• Journal of the Korean Society for Nondestructive Testing
• /
• v.23 no.3
• /
• pp.220-226
• /
• 2003

This paper presents the result of an investigation on the application of the acoustic emission method to the monitoring of fatigue crack initiation, growth and track location in welded joints. Fatigue test was carried out for a typical fillet welded joint of ship structure. AE parameter such as ring down count was analyzed in time domain and crack locations were examined by source location and cluster option which is one of the functions of AE signal processor The usability of AE mettled was confirmed for the detection of the initiation and location of through crack.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.4
• /
• pp.127-131
• /
• 2010

Stainless steel sheets are widely used as the structural material for the railroad cars and the commercial vehicles. These kinds of structures used stainless steel sheets are commonly fabricated by using the gas welding. For fatigue design of gas welded joints such as fillet and plug type joint, it is necessary to obtain design information on stress distribution at the weldment as well as fatigue strength of gas welded joints. And also, the influence of the geometrical parameters of gas welded joints on stress distribution and fatigue strength must be evaluated. Thus, in this paper, ${\Delta}P-N_f$ curves were obtained by fatigue tests. Using these results, ${\Delta}P-N_f$ curves were rearranged in the. ${\Delta}{\sigma}-N_f$ relation with the hot spot stresses at the gas welded joints.

• Journal of Welding and Joining
• /
• v.30 no.6
• /
• pp.62-67
• /
• 2012

In this study, the bonding strengths of adhesively bonded joints are experimentally investigated. A series of lap-shear tests are conducted using single lap type adhesive joints. In order to analyse the joint fabrication factors that affected the bonding strength, the parametric tests are conducted with various thickness of adhesive, surface roughness and fillet of adhesive. In addition, for the comparative study with the welded joint, lap-shear tests using specimens with 2 welded sides and 4 welded sides are also carried out. The quantitative results of the strength analysis are summarized, and some proposals are made on setting up testing standards for adhesively bonded joints.

• Journal of Welding and Joining
• /
• v.28 no.4
• /
• pp.49-54
• /
• 2010

Stainless steel sheets are widely used as the structural material for the railroad cars and the commercial vehicles. These kinds structures used stainless steel sheets are commonly fabricated by using the GMAW (gas metal arc welding). For fatigue design of GMA welded joints such as fillet and plug, ring type joint, it is important to obtain optimum design factor information on GMA welded joints. in this paper, analysis approach for fatigue test using design of experiment are evaluated optimum factor in GMA welded joint type and geometrical parameters of materials. Using these results, that factors applied to fundamental information for fatigue design.

• Journal of the Korean Institute of Gas
• /
• v.17 no.1
• /
• pp.19-25
• /
• 2013

The joining methods of steel structures of gas facilities, bridges, ships etc. by welding are composed mostly of T-type or cruciform fillet welding and full penetration or partial penetration according to the uses and the shape of the structures. In this study, it was examined the characteristics of fatigue crack according to penetration depth in relation to material thickness in the cruciform fillet welded joints. From the results, it was investigated the safe design stresses within the range of infinite life. When the LOP length is long the range of infinite life is small with root failure and when the LOP length is short the range of infinite life is large with teo failure. For the specimen of material thickness, 20mm welded by 3 pass compared with 10mm, 15mm welded by 2 pass, the fatigue strength and the range of infinite life was more improved by increasing of notch toughness from formation of micro-ferrite acicular structure.

• International Journal of Korean Welding Society
• /
• v.5 no.1
• /
• pp.60-65
• /
• 2005

In the field of welding the mechanical behavior of a welded structure under consideration may be predicted via heat transfer and welding residual stress analysis. Usually such numerical analyses are limited to small regular mesh models or test specimens. Nevertheless, there is very few strength assessment of the whole structure that includes the effect of welded residual stress. The present work is based on the specialized finite element codes for the calculation of nonlinear heat transfer details and residual stress including the external load on the welded RHS (Rectangular Hollow Section) T-joint connections of the whole structure. First the thermal history of the combined fillet and butt-welded T-joint equal width cold-formed RHS are calculated using nonlinear finite element analysis (FEA) considering the quarter model of the joint. Then using this thermal history the residual stress around the joints has been evaluated. To validity the FEA result, the calculated residual stresses were compared with the available experimental results. The residual stress obtained from the quarter model is mapped to the full model and then to the whole structure model using FEM codes. The results from the FEM codes were exported to the commercial package for visualization and further analysis applying loads and boundary conditions on the whole structure. The residual stress redistribution along with the external applied load is examined computationally.

