• Journal of the Korean Society for Precision Engineering
• /
• v.8 no.3
• /
• pp.44-54
• /
• 1991

A Study was made on falnk wear in carbide tools in turning SUS304 steel. When an austenitic stainless steel (SUS304 steel) is cut with the tool, saw-toothed chip are produced. It is found that machining SUS304 steel would make a tool worn fast. For increasing productivity, tool wear has to be predicted and controlled. An amended cutting geometry consisting of a negative rake angle ($-6^{\circ}$ ) and a high clearance angle ($-17^{\circ}$ ) is proposed for decreasing carbide tool wear (flank) in the machining of SUS304 steel. The amended cutting geometry is found to make the flank wear lower than a general cutting geometry (rake angle $6^{\circ}$ , clearance angle $5^{\circ}$). The effects of the three cutting variables (cutting speed, feed, tool radius) on the flank wear analyzed by fiting a simple first-order model containing interaction terms to each flank wear parameter by means of regression analysis and the predicted from first-order regression analysis model equation of flank wear.

• Journal of the Korean Society for Precision Engineering
• /
• v.11 no.2
• /
• pp.182-188
• /
• 1994

This expermintal study is intended to investigate he development of flank wear in turning os SUS304 which is used in industrial applications and is acknowledged as a machining difficult material. In cutting process, change of velocity, change of feed, and change of depth of cut were investigated about the effect of flank wear, and slenderness ratio is also investigated. The variations of unit cutting force with the change of rake angle and the change of uncut chip area are observed. The friction angles are calculated for the change friction force and observed. The friction angles are calculated for the change friction force and normal forcd on the different rake angles. From this experimental study, the following results can be said. 1. Under the high cutting speed condition, the flaank wear is affected by the feed and depth of cut, but the influence of feed and depth of cut to the flank wear is reduced when the velocity is low. 2. The smaller slenderness ratio is, the shorter the tool life results in high cutting speed, and the lower cutting speed is, the lower the effect of slenderness ratio to the flank wear is. 3. Using the characteristics of force-RMS, the flank wear of a tool can be detected. There are almost no differences between the RMS characteristics of cutting force and feed force.

• Journal of Industrial Technology
• /
• v.20 no.A
• /
• pp.169-178
• /
• 2000

The 4-point bending tests have been performed In order to estimate the effect of TIG-dressing on fatigue strength and fatigue characteristics quantitatively for non load-carrying fillet welded joints subjected to pure bending. As a result of fatigue tests, fatigue strengths of as-welded specimens have satisfied the grade of fatigue strength prescribed in specifications of korea, AASHTO and JSSC. Fatigue strength at 2 million cycles of TIG-dressing specimens have increased compared with as-welded specimens. As the result of beachmark tests, fatigue cracks occurred at several points, where the radius of curvature and flank angle in the weld bead toes were low, and grew as semi-elliptical cracks, then approached to fracture. As a result of finite element analysis, stress concentration factor in weld bead toes has closely related to the flank angle and radius of curvature, and between these, the radius of curvature has more largely affected in stress concentration factor than flank angle. As a result of fracture mechanics approaches, the crack correction factor of test specimens has largely affected on stress gradient correction factor in case a/t is below 0.4. From the relations between stress intensity factor range estimated from FEM analysis and fatigue crack growth rate, fatigue life has been correctly calculated.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.892-897
• /
• 2000

In this study, tap wear was analyzed not only to predict the tap life time but also to propose an improved tap design. Because rake angle and thread relief of tap are the significant factors in geometry of tap, these two factors were picked as the experiment variables. The experiment was conducted with six types of tap which have 6$^{\circ}$ , 8$^{\circ}$ and 12$^{\circ}$ of rake angles with 0,08mm and 0.14 mm of thread relief. From the measured cutting force, it could be known that cutting torque was low at the large the rake thread relief and tool life was long as rake angle became large. Eventually, tool life is longest when rake angle is 12$^{\circ}$ and the with 0.08mm thread relief. Aand the width of crater wear and that of flank wear were measured when a tapping torque was 20 [$kg_f$-mm] . Most of the measured values were above the width of tool wear[$V_B$=O.O3m], which means that tool life is over.

