• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2001년도 가을 학술발표회 논문집
• /
• pp.623-628
• /
• 2001

The objective of this study is to find out the effect of Horizontal vibration on the compressive strength for 7 days and 28 days cured concrete specimens according to the kind of fine aggregates and the variation of vibration velocities, and times began to vibrate. Three kinds of fine aggregate(river sand, sea sand, crush sand), three types of vibration velocities(0.25, 0.5 0.1kine(cm/sec)), and four steps of times(0, 3, 6, 9 hours after concrete casting) were chosen as the experimental parameters in this study, the vibrations are applied for 30 minutes in each case. From this study, the variation with type of fine aggregate doesn't show tendency and the compressive strength decreases with increasing vibration velocity. When the vibration force time is more than 6 hour, It shows that compressive strength decreases under the condition of vibration velocity which the value is 0.5 kine and 1 kine, respectively.

• Journal of the Optical Society of Korea
• /
• 제20권6호
• /
• pp.762-769
• /
• 2016

The dynamic modulation transfer function (MTF) for image degradation caused by sinusoidal vibration is formulated based on a Bessel function of the first kind. The presented method makes it possible to obtain an analytical MTF expression derived for arbitrary frequency sinusoidal vibration. The error obtained by the use of finite order sum approximations instead of infinite sums is investigated in detail. Dynamic MTF exhibits a stronger random behavior for low frequency vibration than high frequency vibration. The calculated MTFs agree well with the measured MTFs with the slant edge method in imaging experiments. With the proposed formula, allowable amplitudes of any frequency vibration are easily calculated. This is practical for the analysis and design of the line-of-sight stabilization system in the remote sensing camera.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2001년도 봄 학술발표회 논문집
• /
• pp.304-312
• /
• 2001

The objective of this study is to find out effects of horizontal vibration on the compressive strength for 7days and 28 days cured concrete specimens according to the variation of fine aggregate modului, vibration velocities, and times began to vibrate. Four kinds of fine aggregate modului(40, 42, 45, 47%), three of vibration velocities(0.25, 0.5 0.1kine(cm/sec)), and four of times(0, 3, 6, 9hrs after concrete casting) were chosen as the experimental parameters in this study, the vibrations were applied for 30 minutes in each case. From this study, it could be seen that the most increase of compressive strengths were obtained in case of 47% fine aggregate modulus, and 0.25kine of vibration velocity, but the strength was decreased when vibrated after 9hrs from concrete casting.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 추계학술대회 논문집
• /
• pp.799-800
• /
• 2010

• 한국소음진동공학회논문집
• /
• 제17권9호
• /
• pp.805-812
• /
• 2007

This paper present a robust controller design method based on the estimation of velocity disturbance to construct a robust fine seek control system. A loop gain adjustment algorithm is introduced to accurately estimate the velocity disturbance in spite of the uncertainties of fine actuator. A weighting function is optimally selected from a minimum fine seek open-loop gain, calculated by estimating the velocity disturbance. A robust fine seek controller is designed by considering a robust $H_{\infty}$ control problem using the weighting function. The proposed controller design method is applied to the fine seek control system of a DVD rewritable drive and is evaluated through the experimental results.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 추계학술대회논문집
• /
• pp.236-241
• /
• 2004

In this paper, the dual stage interaction between the coarse actuator and the fine actuator of an optical disk drive and the control method to enhance the track pull-in performance are discussed. First, the interaction analyses for the dual stage, and the experiments to find the each actuator dynamics are studied. From the experiments results, some physical parameters was derived, then, some simulations are performed to find the residual vibration effect of the fine actuator during seek motion. Second, the fine actuator control method to reduce the relative velocity, which is a key factor in track pull-in performance, between the target track and beam spot is proposed. From simulations, we show that fine actuator control which has same frequency and same phase of the disturbance is effective to reduce the relative velocity, hence, the control method is good approach in the track pull-in enhancement. Finally, the some comments are discussed briefly.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2009년도 추계학술대회 논문집
• /
• pp.324-325
• /
• 2009

• 한국정밀공학회지
• /
• 제10권1호
• /
• pp.126-133
• /
• 1993

Conventional cutting(CC) and Ultrasonic Vibration Cutting(UVC) of 20[KHz] are practised with standard lathe for fine ceramics(A1$_{2}$O$_{3}$. UVC is suggested to good cutting method for difficult-to-machine-materials and it is known to excellent cutting method to super precision cutting and elevation of productibility for general, nonferrous matals. In this research, main results to be obtained are as follows: 1. From the CC and UVC results by general lathe with sintering diamond tool, the surface roughness and roundness are improved in UVC. Also tool life is longer in UVC than CC. From the observation of machined surface, it is found that brittle fracutural material remove occured in fine ceramics cutting. 2. It is verified that the thrust force is the biggest in fine ceramics cutting, principal force is the next, and feed rate force the third and it is appear a little, on the other hand the principal force is the biggest in metal cutting, feed rate frece is the second, and thrust force is the next.

• 한국소음진동공학회논문집
• /
• 제15권11호
• /
• pp.1276-1286
• /
• 2005

In this paper, the dual stage interaction between the coarse actuator and the fine actuator of an optical disk drive is studied, and the new control method to enhance the track pull-in performance using fine actuator control is proposed. First, the dynamic analysis for the dual stage and the experiments to find the each actuator dynamics are performed. From the experiments, some physical parameters of the actuators were derived, then, some simulations are performed to find the interaction effect of the fine actuator during seek motion. Second, the center servo which suppresses the vibration of fine actuator during seek motion is designed and evaluated. And the fine actuator control to reduce the relative velocity between the target track and beam spot is proposed. From simulations, we show that fine actuator control which has same frequency and same phase of the disturbance is effective to reduce the relative velocity, and this result leads to track pull-in enhancement. Hence, the proposed control method is good approach to improve the track pull-in performance. Finally, the realization of the proposed method and some comments of it are briefly discussed.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2003년도 추계학술대회논문집
• /
• pp.220-225
• /
• 2003

Recent issue of optical actuator is applying to mobile device. It leads actuator to become smaller than conventional type. This paper proposes the design of micro actuator plate spring and analysis of its vibration characteristic. Considering natural frequency of spindle motor, 1st and 2nd eigenfrequency of micro actuator must avoid its natural frequency. First, magnetic circuit is designed by using fine pattern coil and magnetic force is acquired by simulation program. Then, concept design is achieved by topology optimization. From concept design, micro actuator plate spring is embodied through DOE(design of experiment). Finally, considering vibration characteristic simultaneously, optimal plate spring design is determined by RSM(response surface method).