최근 산업의 발달로 증가하는 도로와 이를 이용하는 차량의 증가로 인한 교통사고가 지속적으로 증가하고 있다. 교통사고는 운전자과실, 차량결함, 주행도로상태, 자연환경 등의 다양한 불안정 인자들로 인하여 발생한다. 방호울타리의 한 종류인 가드레일은 교통사고 및 이탈을 방지하여 탑승자의 상해와 차량의 파손을 최소로 줄여 차량을 정상주행 시키는 것을 목적으로 한다. 가드레일은 8 tonf 차량이 $15^{\circ}$로 80 km/h의 속도로 가드레일에 충돌하는 시험으로 가드레일의 안정성을 평가하며, 지반은 상대적으로 지지력이 큰 무한평지에서 평가된다. 하지만 국내의 경우 성토사면에 설치된 가드레일은 보호길어깨에 설치되며, 이로 인해 가드레일의 지지력 저하 및 성능저하로 가드레일의 안정성에 문제가 발생할 가능성이 있다. 이러한 가드레일에 대한 기존 연구는 무한평지에 설치된 가드레일 및 차량의 안정성에 대한 연구가 수행되었다. 하지만 차량 충돌 시 가드레일이 설치된 성토사면의 거동에 대한 연구는 미비한 실정이다. 이에 본 연구에서는 차량 충돌 시 성토사면의 거동을 확인하기 위해 유한요소프로그램인 LS-DYNA를 이용하여 성토사면에 설치된 가드레일의 지주 매입깊이를 변화시켜 수치해석을 수행하였다. 그리고 수치해석은 NCAN(National Crash Analysis Center)에서 제공하는 8 tonf 트럭을 이용하여 성토사면에서 가드레일 지주의 매입깊이를 변화시키면서 충돌 해석을 수행하였다. 그 결과, 가드레일 지주의 매입깊이가 증가함에 따라 성토사면의 변위와 응력이 증가하는 것으로 나타났으며, 450 mm 깊이에서 지반지지력이 저하되는 것으로 나타났다.
댐의 경과년수에 따라 고장으로 폐기되는 매설계기의 지속적인 증가로 인해 기존 필댐의 유지관리를 위한 계측시스템의 재정립이 필요한 상황이지만 필댐의 파괴모드와 계측기의 중요도에 대한 체계적이고 정량적인 분석 없이 과거의 경험과 소수 전문가의 자문의견에만 의존하여 유지관리 계측계획을 수립하고 있는 실정이다. 본 연구에서는 선행연구(Andersen 등, 1999)를 기초로 하여 5개 기존 필댐 계측항목의 중요도를 정량적으로 분석하여 우선순위를 산정한 결과로서 상세 외관조사와 함께 침투수량계, 표면 침하점, 간극수압계에 대한 상시 모니터링 체계의 구축을 기존 필댐 계측시스템의 재정립 방안으로 제시하였으며 이것은 일본토목연구소(1984), 일본 대댐회(국토교통성, 1986)의 권고사항과 Bagherzadeh-Khakkahali와 Mirghasemi(2005)의 분석결과와도 잘 일치하는 것으로 나타났다.
본 연구의 목적은 필댐의 중요 계측항목인 침투수량계에 대해서 의사결정나무 분석을 통해 관리기준을 제시하는 것이다. 국내 댐의 침투수량의 경우는 강수시 하류사면 및 양안으로부터 강수의 직접적인 유입이 발생하여 침투수량이 급증하는 현상이 발생한다. 따라서 강수를 고려한 필댐의 관리기준이 필요한 설정이다. 본 연구에서는 국내 필댐 1개소에 대해 침투수량을 반응변수로 하고 강수량 및 저수위를 설명변수로 설정하여 의사결정나무 분석을 수행하였다. 그 결과 강수량 34.75mm/day 이하의 조건에서부터 저수위가 설명변수로서 작용하였고 저수위의 분기조건은 37.4m, 35.23m로 분석되었다. 강수량 34.75mm/day 이하의 조건에서 침투수량 자료의 98%가 분포하며, 해당 집단의 평균값은 13.25L/min~24.24L/min으로 나타났다. 침투수량에 대한 영향인자로서 강수량 및 저수위를 선택하는 경우 강수량의 영향이 지배적이었고 강수 및 저수위별 평균 침투수량의 관리기준이 제안되었다.
