• 펄프종이기술
• /
• 제38권4호
• /
• pp.68-75
• /
• 2006

Electromagnetic shielding sheet using the carbon and wood fiber mixture was manufactured in an effort to develop an electromagnetic shielding packaging material. Carbon fibers were cut into 5, 10, and 15 mm using the automatic cutting device and blown and dispersed using compression air passed through the fine nozzle. Then carbon fibers were slurried with water (0.1% consistency), and softwood kraft pulp along with cone starch were added. The wet mats were manufactured by dewatering in modified hand-sheet machine. The wet mats were pressed upto $4kgf/cm^2$ in the carbon and wood fiber mixture mat press. The wet mats were dried in the automatic controlled plate dryer. Investigation on the formation and surface structure of the newly developed carbon and wood fiber mixture electromagnetic shielding sheet were carried out using the scanning electron microscopy and the image analyzer. Finally electromagnetic shielding characteristics of the newly developed carbon and wood mixture sheet were measured using net-work analyser. The result was promising in the light of the fact that this method could open a new way to substitute the expensive imported electromagnetic shielding sheet.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2007년도 제34회 KOSCO SYMPOSIUM 논문집
• /
• pp.176-183
• /
• 2007

An experimental study was performed to investigate the effects of mixing quality, inlet pressure, nozzle diameter on CO emission and radiation characteristics in porous ceramic fiber radiant burners. Observations of combustion characteristics occurring inside the burner system which was insulated fiber mat, were investigated by measuring temperature, CO emission and radiation characteristics. Combustion was achieved at the firing rate of $88{\sim}99$ kcal/hr, inlet pressure of $100{\sim}250$mm$H_2O$. CO emissions were found to be strongly dependent on the operating conditions. There was a tendency that CO concentration increased as the firing rate increases. The reason for rise of CO concentration is that it becomes the relatively rich condition. The fiber burner exhibit significant both spectral intensity peaks in the bands at 2.5${\mu}m$ and 4.0${\mu}m$ relatively, There is a small difference in the variable mixing tube. However spectral intensity increased with the firing rate.

• 대한기계학회논문집A
• /
• 제20권11호
• /
• pp.3433-3440
• /
• 1996

This paper was investigation of the stres corrosion cracking(SCC) mechanism and the properties of corrosion fracture surface of glass fiber reinforced plastics(GFRP) produced by hand lay up(HLU) method in synthetic sea water. Test material is GFRP, that was used vinylester type epoxy acrylate resin and an unsaturated polyester as the matrix and the chopped strand mat(CSM) type E-glss fiber as the reinforcement. The slow strain rate test(SSRT) was performed on dry, wet and saturated wet specimens in sea water. Here the pH concentration of synthetic sea water was 8.2 and the strain rate is 1 x $10^{-6}$($sec^{-1}$) and test temperature ranges varied from $-60^{\circ}C$ to $80^{\circ}C$. It could be confirmed the fact that wet specimens tested at a particular test temperature ranges were appeared the eviences of SCC such as con-planar, mirror and hackle zone. Moreover, SCC of GFRP in sea water was characterised by falt fracture surfaces with only small amounts of fiber pull-out, in partial.

• 한국식품조리과학회지
• /
• 제8권3호
• /
• pp.333-341
• /
• 1992

The physicochemical, rheological and sensory characteristics of 'BACKSULGIES', which was added with potato peel, guar gum or polydextrose, were investigated. The maximum acceptable addition ratio of dietary fiber to 'BACKSULGI' was 10%. And optimal addition ratio was 3% for all samples. The water binding capacity was affected by dietary fiber sources and incubation conditions (temperature and time). The Guar gum had me highest value of water binding capacity. The solubility was highly related with water binding capacity and me swelling power was increased with temperature increment. The degree of gelatinization was not significantly different with dietary fiber sources. But me values of gelatinization of 'BACKSULGIES' added with dietary fibers were significantly higher than mose of 'BACKSULGI' with no dietary fiber. Generally hardness and brittleness incresed along with storage time. But me hardness of 'BACKSULGIES' added with dietary fibers was significantly lower man those of 'BACKSULGI' with no dietary fiber. The retardation effect of dietary fibers for retrogradation of 'BACKSULGIES' was also proved by time constant determination of Avrami equation. Sernsory evaluation revealed that me addition of dietary fibers did not reduce the organoreptic quality. Therefore potato peel 3%, guar gum 3%, polydextrose 3% were optimum addition ratio which could be accepted as conventional 'BACKSULGI'. As me results of this study, it was proved mat the additions of dietary fibers to 'BACKSULGI' had the retardation effect of retrogradation.

• Composites Research
• /
• 제35권2호
• /
• pp.75-79
• /
• 2022

본 연구에서는 충격에 의해 파손된 열가소성 유리 섬유 강화 복합재료의 재성형을 통한 물성변화를 조사하였다. 복합재료 시편은 유리섬유 부직포와 폴리프로필렌 필름을 이용하여 핫 프레스 압축 성형 공정을 통해 제작하였다. 총 3번의 낙하 충격 테스트를 진행하였으며, 시편의 물성을 확인하기 위하여 인장시험, 굽힘시험, 낙하충격시험, 시차주사열량계, 주사전자현미경 측정을 진행하였다. 그 결과, 재활용 단계가 반복될수록 결정화도, 인장강도, 탄성계수, 굴곡강도는 증가하였으나 충격특성은 크게 감소하였다.

