효단면 대신 총단면의 단면계수를 사용한다. 제안된 강도식에 의한 휨강도를 AISC, EC3 및 도로교설계기준과 비교하여 보았다. 제안된 직접강도법은 국부좌굴과 횡-비틀림좌굴의 혼합 유무와 상관없이 휨부재의 휨강도를 적절하게 예측할 수 있는 것으로 판단되었다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2005년도 봄학술 발표회 논문집(I)
• /
• pp.415-418
• /
• 2005

Prestressed composite girder bridges with PS tendon at positive flexural moment region offer elastic behavior to higher loads, increased ultimate capacity and reduced structural steel weight. Two beams were tested to examine ultimate behaviors of prestressed composite girder bridges subjected to positive flexural moment. The experimental observations of the Prestressed composite girder bridges subjected to positive flexural moment are investigated and compared to the numerical results obtained by sectional analysis method, and 1-D. and 3-D. finite element analysis methods.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2005년도 봄학술 발표회 논문집(I)
• /
• pp.419-422
• /
• 2005

Prestressed composite girder bridges with concrete infilled steel tube at negative flexural moment region takes the advantages provided due to the interactive reaction in the steel tube and concrete interface layer, enhancing local buckling resistance and the concrete strength provided by the lateral confining effect of concrete. Two beams were tested to examine ultimate behaviors of prestressed composite girder bridges subjected to negative flexural moment. The experimental observations of the Prestressed composite girder bridges subjected to positive flexural moment are investigated and compared to the numerical results obtained by sectional analysis method, and 1-D. and 3-D. finite element analysis methods.

• Computers and Concrete
• /
• 제20권2호
• /
• pp.129-143
• /
• 2017

Seismic design of reinforced concrete (RC) structures requires a certain minimum level of flexural ductility. For example, Eurocode EN1998-1 directly specifies a minimum flexural ductility for RC beams, while Chinese code GB50011 limits the equivalent rectangular stress block depth ratio at peak resisting moment to achieve a certain nominal minimum flexural ductility indirectly. Although confinement is effective in improving the ductility of RC beams, most design codes do not provide any guidelines due to the lack of a suitable theory. In this study, the confinement for desirable flexural ductility performance of both normal- and high-strength concrete beams is evaluated based on a rigorous full-range moment-curvature analysis. An effective strategy is proposed for flexural ductility design of RC beams taking into account confinement. The key parameters considered include the maximum difference of tension and compression reinforcement ratios, and maximum neutral axis depth ratio at peak resisting moment. Empirical formulae and tables are then developed to provide guidelines accordingly.

• 한국공간구조학회논문집
• /
• 제22권1호
• /
• pp.59-66
• /
• 2022

In this paper, the flexural capacity equation of FRP-bar reinforced concrete beams was verified by comparing the experimental results and flexural capacity obtained according to the ACI procedure. And, also the economic feasibility of FRP-bar reinforced concrete beams was analyzed by comparing nominal moment capacity of beams. The results of analysis were as follows, 1) GFRP concrete beams have lower flexural performance than reinforced concrete beams, whereas CFRP concrete beams have similar flexural performance to reinforced concrete beams under the same reinforcement ratio 2) Although the design moment increased as the compressive strength of concrete increased, the flexural performance of GFRP reinforced concrete beams was found to be lower than the reinforced concrete beams for all reinforcement ratios.

• Structural Engineering and Mechanics
• /
• 제43권2호
• /
• pp.225-237
• /
• 2012

This paper presents an experimental investigation of the flexural behavior of square hollow steel section (HSS) beams subjected to pure bending. Totally six unfilled and nine ultra high performance concrete (UHPC)-filled HSS beams were tested under four-point bending until failure. The effects of the steel tube thickness, the yield strength of the steel tube and the strength of concrete on moment capacity, curvature, and ductility of UHPC-filled HSS beams were examined. The performance indices named relative ductility index (RDI) and strength increasing factor (SIF) were investigated with regard to different height-to-thickness ratio of the specimens. The flexural strengths obtained from the tests were compared with the values predicted by Eurocode 4, AISC-LRFD and CIDECT design codes. The results showed that the increase in the moment capacity and the corresponding curvature is much greater for thinner HSS beams than thicker ones. Eurocode 4 and AISC-LRFD predict the ultimate moment capacity of the all UHPC-filled HSS beams conservatively.

• 한국강구조학회 논문집
• /
• 제22권4호
• /
• pp.377-388
• /
• 2010

HSB600 및 HSB800 고성능강재를 적용한 정모멘트부 강합성거더의 휨거동을 비선형 모멘트-곡률 해석법으로 분석하였다. 연성특성이 다른 3개의 대표적인 강합성거더 기본 단면을 선정하여 모멘트-곡률 해석법으로 모멘트-곡률 이력과 휨저항강도를 구하고 비선형 유한요소해석 프로그램 ABAQUS(2008)로 구한 결과와 비교하여 모멘트-곡률 해석 프로그램을 검증하였다. 비선형 유한요소해석 시에는 플랜지, 복부판 및 콘크리트 바닥판을 판요소로 모델링하여 3차원 강합성거더 유한요소모델을 적용했으며 초기변형과 단면의 잔류응력을 고려하여 해석하였다. 강합성거더 단면에서 콘크리트 바닥판의 28일 압축강도는 30~50MPa를 고려하였으며, 콘크리트 재료는 CEB-FIP(1990) 모델로, 일반 강재와 HSB600 및 HSB800 고성능 강재는 탄소성-변형경화 재료로 모델링하였다. 강합성단면의 연성비, 강거더의 강종, 콘크리트 바닥판의 압축강도, 소성중립축의 위치 등이 강합성거더의 연성특성 및 휨저항강도에 미치는 영향을 분석하였다.

• Structural Engineering and Mechanics
• /
• 제12권1호
• /
• pp.1-16
• /
• 2001

A reliable and accurate method has been developed to predict the flexural deformation response of structural concrete members subject to service load. The method that has been developed relates the extent of concrete cracking, measured as a function of the magnitude of applied moment in a member, to the reduction in the effective moment of inertia of cracked reinforced concrete members under service load conditions. The ratio of the area of the moment diagram where the moment exceeds the cracking moment, to the total area of the moment diagram for any loading, provides the basis for the calculation of the effective moment of inertia. This ratio also represents mathematically a probability of crack occurrence. Verification of this method for the determination of the effective moment of inertia has been achieved from an experimental test program, and has included beam tests with different loading configurations, and shear wall tests subjected to a range of vertical and lateral load levels. Further verification of this method has been made with reference to the experimental investigation of other recently published work.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 봄 학술발표회논문집(II)
• /
• pp.421-426
• /
• 1998

Current code provisions for the development of positive moment reinforcement is reviewed and criticized in this paper. Both the flexural bond and development length concepts are neccesary to consider anchorage requirement of reinforcement at beam ends. The curent design codes show unconservatism for the detailing of reinforcement at the beam ends. This study proposes a new design formula for the development of positive moment reinforcement.