• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.8
• /
• pp.43-54
• /
• 1999

The effects of equivalence ratio and pressure on burnt gas temperature in premixed fuel rich propane-oxygen-inert gas combustion are investigated over the wide ranges of equivalence ration from 1.5 to 2.7 and pressure from 0.1 to 7 MPa by using a specially designed disk -type constant-voume combustion chamber, The premixtures are simultaneously ignited by eight spark plugs located on the circumference of combustion chamber with 45 degree interals. The eight converging flames compress the end gases to high pressures. The burnt gas temperature is meausured by the nmodifie dtow-colr pyrometry method. The transmissivity in the chamber center during the final stage of combustion at the hightest pressure is meausred by in situ laser extinction method. It is found that a temperature difference between the burnt gas temperature measured by mofidied and conventrational two-color method is 10 to 20 K, but the accuracy of the modified two-color methdo is higher if the local transmissivity in observed region is uniform , and the combustion at higher pressures results gas density conditions and the burnt gas temperature increases as the volume fraction of argon is increased because the specific heat of argon is lower compared to that of nitrogen with a constant equivalence ratio.

• Proceedings of the Korea Institute of Fire Science and Engineering Conference
• /
• 1997.11a
• /
• pp.518-525
• /
• 1997

A series of measurements and visualization to investigate the interaction of water sprays with pool fires is presented. Fire source is a small-scale pool burner with methanol, ethanol and gasoline. Measurements of temperatures, $O_2$, $CO_2$, and CO concentrations along the plume centerline are carried out to observe pool fire structures without water sprays. Visualization by the Ar-ion laser sheet shows flow pattern of droplets of the sprays above the pool fires. It is observed that in the case of methanol and ethanol, water sprays continuously penetrate into the center of fuel surfaces. The gasoline pool fire allows intermittent penetration of water sprays because of pulsating characteristics of the gasoline flame. To evaluate the cooling effect of the fuel surface by the sprays, the temperature was measured at the fuel surface. As soon as the mists reach the fuel surface of methanol and ethanol, the temperatures of the fuel surface decrease rapidly below the boiling point, and then the fires are extinguished. Due to the application of mist upon the gasoline fire, though the fuel temperature decrease abruptly at the time of the injection, such a rapid decrease do not continue till the extinction point.

• Journal of the Korean Wood Science and Technology
• /
• v.43 no.6
• /
• pp.768-776
• /
• 2015

This study was performed to understand combustion properties four major Indonesian wood species such as Albizia, Gmelina, Mangium and Mindi were investigated by cone-calorimeter for better utilization of theses wood species. Heat release rate (HRR), total heat release (TSR), specific mass loss rate (SMLR), effective heat of combustion (EHC), time to ignition (TTI), flame time (FT), specific extinction area (SEA), smoke production rate (SPR) and CO compound production rate were measured. HRR, THR and FT were proportional to the density of woods. Albizia showed the highest HRR, while Mindi had the lowest HRR. For SPR, Albizia showed the highest value due to its higher SEA. On the other hand, Mindi had the lowest SPR due to a lower SEA value. The highest smoke emission was for Albizia at the beginning of combustion. After 300 seconds, smoke emission of Gmleina and Mangium was increased greatly. Mangium and Mindi showed the highest total carbon dioxide emission. Expecially, Gmelina released the highest carbon monoxide during the combustion period and presented three times higher $CO/CO_2$ ratio than those of other species due to incomplete combustion.

• Journal of the Korean Wood Science and Technology
• /
• v.36 no.1
• /
• pp.45-53
• /
• 2008

The burning behaviors of board for flooring materials were investigated using cone calorimetry at an incident heat flux of $50kWm^{-2}$. Seven domestic flooring materials were used to observe the burning behavior of maximum heat release rate, total heat release and average heat release rate. The experimental data indicated that the medium density fiberboard (MDF) flooring had higher release rate than the other flooring materials. Also, the mass loss of MDF flooring was higher than the other floors. When measuring the smoke production from burning, PE fiberboard flooring and PVC Plastic Resin Sheet showed higher carbon monoxide and carbon dioxide yield than the others. The average smoke release of both carbon dioxide and carbon monoxide through specific extinction area was similar. Toxic smoke measurement from flooring materials were determined by the mouse stop motion, and the results indicated that MDF flooring contains more toxic material than the other flooring materials.

• The Journal of the Petrological Society of Korea
• /
• v.23 no.2
• /
• pp.61-73
• /
• 2014

The dextral strike-slip Yecheon Shear Zone of (E)NE-(W)SW trend is developed in the Pukhumyeon-Pyeongeunmyeon area, Gyeongsangbukdo, in the central part of Sobaeksan Massif, Korea which mainly consists of Precambrian metasedimentary rocks and Mesozoic granite. This paper researched the relative formation time, the deformation temperature, and the distribution of ultramylonite zone of Yecheon Shear Zone from the analysis of their deformed rock structures and microstructures. There are the mylonite foliation and stretching lineation by shear deformation, and the (E)SE-vergence gentle plunging, moderately inclined tight fold defined by the gneissosity and mylonite foliation as ductilely deformed main rock structures. Flame perthites, myrmekites, microfractures, microkinks, kinkband, and undulatory extinction are recognized as characteristic microstructures in feldspars during ductile shear deformation. Patterns of c-axis fabrics of recrystallized quartz aggregate display single girdle and type I crossed girdle where the rhomb and basal slip systems are predominant. The shearing senses on sense-of-shear plane show top-to-the-NE and top-to-the-SW on the predominant NW-dipping and subordinate SE-dipping mylonite foliations, respectively. These characteristic rock structures and microstructures suggest that the Yecheon ductile shearing occurred under $350{\sim}450^{\circ}C$ deformation temperature after the tight folding. The (E)NE trending ultramylonite zone of Yecheon Shear Zone, which passes through the Pulnobong and the north part of Pakdalsan, is established from the zonal distribution of Precambrian metasedimentary rocks and the grain-size distribution of feldspars in the Precambrian metasedimentary rocks and quartzs in the Mesozoic granite.