• International journal of steel structures
• /
• v.18 no.5
• /
• pp.1631-1638
• /
• 2018

In the periodic repainting of steel bridges, often the steel surface has to be prepared by using power tools to remove surface contaminants, such as deteriorated paint film and rust, and to increase the adhesive strengths of the paint films to be applied newly. Surface preparation by bristle roll-brush grinding, which is a type of power tool, may additionally introduce compressive residual stress and increase the fatigue resistance of welded joints owing to the impact of rotating bristle tips. In this study, fatigue tests were conducted for longitudinally out-of-plane gusset fillet welded joints and transversely butt-welded joints to evaluate the effect of bristle roll-brush grinding prior to repainting on the fatigue resistance of the welded joints. The test results showed that bristle roll-brush grinding introduced compressive residual stress and significantly increased fatigue limits by over 50%.

• Journal of Korean Society of Steel Construction
• /
• v.14 no.2
• /
• pp.311-318
• /
• 2002

This paper described the ultimate strength and deformation limit of welded T-joints in cold-formed square hollow sections. Previous studies showed that the strength of a T-joint still increases with increasing deformations at a ratio of branch width to chord width (${\beta}$) of below 0.8. Therefore, the strength at a certain deformation (chord flange indentation) limit can be regarded as the ultimate strength of a T-joint. The chord flange failure modes were investigated for the ratio of branch width to chord width (${\beta}$) and the ratio of chord width to chord web thickness (B/T). Experimental results including tests done by Kato proposed a deformation limit of 3%B for $16.7{\leq}B/T{\leq}41.6$ and $0.27{\leq}{\beta}{\leq}0.8$. The strength formula of CIDECT and other researchers were compared with the test results. Finally, the strength formula based on yield-line theory was proposed.

• Journal of Korean Society of Steel Construction
• /
• v.21 no.1
• /
• pp.55-62
• /
• 2009

Blast cleaning has been applied in steel bridges for cleaning forged surface and increasing adhesive property of applied coating systems. Blasting is the operation of cleaning or preparing a surface by forcible propelling a stream of abrasive metals against it. Blast cleaning may improve surface geometry and induce compressive residual stress, and eventually may increase fatigue life of weld joints. In this paper, fatigue tests were carried out on three types of non-load-carrying fillet welded cruciform joints, as-welded joints, blast-treated joints, and stress-relieved joints after blasting, in order to investigate effect of blast cleaning on fatigue behavior of the weld joints. By Blast cleaning, the weld toe radius was increased by 29% and compressive residual stress was induced near weld toes. Blast cleaning increased fatigue life and fatigue endurance limit of the weld joints. When the applied stress ranges decreased, the increment in fatigue life became larger. About a 150% increase in fatigue limit could be realized by using blast cleaning.

• Journal of Welding and Joining
• /
• v.29 no.4
• /
• pp.67-72
• /
• 2011

The proportion of the welding in the production process of machinery, buildings and marine structures is increasing and the joining are mainly conducted by butt and fillet weld. In the case of fillet weld, the shape of structures is complicated depending on the constraint on the geometry of the structures, therefore, the full penetration is mostly difficult. Accordingly, it is necessary to establish safe and economical criteria of design of the structures through the strength based on the penetration state of the fillet weld. Patterns of fatigue failure in cruciform fillet weld jont appear in the form of the root, toe and mixed failure. In the case of toe and mixed failure, the fatigue strength is higher than root failure. Therefore, we have to make the enough depth of penetration or perform the welding work through improving the fatigue strength of cruciform joints in welded structures. So it is necessary to optimize the penetrated depth in the range of the possible mixed failure and find the way in the cost-effective design to lessen the amount of the welding work.