• Earthquakes and Structures
• /
• v.19 no.3
• /
• pp.157-174
• /
• 2020

The in-situ pushover test differs from the shake-table test because it is performed outdoors and thus its size is not restricted by space, which allows us to test a full-size building. However, to build a new full-size building for the test is not economical, consequently scholars around the world usually make scale structures or full-scale component units to be tested in the laboratory. However, if in-situ pushover tests can be performed on full-size structures, then the seismic behaviors of buildings during earthquakes can be grasped. In view of this, this study conducts two in-situ pushover tests of reinforced concrete (RC) buildings. One is a masonry-infilled RC building with openings (the openings ratio of masonry infill wall is between 24% and 51%) and the other is an RC building without masonry infill. These two in-situ pushover tests adopt obsolescent RC buildings, which will be demolished, to conduct experiment and successfully obtain seismic capacity curves of the buildings. The test results are available for the development or verification of a seismic evaluation model. This paper uses ASCE 41-17 as the main evaluation model and is accompanied by a simplified pushover analysis, which can predict the seismic capacity curves of low-rise buildings in Taiwan. The predicted maximum base shear values for masonry-infilled RC buildings with openings and for RC buildings without masonry infill are, respectively, 69.69% and 87.33% of the test values. The predicted initial stiffness values are 41.04% and 100.49% of the test values, respectively. It can be seen that the ASCE 41-17 evaluation model is reasonable for the RC building without masonry infill walls. In contrast, the analysis result for the masonry infilled RC building with openings is more conservative than the test value because the ASCE 41-17 evaluation model is limited to masonry infill walls with an openings ratio not exceeding 40%. This study suggests using ASCE 41-17's unreinforced masonry wall evaluation model to simulate a masonry infill wall with an openings ratio greater than 40%. After correction, the predicted maximum base shear values of the masonry infilled RC building with openings is 82.60% of the test values and the predicted initial stiffness value is 67.13% of the test value. Therefore, the proposed method in this study can predict the seismic behavior of a masonry infilled RC frame with large openings.

• Journal of Korean Library and Information Science Society
• /
• v.51 no.2
• /
• pp.355-379
• /
• 2020

Digital Library System(DLS) for the school library is a key access tool for school library materials. The purpose of this study was to find ways to improve the accessibility of materials through analysis of students' information search behavior in DLS. Data were collected through recording of 42 participants' DLS search process, and questionnaire. As a result, the search success rate and search satisfaction were found to be lower when the main purpose of DLS is simple leisure reading, information needs are relatively ambiguous, and when user experiences the complicated situations in the search process. The satisfaction level of search time sufficiency was the highest, and the search result satisfaction was the lowest. Besides, there was a need to improve DLS, such as integrated search of other library collection information, the recommendation of related materials, the print output of collection location, voice recognition through mobile apps, and automatic correction of search errors. Through this, the following can be suggested. First, DLS should complement the function of providing career information by reflecting the demand of education consumers. Second, improvements to DLS functionality to the general information retrieval system level must be made. Third, an infrastructure must be established for close cooperation between school library field personnel and DLS management authorities.

• Geophysics and Geophysical Exploration
• /
• v.23 no.3
• /
• pp.168-177
• /
• 2020

Seabed multiple reflections (seabed multiples) are the main cause of misinterpretations of primary reflections in both shot gathers and stack sections. Accordingly, seabed multiples need to be suppressed throughout data processing. Conventional model-driven methods, such as prediction-error deconvolution, Radon filtering, and data-driven methods, such as the surface-related multiple elimination technique, have been used to attenuate multiple reflections. However, the vast majority of processing workflows require time-consuming steps when testing and selecting the processing parameters in addition to computational power and skilled data-processing techniques. To attenuate seabed multiples in seismic reflection data, input gathers with seabed multiples and label gathers without seabed multiples were generated via numerical modeling using the Marmousi2 velocity structure. The training data consisted of normal-moveout-corrected common midpoint gathers fed into a U-Net neural network. The well-trained model was found to effectively attenuate the seabed multiples according to the image similarity between the prediction result and the target data, and demonstrated good applicability to field data.

