• Tunnel and Underground Space
• /
• v.9 no.4
• /
• pp.296-305
• /
• 1999

In ordinary back analysis it if hardly possible to obtain the mechanical properties of tunnel lining by using commonly measured displacements of tunnel lining, because only a few displacements could be measured at the site. Therefore, it is necessary to develop a new method which can evaluate the state of stresses of tunnel by using measured data. In this study, in order to assess tunnel lining stability by estimating its stresses with a few measured displacements, a formulation of back analysis method was proposed. The accuracy of results were investigated through the parametric study for several types of measurement model of two dimensional elastic lining. This new back analysis method to assess tunnel lining stresses and strains with a few numbers of measured displacements showed high accuracy and good applicability when compared to the results of numerical experiments by FEM. The method has been tested on subway tunnel and its applicability has been confirmed by comparing field and analytical data. It is verified that the stress on the tunnel lining can be obtained by only more than 3 point of input displacements without any condition of external loads.

• Radiation Oncology Journal
• /
• v.15 no.1
• /
• pp.71-78
• /
• 1997

Purpose : To collect beam data for dynamic wedge fields using conventional measurement tools without the multi-detector system, such as the linear diode detectors or ionization chambers. Materials and Methods : The accelerator CL 2100 C/D has two photon energies of 6MV and 15MV with dynamic wedge an91es of 15o, 30o, 45o and 60o. Wedge transmission factors, percentage depth doses(PDD's) and dose Profiles were measured. The measurements for wedge transmission factors are performed for field sizes ranging from $4\times4cm^2\;to\;20\times20cm^2$ in 1-2cm steps. Various rectangular field sizes are also measured for each photon energy of 6MV and 15MV, with the combination of each dynamic wedge angle of 15o 30o. 45o and 60o. These factors are compared to the calculated wedge factors using STT(Segmented Treatment Table) value. PDD's are measured with the film and the chamber in water Phantom for fixed square field. Converting parameters for film data to chamber data could be obtained from this procedure. The PDD's for dynamic wedged fields could be obtained from film dosimetry by using the converting parameters without using ionization chamber. Dose profiles are obtained from interpolation and STT weighted superposition of data through selected asymmetric static field measurement using ionization chamber. Results : The measured values of wedge transmission factors show good agreement to the calculated values The wedge factors of rectangular fields for constant V-field were equal to those of square fields The differences between open fields' PDDs and those from dynamic fields are insignificant. Dose profiles from superposition method showed acceptable range of accuracy(maximum 2% error) when we compare to those from film dosimetry. Conclusion : The results from this superposition method showed that commissionning of dynamic wedge could be done with conventional dosimetric tools such as Point detector system and film dosimetry winthin maximum 2% error range of accuracy.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.1
• /
• pp.98-104
• /
• 2018

The assessment of the light trespass in terms of light pollution is difficult due to the complexity of light environments. As a result, the light pollution research has examined the influences of light pollution using simulation program such as RELUX. However, there still exists a differences between the real measurement value and the simulation value for the light trespass. In this paper, we analyzed the light trespass using the RELUX simulation program, and compared results with real measurement values. In this study, the regions (Seoul, Incheon, etc.) were investigated regarding the light trespass for outdoor lighting. The survey of vertical illuminance was analyzed measuring point (more than 2 point) out the window that was expected to light trespass for the higher anticipated to illumination. The illuminational predicted values for the RELUX program were compared with maximum one. As a result of this study, the illuminational errors between the measurement values and predicted values for the simulation were examined from -0.97 lx to 0.65 lx except 2.08 lx and -7.70 lx. The light trespass was analyzed the higher by how much the located close to the height, length, width of the outdoor lighting for the window. For measuring predicted values using RELUX, it was not sufficiently considered in the simulation conditions because of environmental factors and investigator error etc. Limitations of this study include the limited number of measurements, and greater field data is required in future studies.

