• Tribology and Lubricants
• /
• 제19권3호
• /
• pp.146-150
• /
• 2003

The natural refrigerant $CO_2$has attracted as an alternative refrigerant currently used in air conditioning system, which has high global warming potential. In this study, the tribological characteristics of the sliding surfaces between a fixed scroll and an orbiting scroll of the scroll compressor were investigated in $CO_2$/ POE mixed environment. The pin-on-disk type sliding tests were carried out under the various sliding speeds, normal loads. surface roughness, and pressures. During the test, friction forces, wear amount and surface temperature were monitored.

• 한국태양에너지학회 논문집
• /
• 제34권6호
• /
• pp.67-74
• /
• 2014

An inverter scroll compressor is used for the air conditioning in cars. Scrolls would be changed from the aluminum material to the magnesium material in order to satisfy the light weight trends of cars. The material changing influences on the scroll dimensions particularly the gap between two scrolls. Since the larger gap declines the performance of the compression, the gap between wraps of scrolls or the gap between wraps of scrolls to the plate of the opposite scroll is regarded as an important design variable. This paper is focused on the effects of the thermal stress due to the materials changing. The temperature difference between the inlet and the outlet is about 60 degrees and the highest operating temperature in the compressor is less than 110 degrees. The level of thermal stresses in the magnesium scroll is less than the result from aluminum one. The trend of the deformation is revealed that the normal directional deformation is 2 times lager than the in-plane directional deformation. Therefore the gap between the top of the wrap to the plate of the opposite scroll become more important than the other gaps. The orbiting scroll deforms larger than the fixed scroll by the thermal stresses. The deformation of the magnesium scroll is about 10% lager than that of the aluminum scroll. This value is similar to the ratio of the coefficients of thermal expansion of two materials. At the initial design stage, the results give many useful guides to engineers to propose gaps between parts.

• 설비공학논문집
• /
• 제17권4호
• /
• pp.325-332
• /
• 2005

This paper addresses the development of a scroll expander for power generation from relatively low temperature steam source. It has a double-sided orbiting scroll member so that no thrust bearing is needed to support the base plate of the orbiting scroll. Three power transmission shafts are placed at the periphery of the orbiting scroll base plate, and these shafts can also function as anti-rotation devices. Final output is obtained from the main central shaft engaged with the three power transmission shafts through gear assembly. The clearance between the fixed and orbiting scroll elements was estimated by comparing measurement of the mass flow rate with calculation results of a computer simulation. Due to large clearance, the expander total and volumetric efficiencies were measured to be $34\%\;and\;43\%$, respectively. It has been shown through the computer simulation that the total and volumetric efficiencies could be improved to $65\%\;and\;83\%$, respectively, if the current clearance is reduced by half.

• 소성∙가공
• /
• 제26권3호
• /
• pp.156-161
• /
• 2017

In this study, the reason of die fracture occurring in hot forging of an aluminum fixed scroll was studied, based on experiments and finite element predictions. The material is assumed to be rigid-viscoplastic, and the die is rigid for the finite element predictions. The stress in the tension at the wrap root is known to cause brittle fracture, and the increase in the tensile stress is owing to the unbalanced filling of material into the die cavities between both sides of the warp. Based on the empirical and numerical achievements, the effects of geometrical parameters of the material on the die fracture were examined to find practical measures for elongated die life. It has been shown from the parametric study that the material with the optimized trapezoidal cross-section, which can be easily made during cutting or the optimized cylindrical billet with its eccentric placement in the die cavity, can considerably reduce the magnitude of the tensile stress around the die corner fractured, indicating that economical manufacturing with reduced number of stages and elongated die life can be realized at once using the optimized practical initial material.

• 설비공학논문집
• /
• 제29권3호
• /
• pp.127-133
• /
• 2017

Performance analysis has been carried out on a high side scroll compressor that had a fixed scroll equipped with a circular oil groove on its thrust surface. Oil was supplied to the oil groove through an intermittent opening from a high pressure oil reservoir formed inside the orbiting scroll hub. Oil in the groove was then delivered to both suction and back pressure chambers by pressure differentials and viscous pumping action of the orbiting scroll base plate. Mathematical modeling of this oil groove system was incorporated into a main compressor performance simulation program for an optimum oil groove design. The study findings were as follows. Pressure in the oil groove can be controlled by changing its configuration and the oil passage area. With an enlarged oil passage, the pressure in the oil groove heightens due to an increased flow rate, but the pressure elevation in the back pressure chamber is small, resulting in reduced friction loss at the thrust surface between the two scrolls. On the other hand, by increasing the oil passage area, the oil content in the refrigerant flow increases. Considering all these factors, the energy efficiency ratio could be improved by about 3.6% under the ARI condition by an optimal oil groove design.

• 설비공학논문집
• /
• 제12권2호
• /
• pp.181-189
• /
• 2000

The scroll compressor used for heat pump has a wide range of operation condition. To cover both heating and cooling modes, the operating Pressure ratio ranges from 1.5 to 6.8. Since the scroll compressor, however, is a type of compressor whose pressure ratio is fixed, some loss in the compression work is caused by the operation at the pressure ratio different from the built-in pressure ratio. A way of avoiding this problem is to introduce by-Pass holes in compression chambers, so that the compressed gas of pressure higher than the discharge pressure, yet not reached to the discharge port can be released earlier through the by-Pass holes. In this paper, an optimum Positioning of the by-Pass hole and the effect of the by-pass valve on the compressor performance are studied.