• Geophysics and Geophysical Exploration
• /
• v.14 no.4
• /
• pp.298-304
• /
• 2011

We conducted magnetic survey using IBRV (Ice Breaker Research Vessel) ARAON of KORDI (Korea Ocean Research and Development Institute), ROV (Remotely Operated Vehicle) of Oceaneering Co. and three components vector magnetometer, at Apr., 2011 in the western slope of the caldera of TA25 seamount, the Lau Basin, the southwestern Pacific. The depth ranges of the survey area are from about 900 m to 1200 m, below sea level. For the deep sea magnetic survey, we made the nation's first small deep sea three components magnetometer of Korea. The magnetometer sensor and the data logger was attached with the upper part and lower part of ROV, respectively. ROV followed the planning tracks at 25 ~ 30 m above seafloor using the altimeter and USBL (Ultra Short Base Line) of ROV. The three components magnetometer measured the X (North), Y (East) and Z (Vertical) vector components of the magnetic field of the survey area. A motion sensor provided us the data of pitch, roll, yaw of ROV for the motion correction of the magnetic data. The data of the magnetometer sensor and the motion sensor were recorded on a notebook through the optical cable of ROV and the network of ARON. The precision positions of magnetic data were merged by the post-processing of USBL data of ROV. The obtained three components magnetic data are entirely utilized by finding possible hydrothermal vents of the survey area.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.9 s.351
• /
• pp.149-157
• /
• 2006

Turbo code, a kind of error correction coding technique, has been used in the field of digital mobile communication system. As the number of iterations increases, it can achieves remarkable BER performance over AWGN channel environment. However, if the number of iterations is increased in the several channel environments, any further iteration results in very little improvement, and requires much delay and computation in proportion to the number of iterations. To solve this problems, it is necessary to device an efficient criterion to stop the iteration process and prevent unnecessary delay and computation. In this paper, it proposes an efficient and simple criterion for stopping the iteration process in turbo decoding. By using variance values of LLR in turbo decoder, the proposed algerian can largely reduce the average number of iterations without BER performance degradation in all SNR regions. As a result of simulation, the average number of iterations in the upper SNR region is reduced by about $34.66%{\sim}41.33%$ compared to method using variance values of extrinsic information. the average number of iterations in the lower SNR region is reduced by about $13.93%{\sim}14.45%$ compared to CE algorithm and about $13.23%{\sim}14.26%$ compared to SDR algorithm.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.3 no.3
• /
• pp.1-7
• /
• 1983

In spite of extensive knowledge of the surface chemistry and the transport mechanism in filtration systems, there is still insufficient understanding of the physical characteristics of suspensions and the system components. Because of this, no filtration mechanisms are mathematically generalized to the full extent. The purpose of this paper is to propose experimental equations for the filtration process. using the tracer study in filter layer. Some of results are as follows. (1) The Volume of the specific deposit (${\sigma}$) in filtration was directly measurable using the tracer study without interrupting the filtration. (2) It was also confirmed that the head loss in filtration was greatly in fluenced by the micro-air babbles. (3) The correction coefficient(f) was introduced into the Kozeny-Carman equation in order to apply it for the clogging filter media. The coefficient(f) was experimentally obtained. The total head loss of the filter media is given by next equation. $${\frac{h}{h_0}}={\frac{1}{L}}{\int}^{z=L}_{z=0}f({\sigma})g({\varepsilon}_0,{\sigma})dz$$ $$f=aexp(-b{\sigma})$$ The above equation was applicable without regard to the variation of the suspension concentration, the filter medium diameter, the filter depth, the filtration velocity, and the amount of aluminum in all continuous filtration experiments. (4) The total head loss was graphically generalized assuming mathematical filtration models I II (see fig. 7,8) (5) The total head loss was obtained from the filtration model in the field filtration conditions. (see fig. 9,10)