• Journal of Nutrition and Health
• /
• v.38 no.10
• /
• pp.880-894
• /
• 2005

The purposes of this study were to a) measure the IC identified of CFMC (contract foodservice management company) ,b) examine IC circumstance of CFMC, c) evaluate practically IC measurement tool of CFMC, and d) present information for selecting an adequate CFMC to clients. The questionnaires of IC measurement were handed out to 108 CFMCs, there composing of main office employees, foodservice managers, customers, and clients of 207 school,38 hospital, and 86 husiness/industry foodservices. The statistical data analysis was completed using SPSS Win (ver 12.0) for descriptive analysis, t-test, Mann-Whitney U test. First, CFMCs had operational experience for an average of 8 years and 8 months, and served an average of 38,540 meals a day. Most of the respondent companies specialized in the school foodservice field and managed an average of 66 clients for the contract period of 2 years and 3 months. Second, the respondent companies had gotten a score of 77.78 points for the total average, 77.7 points in the large enterprise group and 78.1 points in the small and medium-sized enterprise group. Therefore, the minimum number of points for the accrediting license on Qualification is suggested to be over 70 out of a 100 point scale; this study would be serve as reference for the certification license on qualification. On the level of evaluation category, the scores were 14.15 to 20 points on $\ulcorner$finance$\urcorner$, 19.24 to 25 points on $\ulcorner$customer$\urcorner$, 19.33 to 25 points on $\ulcorner$process$\urcorner$, 14.31 to 20 points on $\ulcorner$human resource$\urcorner$, and 8.6 to 10 point on $\ulcorner$renewal and development$\urcorner$ . $\ulcorner$Renewal and development$\urcorner$ and $\ulcorner$customer focus$\urcorner$ received better grades than other evaluation categories. Third, $\ulcorner$Finance$\urcorner$ indicated similar distribution overall. Small and medium-sized companies had lower grades than large companies on 'market ability' of $\ulcorner$customer$\urcorner$ , but, clients of small and medium-sized companies had higher grade for 'client satisfaction' than large companies. Most of the companies supported 'infrastructure support for foodservice operation' of $\ulcorner$process$\urcorner$ by the main office of CFMCs, but, the branch chain offices of CFMCs were not applied efficiently. Large companies made more effort to improve the 'employee ability' of $\ulcorner$human focus$\urcorner$ than small and medium-sized CFMC. The 'research and development cost' of $\ulcorner$renewal and development$\urcorner$ was increased compared to the previous year. In conclusion, if CFMCs were to perform self-evaluation and a routine checkups by utilizing CFMC's IC measuring tool, improvements in CFMC operational capacities as well as foodservice quality can be noted. (Korean J Nutrition 38(10)'880$\sim$894,2005)

• Geophysics and Geophysical Exploration
• /
• v.11 no.4
• /
• pp.343-349
• /
• 2008

We have constructed a car-borne magnetic exploration system, in which a car drags a non-magnetic cart on which a magnetometer is installed. In the total magnetic field measured as a vectorial sum in this system, are included the magnetic field generated by the car itself. This magnetic field, doing the role of a magnetic noise, should be eliminated. For this purpose, we have set up a measurement condition to get the same effect as if we have put the car in one point and thereafter measured the magnetic field around it. In this case, if there is any magnetically anomalous body in the area, we can consider all the remaining magnetic field to have been generated by the car itself, once the geomagnetic field eliminated. We tried to invert the magnetic field considered to have been generated by the car and succeeded to derive the magnetic moment and the direction of the induced and remanent magnetic field of the car respectively. Once the magnetic moment and the direction of the induced and remanent magnetic field have been calculated, the magnetic field generated by them in specific points can be directly and analytically calculated. This result can be used in the future to eliminate the magnetic field generated by the car itself doing the role of a magnetic noise during the procedure of reduction of the measured magnetic exploration data by the car-borne magnetic exploration system.

• Journal of Navigation and Port Research
• /
• v.40 no.6
• /
• pp.385-390
• /
• 2016

ELoran Systems can provide Position, Navigation, and Time services with comparable performance to Global Positioning Systems (GPS) as a back up or alternative system. High timing and navigation performance can be achieved by eLoran signals because eLoran receivers use "all-in-view" reception. This incorporates Time of Arrival (TOA) signals from all stations in the service range because each eLoran station is synchronized to Coordinated Universal Time (UTC). Transmission station information and the differential Loran correction data are transmitted via an additional Loran Data Channel (LDC) on the transmitted eLoran signal such that eLoran provides improved Position Navigation and Timing (PNT) over legacy Loran. In this paper, we propose a technique for adapting the delay time compensation values in eLoran timing receivers to provide precise time comparison. For this purpose, we have designed a system that measures time delay from the crossing point of the third cycle extracted from the current transformer at the end point of the transmitter. The receiver delay was measured by connecting an active H-field, an E-field and a passive loop antenna to a commercial eLoran timing receiver. The common-view time transfer technique using the calibrated eLoran timing receiver improved the eLoran transfer time. A eLoran timing receiver calibrated by this method can be utilized in the field for precise time comparison as a GNSS backup.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.22 no.6
• /
• pp.874-880
• /
• 2018