• Journal of computational fluids engineering
• /
• v.18 no.4
• /
• pp.1-8
• /
• 2013

The performance of small-size impellers with ruled surfaces was investigated for flank milling over a wide speed range, using computational fluid dynamics analyses and gas bench tests. An impeller with a ruled surface was designed, manufactured, and tested to evaluate the effects of blade loading, the backsweep angle, and the relative velocity distribution on the compressor performance. The simulations and tests were completed using the same compressor cover with identical inlet and outlet channels to accurately compare the performance of the abovementioned impeller with a commercial impeller containing sculptured blades. Both impellers have the same number of blades, number of splitters, and shroud meridional profiles. The backsweep angles of the blades on the ruled impeller were selected to work with the same pinched diffuser as for a sculptured impeller. The inlet-to-exit relative velocity diffusion ratio and the blade loading were provided to maximize the flow rate and to minimize the surge flow rate. The design flow rate, rpm, were selected same for both impellers. Test results showed that for the compressor stage with a ruled impeller, the efficiency was increased by 0.32% with an extended surge margin without a reduction in the pressure ratio as compared to the impeller with the sculptured design. It was concluded that an increased relative velocity diffusion coupled with a large backsweep angle was an effective way to improve the compressor stage efficiency. Additionally, an appropriate blade loading distribution was important for achieving a wide operating range and higher efficiency.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.13 no.2
• /
• pp.134-143
• /
• 2001

This paper presents the characteristics of flank and tip seal leakage in a scroll compressor for air-conditioners with R-22 under actual operating conditions. It is well known that the leakage has significant effect on the performance of the scroll compressor. Experiments were performed by using indirect method for measuring mass flow rate passing through flank and tip seal under actual operating conditions, In addition, an analytical model for tip seal leakage was developed to investigate tangential and radial leakage observed at grooves and contact points of tip seals. For low oil concentration, theoretical results were compared with experimental data to verify the analytical model. As a result, leakages through flank and tip seal parts were evaluated as afunction of pressure ratio, orbiting angle, discharge pressure, tip clearance, and leakage point. It was also found that the tip seal leakage was considerable even though the tip seal provided adequate sealing effect.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.312-315
• /
• 2002

This paper summarizes the results of a numerical study conducted to analyze the effect of selected process parameters on material flow and thread profile in thread rolling of large diameter blanks. Based on the previous work where a plane strain mode was found to provide a reasonable approximation of the thread rolling process, the effect of varying thread form, friction factor, flow stress, and blank diameter on effective strain and thread height was analyzed using the finite element code DEFORM. This study show that effective strain for flank angle, that blank diameter had important effect on the as-rolled thread while flow stress, friction factor, and crest round of dies had significant impact on effective strain at the thread root and crest and load of thread rolling. While the rate of strain harding was found to have an effect on the crest profile, the results indicate that it is the primary factor responsible for seam formation in rolled threads.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.12
• /
• pp.54-60
• /
• 2000

Research about tool condition monitoring has been done until now for product automation and unmaned system. But it is hard to apply it to the industrial field due to its cost and reliability. This paper presents the new method of tool wear measurement using Marpos gauge. This is a kind of touch sensor, so its cost is lower than vision system. And it is not affected by dust and illumination, which are important in vision system. This proposed method use tool clearance angle to measure flank wear. Experimental results compared with vision system shows that this method is available for tool condition monitoring system.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.3 no.4
• /
• pp.56-62
• /
• 2004

Using NC or CNC machine tool, the unmanned automatic production system has been growing recently in the manufacturing field. Thus it is important to find out the machinability of cutting force, tool wear and surface roughness during the cutting process. It is necessary to find how to estimate the machinability for the effective cutting condition because of problem about cutting power, tool wear, cutting time and precision. This study was planned to discover the relations of tool wear by variations of roughness and derived to correlate the wear with the surface roughness on the cutting parameter(cutting force, flank wear, surface roughness, friction angle, shear angle, slenderness ratio) when the aluminum alloy was cut in turning.

• International Journal of Internet, Broadcasting and Communication
• /
• v.16 no.1
• /
• pp.156-162
• /
• 2024

The purpose of this study was to investigate the muscle activity of internal oblique, rectus femoris, and multifidus according to knee posture and foot bar angle during pilates reformer high flank exercise. Twelve women in their 20s were recruited within six months of their experience as pilates instructors. The subjects performed six types of high flanks according to knee posture and foot bar angle. EMG signals of internal oblique, rectus femoris, and multifidus during exercise were measured and analyzed by integral EMG. The collected data were processed by repeated measures two-way ANOVA. In this paper it shows the following results. First, internal oblique iEMG was not significantly different according to knee posture and foot bar angle. Second, the rectus femoris had an interaction effect according to knee posture and foot bar angle. Third, there was no significant difference in multifidus according to knee posture and foot bar angle. In conclusion, according to the exercise method, the activity of the rectus femoris was the highest in the knee bending and high foot-bar angle high plank exercise, and there was no difference between the internal oblique and multifidus.