• 대한공업교육학회지
• /
• v.36 no.1
• /
• pp.1-22
• /
• 2011

The purpose of this study was to develop and apply activity-centered STEM education program of electricity and electronics technology are in middle schools. The program was developed on the emphasis of problem solving in real world in relation to knowledge, attitude, and skill of Science, Technology, Engineering, and Mathematics. Basically the activity-centered STEM education program was developed through three steps of preparation, development and improvement. In the preparation stage the fellowing was included: (1) need analysis of student, educator, society (2) selection of integration type (3) analyzing subject matter of electricity, electronics area (4) establishing criteria for selecting activity tasks. In the development stage the fellowing was conducted: (1) selection of activity tasks (2) setting up educational goals (3) analyzing activity and clarifing the detailed activity (4) selecting program content, (5) organization of instructional content (6) statement of instructional objectives (7) structuring STEM education program In the improvement stage the fellowing was consisted of: (1) verification of validity by experts (2) execution of pilot test and field test by students and correction of program. The results of the applied the Activity-Based STEM Education Program to 'Afterschool' activities of S middle school were as follow: First, student' satisfaction level was high. Second, student' achievement in the cognitive domain, and affective domain was positive change. Third, student' problem solving ability was positive effect.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.5B
• /
• pp.393-403
• /
• 2011

This study theoretically reviewed the empirical G/R ratio by considering three regression and trend lines; the general linear regression curve, linear regression curve passing the origin, and the line passing the origin and the mass center of observed data. This review included the problem of choosing the independent variable and that of considering the zero measurements. This review result was also applied to the Typhoon Maemi in 2003 for their evaluation. Additionally, those regression and trend lines were compared using the RMSE between the corrected radar rainfall and observed rain gauge rainfall to select the most appropriate G/R ratio. Summarizing the results is as follows. First, the results of selecting the rain gauge rainfall as the independent variable were found better than the opposite case. Second, the effect of zero measurements varies depending on the structure of radar and rain gauge rainfall. Finally, the results from the comparison of three regression and trend lines shows that the slope of the regression line passing the origin with its independent variable of rain gauge rainfall would be used most appropriately for the G/R ratio, especially when the corrected radar rainfall is used for the flood analysis. The effect of zero measurements in this case was found not so significant.

• Radiation Oncology Journal
• /
• v.8 no.1
• /
• pp.115-124
• /
• 1990

The characteristics of 23 MV photon beam have been presented with respect to clinical parameters of central axis depth dose, tissue-maxi mum ratios, scatter-maximum ratios, surface dose and scatter correction factors. The nominal accelerating potential was found to be $18.5\pm0.5$ MV on the central axis. The half-value layer (HVL) of this photon beam was measured with narrow beam geometry from central axis, and it has been showed the thickness of $24.5\;g/cm^2$. The tissue-maximum ratio values have been determined from measured percentage depth dose data. In our experimental dosimetry, the surface dose of maximum showed only $9.6\%$ of maximum dose at $10\times10\;cm^2$, 100 cm SSD, without blocking tray in. The TMR'S of $0\times0$ field size have been determined to get average $2.3\%$ uncertainties from three different methodis; are zero effective attenuation coefficient, non-ilnear least square fit of TMR's data and effective linear attenuation coefficient from the HVL of 23 MV photon beams of dual energy linear accelerator.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.26 no.3
• /
• pp.241-253
• /
• 2008

Recently, it is appearing that new paradigm of urban planning that ubiquitous concept such as the u-City, uECO-City is introduced while is rising necessity about third dimensional geo-spatial information of high quality for urban area. Orthophoto can manufacture by expense and time that is less easily than digital map using personal computer even if is not highly technician and according as position relation between manmade feature and natural feature is equal, can get information of distance, angle, horizontal and vertical position coordinate of topographic, area etc.. directly through orthophoto. Also, visual effect is good that orthophoto is expressed by image and interpretation is easy to detailed part of topographic. Manufacture and practical use are consisting in various field, for it is having advantage that can recognize information effectively than digital map. Therefore, this study presents a way of generating a detailed DSM for producing a true-orthphoto of the urban area, and this study also presents a way to produce an optimum true-orthophoto for an urban area by investigating through experiment the optimum variable for the geometric and radiometric correction of the orthophoto. This study also examined the potentials of the thesis by building a 3-dimensional city model of the model region with the above thesis on optimum generating method.