3D modeling is extensively used in the field of architecture, machinery and contents production such as movies. Modeling is a time-consuming task. In order to compensate for these drawbacks, attempts have recently been made to reduce the production period by applying 3D scanning technology. 3D scanning for small objects can be done directly with laser or optics, but large buildings and sculptures require expensive equipment, which makes it difficult to acquire data directly. In this study, 3D modeling data for a large object is acquired using photometry with using drones to acquire the image data. The maintenance method for uniform spacing between the sculpture and the drone, the measurement method for the flight line were presented. In addition, we presented a production environment that can utilize the obtained 3D point cloud data for animation and a rendered animation result to find ways to make it in various environments.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.1334-1337
• /
• 2006

System identification is the field of modeling dynamic systems from experimental data. As a modeling technique, we can mention finite element method (FEM). In addition, we are able to measure modal data as the experimental data. The system can be generally categorized into a gray box and black box. In the gray box, we know mathematical model of a system, but we don't know structural parameters exactly, so we need to estimate structural parameters. In the black box, we don't know a system completely, so we need to identify system from nothing. To date, various system identification methods have been developed. Among them, we introduce system realization theory which uses Hankel matrix and Eigensystem Realization Algorithm (ERA) that enable us to identify modal parameters from noisy measurement data. Although we obtain noise-free data, however, we are likely to face difficulties in identifying a structure with hidden modes. Hidden modes can be occurred when the input or output position comes to a nodal point. If we change a system using a mode decoupling controller, the hidden modes can be revealed. Because we know the perturbation quantities in a closed loop system with the controller, we can realize an original system by subtracting perturbation quantities from the closed loop system. In this paper, we propose a novel method to identify a structure with hidden modes using the mode decoupling controller and the associated example is given for illustration.

• Explosives and Blasting
• /
• v.40 no.4
• /
• pp.15-26
• /
• 2022

With the recent increase in old and dangerous buildings, the demand for technology in the field of structure demolition is rapidly increasing. In particular, in the case of structures with severe deformation of damage, there is a risk of deterioration in stability and disaster due to changes in the load distribution characteristics in the structure, so rapid structure demolition technology that can be efficiently dismantled in a short period of time is drawing attention. However, structural deformation such as unauthorized extension or illegal remodeling occurs frequently in many old structures, which is not reflected in structural information such as building drawings, and acts as an obstacle in the demolition design process. In this study, as an effective way to overcome the discrepancy between the structural information of old structures and the actual structure, access to actual structures through 3D modeling was considered. 3D point cloud data inside and outside the building were obtained through LiDAR and drone photography for buildings scheduled to be blasting demolition, and precision matching between the two spatial data groups was performed using an open-source based spatial information construction system. The 3D structure model was completed by importing point cloud data matched with 3D modeling software to create structural drawings for each layer and forming each member along the structure slab, pillar, beam, and ceiling boundary. In addition, the modeling technique proposed in this study was verified by comparing it with the actual measurement value for selected structure member.

• Proceeding of Spring/Autumn Annual Conference of KHA
• /
• 2009.11a
• /
• pp.23-26
• /
• 2009

The trend that an apartment is regarded as not only a substantial property called 'residence' but also 'means of self-expression' to consumers is increasing in the present housing marketing, and thus, the apartment brand image is settling down as an important field of marketing management. Therefore, the present study aimed to verify difference of brand attitude according to consentaneity between an image of a housing brand and self-image of consumers to propose one kind of direction of strategies for formation of a differentiated brand image. As a result of a research, the trend that consumers show more positive attitude on a brand apartment having a brand image closer to an ideal self-image was analyzed to exist even if it is weak, so it was confirmed that the consentaneity between a brand image and a self-image of housing products can become a variable having some influence on brand attitude. The survey method understood a brand image, a self-image and brand attitude by using a Likert's 5-point scale on apartment brands of upper three companies according to a study result of a national brand competitiveness index(NBCI) and understood self-consentaneity by using a distance measurement model of self-consentaneity of Sirgy(1982). The questionnaire for the present research was carried out by surveying students of D university and the PASW program was used for statistical data analysis.