This paper presents an approach to Mongolian car plate recognition using artificial neural network. Our proposed method consists of two steps: detection and recognition. In detection step, we implement Flood fill algorithm. In recognition step we proceed to segment the plate for each Cyrillic character, and use an Artificial Neural Network (ANN) machine - learning algorithm to recognize the character. We have learned the theory of ANN and implemented it without using any library. A total of 150 vehicles images obtained from community entrance gates have been tested. The recognition algorithm shows an accuracy rate of 89.75%.
20 million tons of coal ash has been produced in Korea annually. This causes the environmental problems and the cost of land for ash pond. However the amount of coal ash for recycling is small because of the low level of recycling technology and the ignorance. As the coal ash has the significant engineering properties, it can be utilized as soft ground stabilizer, backfill materials and so forth. The purpose of this paper is to summarize some of the recycling methods of coal ash. One is structural backfill materials, the other is flowable fill. Optimal mixture ratio(fly ash : bottom ash) is determined for structural backfill materials and the model test is performed. The model test accompanied with physical tests were executed for identifying that the flowable fly ash can be used as fill materials such as trench back filling.
The deposition process for the gap-filling of sub-micrometer trenches using DMDMOS, $(CH_3)_2Si(OCH_3)_2$, and $C_xH_yO_z$ by flowable chemical vapor deposition (F-CVD) is presented. We obtained low-k films that possess superior gap-filling properties on trench patterns without voids or delamination. The newly developed technique for the gap-filling of submicrometer features will have a great impact on IMD and STI for the next generation of microelectronic devices. Moreover, this bottom up gap-fill mode is expected to be universal in other chemical vapor deposition systems.
해성점토를 이용하여 준설매립한 부지의 장기적인 침하거동을 규명하기 위하여 실린더와 대형토조를 이용하여 침강.자중압밀시험을 수행하였으며, 준설매립단지에 자동무선계측시스템을 설치하여 매립부지의 층별침하량과 간극수압의 변화를 계측하였다. 이를 이용하여 준설매립 공정에 따른 매립지층의 침하거동을 분석하고 유한변형률 압밀이론을 이용한 수치해석 결과와 비교하였다. 침하거동 분석결과, 불연속 준설매립공정으로 인하여 매립지층의 분리 현상이 발생하였고 지층별 침하거동이 상이하게 나타났다.
When surface Concrete Face Rock fill Dam constructs than existent center core type rock fill dam, it is much prevalent form in domestic these day by quality control of that is profitable and weather condition etc. of coreZone. C.F.R.D is less research about seismic survey(Refractional Seismic Prospectin, Resistivity Prospecting) of levee body than fill dam. Thus as C.F.R.D seismic survey is less, safety of that consist is short most development flue is high reason. That is not checking target of minuteness safety diagnosis and so on by short operation period. Wish to analyze inquiry incidental and difference with center core type dam and acquire C.F.R.D preservation administration upper necessary inquiry condition forward hereafter.
A theoretical equation was proposed to consider the effect of fill and ponding for the excess pore water pressure in agricultural reservoir on soft clay ground. For the purpose of verification of the proposed equation, laboratory model tests and field tests were performed and excess pore water pressure was compared to those predicted with the Terzaghi's method. The degree of consolidation according to ponding predicted by applying the proposed equation was close to the observed degree of consolidation on the double drainage condition(at DP-3) but it was less than the observed degree of consolidation on the single drainage condition(at DP-5). The predicted excess pore water pressure according to fill and ponding was very applicable to practice because it was close to the observed data.
The necessity of a Z-shape heat pipe may occur in a special application such as a cooling module for an electronic equipment having a limited accessible space. Either of the two end part works as evaporator or condenser and the length of the middle part is 200mm. The heat pipe was made of 3/8 inch copper tube having 60 spiral groove with screw angle of 10 degrees. Water and acetone were used as working fluids. The fill charge ratio of the working fluid was varied for different values of thermal loads. The thermal resistance was calculated based on the temperature measurements along the heat pipe axis. The maximum thermal loads were 80W for water and 100W for acetone heat pipe. The optimum fill charge ratio was identified through a series of experiments.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.