• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2004년도 춘계 학술발표회 제16권1호
• /
• pp.308-311
• /
• 2004

Many researchers have reported that adding steel fiber to concrete improved its tensile and flexural strength significantly, but relatively few studies have been made on the compressive behavior of SFRC(steel fiber reinforced concrete). It is still less in case of high strength SFRC. The main objective of this research is to examine the effect of adding steel fiber on the compressive strength of high strength SFRC using fiber reinforcing index$(RI,\;V_f(l/d))$. It was found from the study that compressive strength was noticeably increased in proportion to RI.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2004년도 춘계 학술발표회 제16권1호
• /
• pp.288-291
• /
• 2004

In this paper, to make ultra-high strength SFRCC with the range of compressive strength 180MPa, it was investigated the constitute factors of ultra-high strength SFRCC influenced on the compressive strength. The experimental variables were water-cementitious ratio, replacement of silica fume, size and proportion of sand, type and replacement of filling powder, and using of steel fiber in ultra-high strength SFRCC. As a result, in water-binder ratio 0.18, we could make ultra-high strength SFRCC with compressive strength 180MPa through using of silica fume, quartz sand with below 0.5mm, filling powder and steel fiber.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2005년도 추계 학술발표회 제17권2호
• /
• pp.29-32
• /
• 2005

An experimental investigation on the strength and behavior of High Performance Fiber Reinforced Cement Composite(HPFRCC) column with Polyvinyl alcohol(PVA) fibers under axial load have been carried out. The columns were subjected to monotonic axial compression until failure. The variables in this study are the combination ratio of PVA, and the volumetric ratio of transverse reinforcement. Test results showed that the fibers, when used in PVA2.0, could result in superior composite performance compared to their individual fiber reinforced cement composites.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2004년도 춘계 학술발표회 제16권1호
• /
• pp.734-737
• /
• 2004

The synthetic fibers such as polypropylene(PP) and polyvilyl-alcohol(PVA) fiber are poised as a low cost alternative for reinforcement in structural applications. It has been reported that synthetic fiber in cement composites can control restrained tensile stresses and cracks and increase toughness, resistance to impact, corrosion, fatigue and durability. High performance fiber reinforced cementitious composite(HPFRCCs) shows ultra high ductile behavior in the hardened state, because of the fiber bridging properties. Therefore, a variety of experiments have being performed to access the performance of HPFRCCs recently. The research emphasis is on the flexural behavior of HPFRCCs made in synthetic fibers, and how this affects the composite property, and ultimately its strain-hardening performance. Three-point bending tests on HPFECCs are carried out. As the result of the bending tests, HPFRCCs showed high flexural strength and ductility. HPFRCCs made in PVA or Hybrid fiber were, also, superior to PP of singleness. On the other hand, effect of sand volume fraction on HPFRCCs made in PP was insignificant.

• Structural Engineering and Mechanics
• /
• 제89권4호
• /
• pp.349-362
• /
• 2024

High-performance fiber-reinforced cement composites (HPFRCC) are new materials created and used to repair, strengthen, and improve the performance of different structural parts. When exposed to tensile tension, these materials show acceptable strain-hardening. All of the countries of the globe currently seem to have a need for these building materials. This study aims to create a low-carbon HPFRCC (high ductility) that is made from materials that are readily available locally which has the right mechanical qualities, especially an increase in tensile strain capacity and environmental compatibility. In order to do this, the effects of fiber volume percent (0%, 0.5%, 1%, and 2%), and determining the appropriate level, filler type (limestone powder and silica sand), cement type (ordinary Portland cement, and limestone calcined clay cement or LC3), matrix hardness, and fiber type (ordinary and oxygen plasma treated polypropylene fiber) were explored. Fibers were subjected to oxygen plasma treatment at several powers and periods (50 W and 200 W, 30, 120, and 300 seconds). The influence of the above listed factors on the samples' three-point bending and direct tensile strength test results has been examined. The results showed that replacing ordinary Portland cement (OPC) with limestone calcined clay cement (LC3) in mixtures reduces the compressive strength, and increases the tensile strain capacity of the samples. Furthermore, using oxygen plasma treatment method (power 200 W and time 300 seconds) enhances the bonding of fibers with the matrix surface; thus, the tensile strain capacity of samples increased on average up to 70%.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 추계 학술발표회 논문집
• /
• pp.657-660
• /
• 2006

HPFRCCs(High performance fiber reinforced cementitious composites) exhibit characteristics of strain harding and multiple crack. These lead to improvement in ductility, toughness, and deformation capacity under compressive and tensile stress. These properties of HPFRCCs are affected by type of fiber, size of sand. Furthermore these influence compress strength and flexural strength. Therefore experimental study on the mechanical properties of HPFRCCs using PVA fiber was carried out. In this paper, HPFRCCs made of PVA fiber were tested with size of sand, strength of concrete to evaluate characteristics of compressive strength and flexural strength.

