• 복합신소재구조학회 논문집
• /
• 제6권4호
• /
• pp.44-50
• /
• 2015

The finite element analysis of large sized rectangular water tank structures made of stainless steel materials is carried out for various combined load cases. The combined load cases for a large size of 5,000ton are further determined using the specification(KS B 6283) established from the Korean Standards Association. For the better numerical efficiency, the rectangular panels are modelled using the ANSYS program. The numerical results obtained for different load cases show as follows. In order to resist the snow load, it takes the influence of the gap than the size of the column. Also, in order to resist the water pressure, it shall increase the thickness of the wall. But, increasing the thickness of the wall is considerably less economical. Therefore, the angle with big thickness should be placed right next to the wall.

• 한국전기전자재료학회논문지
• /
• 제20권5호
• /
• pp.425-429
• /
• 2007

A linear ultrasonic motor was designed by a combination of the longitudinal and bending mode. linear ultrasonic motors are based on an elliptical motion on the surface of elastic body, such as bar or plates. The corresponding eigen-mode of one resonance frequency can be excited twice at the same time with a phase shift of 90 degrees in space and time. That is excite symmetric and anti-symmetric modes. Then it determines the thrust and speed of the motor. Linear ultrasonic motors are investigated experimentally in according to be fabricated a general classification to motor structure and material characteristic. There was the first to simulate as use of finite element analysis ANSYS 9.0. The AL-T2W8-ARM14-LEG18-ANGLE80 motor has a maxim efficiency 18 % under the speed 0.14 m/s, thrust 345 gf and preload 280 gf, operating frequency is 57.6 kHz.

• Wind and Structures
• /
• 제29권5호
• /
• pp.361-369
• /
• 2019

The modal frequency responses of adhesive bonded T-joint structure have been analyzed numerically and verified with own experimental data. For this purpose, the damped free frequencies of the bonded joint have been computed using a three-dimensional finite element model via ANSYS parametric design language (APDL) code. The practical relevance of the joint structure analysis has been established by comparing the simulation data with the in-house experimental values. Additionally, the influences of various geometrical and material parameters on the damped free frequency responses of the joint structure have been investigated and final inferences discussed in details. It is observed that the natural frequency values increase for the higher aspect ratios of the joint structure. Also, the joint made up of Glass fiber/epoxy with quasi-isotropic fiber orientation indicates more resistance towards free vibration.

• 대한치과보철학회지
• /
• 제35권1호
• /
• pp.181-210
• /
• 1997

The stress distribution generated in the surrounding bone was calculated and compared for various geometry of the dental implants by means of the finite element methods. The models were designed to represent the screw type endosseous implants(varing the size, shape, direction of the screw thread and the angle of the body) with supporting bone and the cylinder type endosseous implants(varing the lower portion-Round type, tapered type) with supporting bone. Static mean bite forces were applied 100N vertically and 25N horizontally on the center of the implant and three dimensional finite analysis was undertaken using software ANSYS 5.1 Version. The result demonstrated that different implant shape leads to significant variations in stress distribution in the bone. In the case of variation of the screw size, direction and shape the implant model with normally directional and triangular screw implied lower stress than with upper directional or lower directional and quadrangular screw but among models a different screw size, within a variation of 0.2mm there was no meaningful difference in maximum stress. In the case of variation of angle of body the straight implied lower stress than the tapered. As a result of analysis of cylinder type, the implants with larger radius of curvature of the round form and larger diameter of the tapered form implied lower stress.

• Restorative Dentistry and Endodontics
• /
• 제33권6호
• /
• pp.570-579
• /
• 2008

이 연구의 목적은 쐐기형 5급 와동과 근관와동을 복합레진으로 수복한 상악 제2소구치에 대한 응력 분포를 3차원 유한요소법으로 분석하여 평가하기 위한 것이다. 발치된 상악 제2소구치를 이용하여 Micro-CT로 스캔한 후 3D-DOCTOR로 3차원 유한요소 모형을 제작하였다. 제작된 소구치 모형에 근관 와동을 형성하고 쐐기형 5급 와동과 글래스 아이오노머 기저재의 사용 여부를 구분하여 근관 와동을 혼합형 복합레진으로 충전하였다. 협측 교두 또는 설측 교두에 500 N의 하중을 가하고, ANSYS 8.0 프로그램으로 인장 응력의 분포를 분석하여 평가한 결과 베이스 사용유무에 따른 응력 분포의 차이는 없었다. 협측 교두에 하중이 가해질 때, 하중점과 교합면의 중심구, 구개측 백악법랑경계부에 과도한 인장 응력이 집중되었으며, 5급 와동이 없는 경우보다 5급 와동이 있는 경우에 약간 더 높았다. 설측 교두의 협측 경사면에 하중이 가해질 때, 하중점과 교합면의 중심구, 협측 치경부에 과도한 인장 응력이 집중되었으며, 5급 와동이 있는 경우가 5급 와동이 없는 경우보다 약간 더 낮았다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 춘계학술대회 논문집
• /
• pp.497-502
• /
• 2002

This paper describes a design methodology of a tri-axial silicon-based farce sensor with square membrane by using micromachining technology (MEMS). The sensor has a maximum farce range of 5 N and a minimum force range of 0.1N in the three-axis directions. A simple beam theory was adopted to design the shape of the micro-force sensor. Also the optimal positions of piezoresistors were determined by the strain distribution obtained from the commercial finite element analysis program, ANSYS. The Wheatstone bridge circuits were designed to consider the sensitivity of the force sensor and its temperature compensation. Finally the process for microfabrication was designed using micromachining technology.

