• 펄프종이기술
• /
• 제34권4호
• /
• pp.1-6
• /
• 2002

In order to simulate the actual wet-end process in papermachine, RDA, a novel handsheet former, was used and following results were obtained. While the addition of polyelectrolytes gives significant effect on fiber flocculation, increase of stock consistency influenced on the formation of RDA sheets greatly. In particular, the consistency increase from 0.3 % to 0.4% abruptly increased floe size of RDA sheet and it results in severe deterioration of paper strength. Stock consistency, therefore, should be regarded as the most important factor in the formation simulation with RDA and should be controlled as the first sequence of tuning the operating conditions of RDA to simulate correctly the target machine paper's formation.

• 한국산학기술학회논문지
• /
• 제11권10호
• /
• pp.4024-4030
• /
• 2010

본 연구에서는 FRP 보강된 각형 CFT기둥의 중심축하중 실험과 이력거동실험을 수행하였다. 실험변수는 중심축하중 실험에서는 폭-두께비, FRP보강겹수이며, 이력실험에서는 콘크리트 강도와 FRP 보강겹수이다. 실험체의 내력과 연성능력을 정리하였고, FRP로 보강된 각형 CFT기둥의 압축내력 설계식을 제안한다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2001년도 가을 학술발표회 논문집
• /
• pp.751-756
• /
• 2001

This paper deals with the experimental evaluation of the performance of R.C beams strengthened with aramid, glass and carbon fiber sheets. To evaluate the effects of FRPs on the flexural strengthening of the beams, strengthening ratio is adopted as a main variable. Seven beams were fabricated and strengthened under same tensile strength based on ultimate strength of FRPs and strengthening length. Deflection, flexural stiffness, strain of FRP, ultimate load and failure load are compared to evaluate the effects of FRPs on structural behavior of retrofitted beams. The results shows that little effects of FRPs on behavior of strengthened beams can be estimated and the fail modes are more influenced on structural behavior than that.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2001년도 가을 학술발표회 논문집
• /
• pp.1003-1008
• /
• 2001

It is recently reported that bond failure can be initiated in the region where maximum bending moment and shear force is acted by accompanying shear deformation after flexural crack in full-scale RC beams strengthened by CFRP. Such a shear deformation effect causing bond failure is relatively little in the case of small-scale specimens. So, additional reinforcing details to the critical beam section where maximum moment and shear were acted is required to prevent the bond failure caused by the shear deformations. The U-type wrapping methods by CFRP to the critical beam section is proposed and tested in this paper. Also, the applicability of design bond strength derived from the tests of small-scale beam was investigated by the full-scale RC beam strengthened by CFRP.

• 펄프종이기술
• /
• 제48권2호
• /
• pp.83-90
• /
• 2016

Increasing the amount of filler in paper is of high interest for paper industry while maintaining its key sheet quality properties. In this study, a MFC-GCC composite, made through a co-grinding NBSK (Northern bleached softwood kraft) pulp with a ground calcium carbonate (Intracarb 60), was used as a strength aid in paper in order to evaluate a potential cost reduction through filler increase without sacrificing paper quality. Hand-sheets were made of NBSK and/or eucalyptus pulp by using white water recirculation in a Tappi sheet former and was compared its properties without or with MFC additions at different filler levels. It was found that the MFC-GCC composite has a large surface area compared to the fiber, allowing the formation of more hydrogen bonds in the web, thus giving natural strength to the paper. Overall results are encouraging that the MFC-GCC composite allows papermaker to reduce basis weight and maintain critical sheet properties.

• Structural Engineering and Mechanics
• /
• 제52권6호
• /
• pp.1209-1224
• /
• 2014

In Current paper, the voltages of patches optimization are carried out for minimizing the power consumption of piezoelectric patches and maximum vertical displacement of symmetrically FML panels using the modified multi-objective Elitist-Artificial Bee Colony (E-ABC) algorithm. The voltages of patches, panel length/width ratios, ply angles, thickness of metal sheets and edge conditions are chosen as design variables. The classical laminated plate theory (CLPT) is considered to model the transient response of the panel, and numerical results are obtained by the finite element method. The performance of the E-ABC is also compared with the PSO algorithm and shows the good efficiency of the E-ABC algorithm. To check the validity, the transient responses of isotropic and orthotropic panels are compared with those available in the literature and show a good agreement.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1996년도 가을 학술발표회 논문집
• /
• pp.221-229
• /
• 1996

An analytical method based on the nonlinear layered finite element method is used to simulate the load-deflection behavior of strengthened beam. Beams considered in this study are the ones strengthened either with external steel plate or Carbon Fiber Reinforced Plastic (CFRP) sheets bonded to the overlay soffit or with reinforcing rebars in the overlay. The theoretically obtained load-deflections and strains of the strengthened beam are compared to the corresponding experimental values. Comparing the approximate measures on the cumulative slips, efficiencies of the repairing techniques are evaluated. Parametric studies are, then, peformed using the developed model to investigate the effects of design variables on the overal flexural behavior of the strengthened beam. Simply supported beams under monotonically increasing symmetrical loads are considered exclusively.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 춘계학술발표회 논문집(I)
• /
• pp.326-329
• /
• 2006

Strengthening method using CFS have been developed for the rehabilitation of structures. However, it is very difficult to estimate their resistance capacity after retrofit. Therefore, damage information for strengthened structure with CFS investigated and the estimation method structural capacity by using the damage information is developed. The final objective of this research work is to propose the guideline and method for resistance capacity estimate of structure. In this paper, experimental study result with test parameters of number of carbon fiber sheets and bonding ratio is introduced.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 춘계학술발표회 논문집(I)
• /
• pp.106-109
• /
• 2006

It has been shown that many reinforced concrete(RC) structures designed without seismic details have experienced brittle shear failures in the beam-column joint area and may result in large permanent deformations and structural collapse. In this study, experimental investigations for RC beam-column joints strengthened with the carbon fiber-reinforced polymer(CFRP) under cyclic loadings were presented. The use of CFRP in the joint was varied to determine the effective way of improving the structural performances of RC joints. Ten RC beam-column joints were designed and tested with cyclic loadings. The experimental results showed that the use of CFRP in RC joints would be very effective solutions to improve the seismic performances of the non-seismic RC joints. All of the non-seismic design specimens strengthened with CFRP sheets showed the significant increase of strength and ductility.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 춘계학술발표회 논문집(I)
• /
• pp.234-237
• /
• 2006

A series of three shear wall specimens was tested under constant axial stress and reversed cyclic lateral loading in order to evaluate the seismic retrofit that had been proposed for the shear wall with the opening induced by remodeling. One of these specimens was tested in the as-built condition and the other two were retrofitted prior to testing. The retrofit involved the use of carbon fiber sheets and steel plates (thickness of 3mm) over the entire face of the wall. The test results show that the ultimate failure modes of the specimens were found to be shear fracture of the wall around the opening and two difference types of retrofitting strategy make the different effects of a rise in the strength of each specimen.