• 소성∙가공
• /
• 제22권4호
• /
• pp.183-188
• /
• 2013

Scroll compressors are widely used in air conditioning systems and in automobiles due to their low pressure loss, minimal vibrations, and light-weight. Open-die forging with back pressure is used to forge the rotating scroll, and it requires special care since the forging die can be severely damaged at the fixed end of the spiral cavity similar to a fracture of a cantilever beam. To overcome the inevitable weakness of the forging die due to such damage, an innovative design is necessary. In this study, structural analysis using the finite element method was conducted to determine the reason for the fracture of the forging die. A novel design to avoid stress concentrations and vertical deflection, causing serious damage to the die, is suggested.

• 컴퓨터교육학회논문지
• /
• 제5권4호
• /
• pp.134-145
• /
• 2002

본 연구는 학습자가 전자교과서에서 문자별로 초점이 다른 텍스트요인을 학습시 내용흐름에 따라 편하게 읽을 수 있게 하기 위한 기능 및 기술적 방안을 제시한다. 본 연구에서 제시한 전자교과서의 텍스트 화면은 학습자가 전자교과서의 텍스트를 접할 때 설정된 값 이상의 데이터가 디스플레이 되면 마우스나 키보드의 작동 없이 학습자별로 원하는 형태로 자동으로 스크롤되어 쉽게 읽을 수 있게 된다. 또한 학습내용이나 개인차에 따라 제시방법이나 속도를 수시로 제어할 수 있다. 자동 텍스트 스크롤은 텍스트 내용구조(특정 및 영역 분류 등), 제시형태(밀도, 사이즈, 폰트 등), 제시방법(스크롤방법, 속도 등), 프로그램 통제유형(램 상주 등)과 화면디자인 적용(가독성 등)등에 따른 데이터 및 화면의 자동 스크롤 방법으로 텍스트 학습에 대한 개인의 능력 및 성향을 반영할 수 있다. 이를 위한 기술적 해결책을 환경설정단계, 스크롤지정단계, 복사단계, 데이터분석단계, 스크롤코딩단계, 중앙포커스코딩단계, 좌우포커스코딩단계, 실행단계로 나누어 제시하였다.

• 한국산학기술학회논문지
• /
• 제17권9호
• /
• pp.718-723
• /
• 2016

중형 차량용 에어컨에 사용되는 스크롤 압축기는 토크변동이 적고 에너지 효율이 높으며, 소음이 적어 적용이 확대되어 가고 있다. 또한 경량화에 따라 압축기를 구성하는 주요부품이 스틸에서 알루미늄으로 변경하는 등 소재에 대한 연구가 활발히 이루어지고 있다. 또한 스크롤 압축기는 고정 스크롤과 선회 스크롤의 인벌루트 랩의 가공 정밀도가 $10{\mu}m$ 이하로 정밀도가 높은 전용장비와 전용 툴은 물론 숙련된 가공기술이 요구되므로 가공 품질을 확인하기 위하여 표면조도와 윤곽도를 측정하였으며, 알루미늄을 모재로하여 양극 산화 처리하여 사용되고 있는 선회스크롤의 경도를 향상시키기 위한 방법의 일환으로 봉공처리를 수행에 따른 특성들을 살펴보았다. 알루미늄 소재는 Al-Mg-Cu계 합금으로 미량의 Ni, Fe, Zn 이 부가된 것으로 나타났으며, 표면조도는 $3{\mu}m$이하로 가공 정밀도 기준 $10{\mu}m$를 만족하였다. 또한 양극산화 후 나노다이아몬드, CNT로 봉공처리 한 경우 경도는 450 이상으로 수봉공처리의 경우 보다 50% 이상 경도가 향상됨을 알 수 있었으며, 봉공재로 사용하기 위한 소재로서 탄소나노튜브나 나노다이아몬드는 큰 차이를 보이지 않았다.

• 한국HCI학회:학술대회논문집
• /
• 한국HCI학회 2008년도 학술대회 1부
• /
• pp.147-151
• /
• 2008

모바일 기승의 발전으로 기존 PC 화면 기반으로 개발된 기능들이 모바일의 작은 화면으로 옮겨짐으로 인해 큰 화면의 정보를 작은 화면에 동일하게 표현하기 위해서 모바일 기기 화면상에 많은 가로 스크롤이 발생하게 되었다. 가로 스크롤로 인해 모바일 기기의 작은 화면으로 문서를 읽을 때 현재 읽고 있는 줄의 위치를 놓치는 오류가 발생하게 되었으며, 이러한 줄 이탈 오류로 인해 문서의 가독성이 떨어지게 되었다. 본 논문에서는 모바일 기기의 가독성을 높이기 위해서 Line Marker를 제안 하였으며, 실험을 통해서 Line Marker가 없는 조건, 이동하는 Line Marker 조건, 고정된 Line Marker 조건에 따른 문서의 읽기 속도와 읽기 방식에 따른 만족도를 평가하였다.