• 한국가스학회지
• /
• 제13권3호
• /
• pp.1-6
• /
• 2009

최근 화학 산업이 발전함에 따라 고압설비가 널리 이용되고 있다. 이러한 고압 설비는 편리성과 함께 많은 위험을 내포하고 있다. 파열판 안전장치는 고압설비의 안전사고로부터 설비와 생명을 보호하는 장치이다. 파열판 안전장치는 홀더, 파열판, 버큠서포트로 구성되어져 있으며, 다양한 환경 조건에서 부식되거나 파괴되는 단점이 있다. 본 논문에서는 부식 저항성이 우수하여 파열판 안전장치의 소재로 많이 사용되고 있는 STS 316L stainless steel 소재를 이용해서 제작한 파열판 안전장치를 CATIA V5를 이용하여 3차원 모델링을 수행하고, 유한요소해석을 통하여 소재의 두께와 높이에 따라 파열판 안전장치의 파열에 영향을 미치는 요인을 분석하였다.

• Steel and Composite Structures
• /
• 제48권1호
• /
• pp.43-57
• /
• 2023

The impacts of waste tire rubber (WTR) on the bending conduct of reinforced concrete beams (RCBs) are investigated in visualization of experimental tests and 3D finite element model (FEM) using both ANSYS and SAP2000. Several WTR rates are used in total 4 various full scale RCBs to observe the impact of WTR rate on the rupture and bending conduct of RCBs. For this purpose, the volumetric ratios (Vf) of WTR were chosen to change to 0%, 2.5%, 5% and 7.5% in the whole concrete. In relation to experimental test consequences, bending and rupture behaviors of the RCBs are observed. The best performance among the beams was observed in the beams with 2.5% WTR. Furthermore, as stated by test consequences, it is noticed that while WTR rate in the RCBs is improved, max. bending in the RCBs rises. For test consequences, it is clearly recognized as WTR rate in the RCB mixture is improved from 0% to 2.5%, deformation value in the RCB remarkably rises from 3.89 cm to 7.69 cm. This consequence is markedly recognized that WTR rates have a favorable result on deformation values in the RCBs. Furthermore, experimental tests are compared to 3D FEM consequences via using ANSYS software. In the ANSYS, special element types are formed and nonlinear multilinear misses plasticity material model and bilinear misses plasticity material model are chosen for concrete and compression and tension elements. As a consequence, it is noticed that each WTR rates in the RCBs mixture have dissimilar bending and rupture impacts on the RCBs. Then, to observe the impacts of WTR rate on the constructions under near-fault ground motions, a reinforced-concrete building was modelled via using SAP2000 software using 3-D model of the construction to complete nonlinear static analysis. Beam, column, steel haunch elements are modeled as nonlinear frame elements. Consequently, the seismic impacts of WTR rate on the lateral motions of each floor are obviously investigated particularly. Considering reduction in weight of structure and capacity of the members with using waste tire rubber, 2.5% of WTR resulted in the best performance while the construction is subjected to near fault earthquakes. Moreover, it is noticeably recognized that WTR rate has opposing influences on the seismic displacement behavior of the RC constructions.

• 소음진동
• /
• 제8권5호
• /
• pp.936-948
• /
• 1998

A theoretical formulation for the analysis of free vibration of a cylindrical shell with a circular plate attached at an arbitrary axial position of the shell under various kinds of boundary conditions was derived and programed to get the numerical results for natural frequencies and mode shapes of the combined system. The boundary conditions of the shell to be considered here are clamped-free, clamped-simply supported, both ends clamped and both ends simply supported. The frequencies and mode shapes from theoretical calculation were compared with those of commercial finite element code, ANSYS. The results showed good agreement with those of ANSYS in frequencies and mode shapes. The program will contribute to the design optimization of a shell/plate combined system through the analysis of natural frequencies and mode shapes for the system.

• 복합신소재구조학회 논문집
• /
• 제6권2호
• /
• pp.85-90
• /
• 2015

The finite element stress analysis of large sized rectangular water tank structures made of stainless steel materials is carried out for various combined load cases. The combined load cases for a large size of 5,000ton are further determined using the specification(KS B6283) established from the Korean Standards Association. The changed water capacity due to the size of reservoirs could be heavily dependent for evaluating seismic effects, especially for large reservoirs. For the better numerical efficiency, the rectangular panels are modelled using the ANSYS ADPL module. The numerical results obtained for different load cases mainly show the effect of the interactions between the different load combination and other various parameters, for example, the water capacity, and different stainless steel materials. The structural performance for various load combinations is also evaluated.