• Computers and Concrete
• /
• 제11권2호
• /
• pp.105-121
• /
• 2013

This paper investigates the parameters that control the design of Fiber Reinforced Polymer (FRP) reinforced concrete flexural members proportioned following the ACI 440.1R-06. It investigates the critical parameters that control the flexural design, such as the deflection limits, crack limits, flexural capacity, concrete compressive strength, beam span and cross section, and bar diameter, at various Mean-Ambient Temperatures (MAT). The results of this research suggest that the deflection and cracking requirements are the two most controlling limits for FRP reinforced concrete flexural members.

• 한국에너지공학회:학술대회논문집
• /
• 한국에너지공학회 1998년도 추계 학술발표회 논문집
• /
• pp.174-179
• /
• 1998

본 연구는 섬유 코팅 건조기에서 사용하고 있는 열풍 건조방식을 촉매버너를 이용한 직접 건조 방식으로 대체하기 위한 것이다. 촉매버너는 파이버 매트를 사용한 확산식 연소 방식을 채택하였다. 확산식 촉매버너는 코팅 건조기와 같은 밀폐형 구조에는 적합하지 않아서 개선이 필요한 것으로 나타났다. 연소용 공기를 촉매버너의 표면에 강제적으로 공급하여 촉매버너의 연소효율을 개선하였다. 아크릴이 코팅된 섬유의 건조 과정에서 발생하는 톨루엔을 회수하여 촉매버너의 연료로 재사용하도록 하였다. 이를 위하여 톨루엔을 사용한 경우의 촉매버너의 최적 설계조건을 도출하였다.

• 폴리머
• /
• 제26권3호
• /
• pp.360-366
• /
• 2002

N,N-dimethyl formamide (DMF) 용매에 용해시킨 폴리아크릴로니트릴 용액을 사용하여 전기방사를 통하여 나노섬유를 제조하였다. 전기방사의 공정인자인 집속롤러 속도, 방사거리, 전압이 나노섬유 직경에 미치는 영향을 알아보았다. 방사거리가 5 cm인 경우에는 섬유 표면에서 DMF 용매가 모두 증발되지 못하여 섬유끼리 뭉치는 현상이 발생하여 평균 섬유 직경이 전압이 증가함에 따라 증가하였다. 그러나 방사거리가 9 cm에서는 DMF 용매가 완전히 증발하여 전압이 증가함에 따라 평균 섬유 직경은 감소하였다. 또한 집속롤러 속도가 증가함에 따라 섬유 직경은 감소하였고 가로방향의 부직포 폭은 전압이 감소함에 따라 그리고 방사거리가 증가함에 따라 증가하였다.

• 폴리머
• /
• 제38권3호
• /
• pp.338-350
• /
• 2014

Cellulose acetate (CA) fiber mats containing inclusion complexes of asiaticoside (AC) in 2-hydroxypropyl-${\beta}$-cyclodextrin ($HP{\beta}CD$) for potential usage as wound dressings were developed. The AC/$HP{\beta}CD$ complex-loaded CA fibers at various $HP{\beta}CD$ to AC molar ratios of 0.5, 1, and 2 were prepared in 90:10 v/v mixture of 80% (v/v) acetic acid and N,N-dimethylacetamide (DMAc) via electrospinning. The maximum released amounts of AC depended on the $HP{\beta}CD$ content and were much greater than those released from the AC-loaded CA fiber mat. In the in vitro study, indirect cytotoxic evaluation with human dermal fibroblasts (HDFa) showed that these materials released no substances in the levels that were harmful to the cells and the cells appeared to attach and proliferate well on these substrates. However, only the CA fiber mats containing AC/$HP{\beta}CD$ complexes at the $HP{\beta}CD$ to AC molar ratio of 0.5 was effective in upregulating the production of collagen of the cultured cells.

• 유변학
• /
• 제10권4호
• /
• pp.185-194
• /
• 1998

수지이동 성형공정에서 섬유직조가 수지에 의해 함침될 때 발생하는 기공 또는 나쁜 젖음성은 최종 성형품의 물성 저하에 심각한 영향을 미치게 된다. 본 연구에서는 함침공정에서의 수지 유동특성을 파악하고 기공 형성기구를 규명하기 위하여, 빔 형태의 금형을 대상으로 실리콘 오일과 평직형태의 유리섬유를 사용하여 미시적인 유동가시화 실험을 수행하였다. 시간과 압력에 따른 수지의 침투길이를 측정함으로써 섬유직조의 기공률에 따른 비정상상태의 투과계수와 모세관압을 측정하였고, 낮은 조업압력과 낮은 기공률에서는 모세관압이 함침공정에서 중요한 가공변수임을 확인할 수 있었다. 비디오 카메라를 이용하여 유동전단면의 이동을 근접 확대 촬영하여 기공이 형성되는 과정을 미시적으로 관찰함으로써, 섬유와 수지의 표면에너지에 의해 발생되는 모세관압이 기공의 형성에 미치는 영향을 조사하였다. 그 결과, 수지충전을 유발하는 전체 구동압력에서 모세관압이 상대적으로 클수록 기공은 더욱 쉽게 생성되는 것으로 나타났다. 또한 수지의 점도와 섬유직조의 기공률이 각각 변화할 때, 모세관수에 따른 기공의 함량을 화상 해석 기법(image analysis technique)을 사용하여 정량적으로 측정하였다. 수지가 섬유직조 내로 함침될 때 임계모세관수(Ca~2.75$\times$$10^{-3})이상에서는 기공이 형성되지 않았으며, 그 이하에서는 모세관수가 감소함에 따라 기공의 함량이 지수적으로 증가하였다. 생성된 기공의 함량은 점도에 관계없이 유사한 변화 경향을 보였으며, 모세관수가 동일한 조건에서는, 기공률이 감소함에 따라 기공의 함량이 감소하였다.