• 콘크리트학회논문집
• /
• 제17권5호
• /
• pp.709-716
• /
• 2005

이 연구는 국내에서 상용 중인 재료를 이용하여 고인성 섬유복합 모르타르를 개발하고자 함에 목적이 있으며, 고인성 섬유복합 모르타르를 개발하기 위해서는 모르타르 매트릭스의 파괴역학(fracture mechanics)적 특성과 섬유-모르타르 경계 면의 마이크로역학(micromechanics)적 특성을 파악하여야 한다. 특히 시멘트계 재료(cementitious materials)의 역학적 특성에 가장 큰 영향을 미치는 물-시멘트비(water cement ratio)에 대한 연구에 초점을 맞추었으며, 3가지의 물-시멘트비에 대하여 섬유의 인발실험(fiber pullout test)과 모르타르의 쐐기쪼갬실험(wedge splitting test)을 수행하였고 이를 통하여 모르타르 매트릭스와 섬유-매트릭스 경계면(interface)의 역학적인 특성을 파악하였다. 이러한 연구에 의하여 결정된 섬유-매트릭스 경계면의 마이크로역학적 특성과 모르타르의 역학적 특성을 이용하여 물-시멘트비 범위 및 재료의 기본 배합을 제시하였고 또한 마이크로역학과 안정상태 균열이론(steady-state cracking theory)을 배경으로 하여 1축인장 하에서 인장변형률 경화거동을 나타내는 고인성 섬유복합 모르타르를 개발하였다. 개발된 재료는 1축인장 하에서 변형률 경화거동을 나타내었으며, 변형능력은 최대 2.2% 이었다. 이와 같은 높은 변형 능력은 일반 콘크리트(또는 모르타르)의 약 100배에 해당된다. 또한 압축하에서는 압축강도 이후 응력-변형률 곡선이 완만하게 감소하는 연성파괴의 형태를 나타내었으며 28일의 압축강도는 보통강도 콘크리트의 강도에 해당되는 26MPa, 34MPa인 것으로 측정되었다.

• Advances in Computational Design
• /
• 제8권2호
• /
• pp.113-131
• /
• 2023

The use of fibers has been commonly considered in engineered cementitious composites, but their behavior with coarse aggregate in concrete has not been studied significantly, which is needed to meet structural performance objectives for design, such as ductility. This research analyzes the behavior of fiber-reinforced concrete with coarse aggregate with 0.62%, 1.23%, and 2% PVA (Polyvinyl-alcohol) content, varying the maximum aggregate size. Tensile (direct and indirect) and compressive concrete tests were performed. The PVA fiber addition in coarse aggregate concrete increased the ductility in compression, especially for the fiber with a larger aspect ratio, with a minor impact on strength. In addition, the tensile tests showed that the PVA fiber increased the tensile strength of concrete with coarse aggregate and, more significantly, improved the ductility. A selected mixture was used to build short and slender reinforced concrete beams to assess the behavior of structural members. PVA fiber addition in short beams changed the failure mode from shear to flexure, increasing the deflection capacity. On the other hand, the slender beam tests revealed negligible impact with the use of PVA.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2016년도 춘계 학술논문 발표대회
• /
• pp.30-31
• /
• 2016

As the treatments of many kinds of explosive objects increase recently, it is in the trend that explosion accidents increase. Thus, many studies on HPFRCC (High-performance Fiber-reinforced Cement Composites) whose ductility is enhanced are being conducted actively in order to minimize the damages from explosion accidents. However, HPFRCC, the self-shrinkage of HPFRCC is on the rise as a problem since it becomes ultra-high strengthened by using low W/B. Thus, in this study, it is intended to evaluate the capacity for reducing the self-shrinkage of HPFRCC depending on some changes of ERCO(Emulsified Refined Cooking Oil) replacement ratio and the fiber replacement ratio between some short steel fibers (SS) and some long organic fibers (OL). As a result, it was found that some excellent effects are exerted since the self-shrinkage was reduced a lot as the ERCO replacement ratio increases and the fiber replacement ratio of SS rather than OL increases.

• Composites Research
• /
• 제12권3호
• /
• pp.84-90
• /
• 1999

HAC/PVA계 MDF시멘트 복합재료의 수분안정성 및 기계적 강도향상을 위하여 불용성 폴리머류(폴리우레탄, 페놀, 에폭시수지)와 탄소섬유(길이3mm)를 1-4wt% 보강하였다. 그리고 가압성형법으로 제조한 복합체의 수분침적 기간별 강도특성(수분안정성)과 계면 및 기계적 특성에 영향을 미치는 폴리머와 시멘트의 가교반응에 대하여 SEM 및 TEM 분석을 통하여 관찰하였다. HAC/PVA계 MDF 시멘트 복합체의 섬유함량에 따른 건조 굽힘강도는 섬유함량이 증가할수록 치밀화 구조가 저하되어 비례적으로 감소되었다. 또한 불용성 폴리머류를 사용한 경우에 건조 굽힘강도는 섬유함량이 증가될수록 저하되는 반면, 수분안정성은 크게 향상되었다. 에폭시 수지를 첨가한 경우에 수분안정성이 가장 우수하였으며, 섬유함량 4% 첨가의 경우에 3일 침적강도가 95%, 7일침적시 87%강도를 유지하였다. 이 점은 폴리머와 시멘트의 금속이온이 가교반응을 일으켜 섬유-메트릭스간 계면 부착강도를 크게 개선되었기 때문으로 추정된다. 반면 인장강도 특성은 모든 불용성 폴리머류 첨가 수준에서 섬유 함량이 증가할수록 비례적으로 증가되었으며, 역시 에폭시 수지 첨가의 경우에 강도특성이 가장 우수하였다. 그리고 섬유함량 4% 첨가된 경우에 있어서 인장강도는 섬유함량 0% 대비 약 30~80% 높게 나타났다.