• Composites Research
• /
• v.22 no.4
• /
• pp.33-40
• /
• 2009

Fiber orientation effects on the impact surface fracture of the glass plates coated with the glass fiber/epoxy lamina layer were investigated using a small-diameter steel-ball impact experiment. Four kinds of materials were used: soda-lime glass plates, unidirectional glass fiber/epoxy layer(one ply, two plies)-coated, crossed glass tiber/epoxy layer (two plies)-coated glass plates. The maximum stress and absorbed fracture energy were measured on the back surface of glass plates during the impact. With increasing impact velocity, various surface cracks such as ring, cone, radial and lateral cracks appeared near the impacted site of glass plates. Cracks in the plate drastically diminished by glass fiber coating. The tiber orientation guided the directions of delamination and plastic deformation zones between the tiber layer and the glass plate. Impact surface-fracture indices expressed in terms of the maximum stress and absorbed energy could be used as an effective evaluation parameter of the surface resistance.

• Journal of the Korean Ceramic Society
• /
• v.45 no.4
• /
• pp.238-244
• /
• 2008

Modeling and FEM analysis on Boron Nitride and/or Pyrolytic Carbon coating layers on SiC fibers under indentation contact loadings are investigated. Especially this study attempts to model the mechanical behavior of the SiC fibers with and without coatings. Tyranno S grade and Tyranno LoxM grade of SiC are selected for fiber and Boron Nitride and/or Pyrolytic Carbon as coating material. The modeling is performed by SiC fiber without coating layer, which includs single(BN or PyC) and double(BN-PyC or PyC-BN) coating layer. And then the analysis is performed by changing a type of coating layer, a type of fiber and coating sequence. In this study, the concepts of modeling and analysis techniques for optimum design of BN and PyC coating process on SiC fiber are shown. Results show that stresses are reduced when indentation contact loading applies on the material having lower elastic modulus.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.2 s.233
• /
• pp.220-227
• /
• 2005

In this study, stress-displacement analytic solutions are obtained by a shear lag modeling method constructed for the spliced joint area with a splicing gap in the fiber metal laminate (FML). This gap can be empty or be filled with an adhesive material of elastic modulus $E_a$. Two splicing types are considered for spliced shear models, one for spliced in the center metal layer, the other for spliced in the outer metal layer. It is shown that from the viewpoint of the load transfer efficiency and the avoidability of disbond generation due to the shear and axial stresses at the interface between metal layer and composite layer of the gap-front in the spliced area, the center spliced type (k=2) is much preferable to the outer spliced type (k=1).

• Korean Journal of Optics and Photonics
• /
• v.14 no.4
• /
• pp.355-358
• /
• 2003

We report experimental results on the wavelength and polarization selective coupling properties of fiber-to-planar waveguide coupler having a thin metal intermediate layer. The influence of the metal layer thickness and the refractive index of the superstrate on the device properties has been measured and explained. The proposed device exhibited various application possibilities including polarizers, modulators, and sensors.

• The Korean Journal of Ceramics
• /
• v.1 no.3
• /
• pp.160-164
• /
• 1995

Mechanical and chemical tests were performed on $Zro_2 \cdot SiO_2$ glass fibers manufactured by the sol-gel method and E-glass fibers-reinforced cement composites in order to investigate the interactions between glass fibers and cement matrices. Chemical attack leads to corrosion of the glass fiber surfaces. In the corrosion reactions, the surface of $30ZrO_2 \cdot 70 SiO_2$ glass fibers developed a densified concentric layer, which consists of glass corrosion products with much higher Zr and lower Si than the fresh glass fiber. The layer of reaction product is regarded to stiffen the cement matrices and provide a useful improvement to the mechanical properties. The addition of $ZrO_2$ content increases the corrosion resistance of glass fibers in cement by forming a passivating layer on the surface of glass fibers.

• Carbon letters
• /
• v.26
• /
• pp.102-106
• /
• 2018

• Earthquakes and Structures
• /
• v.10 no.1
• /
• pp.91-104
• /
• 2016

In this paper we investigate the existence of SH-waves in fiber-reinforced layer placed over a heterogeneous elastic half-space. The heterogeneity of the elastic half-space is caused by the exponential variations of density and rigidity. As a special case when both the layers are homogeneous, our derived equation is in agreement with the general equation of Love wave. Numerically, it is observed that the velocity of SH-waves decreases with the increase of heterogeneity and reinforced parameters. The dimensionless phase velocity of SH-waves increases with the decreases of dimensionless wave number and shown through figures.

• Composites Research
• /
• v.24 no.6
• /
• pp.31-36
• /
• 2011

According to the evaluation on GMT-sheet by molding conditions, fiber projection on the moldings surface was investigated. Fiber projection is one of the major defects on moldings surface due to matrix shrinkage. That is, fiber projection happens from different shrinkage of matrix and glass fiber. Height of fiber projection from moldings surface becomes smaller when molding pressure is higher during holding pressure and cooling process. Height of fiber projection is dominantly affected by molding pressure. With consideration of molding pressure, the formation of surface unevenness and change in fiber projection height was elucidated. In addition, coating layer is effective to suppress surface defects, and there is no fiber projection or crack in case that coating is applied. Coating layer improves surface roughness up to the level of the polypropylene which is a single material.

• Macromolecular Research
• /
• v.14 no.5
• /
• pp.499-503
• /
• 2006

This report presents a new technical approach for evaluating the fiber orientation of composites using small-angle light scattering (SALS). Glass fiber (GF)/polypropylene (PP) composites with different fiber orientations were prepared by drawing compression-molded specimens. The drawn samples were remelted and then annealed at $150^{\circ}C$ in order to induce a crystalline structure on the fiber surface, and then underwent SALS analysis. The samples showed a combination of circular and streak patterns. The model calculations demonstrated that the number of nuclei on the fiber surface and the thickness of the transcrystalline layer affected the sharpness and intensity of the streak pattern. In addition, the azimuthal angle of the streak pattern was found to be dependent on the direction of the transcrystalline layer, which correlated with the fiber direction. This correlation suggests that the fiber orientation in the composites can be easily evaluated using SALS.

• Composites Research
• /
• v.27 no.3
• /
• pp.109-114
• /
• 2014

Manufacture of nancomposites has simple process for developing nanocomposites due to the increasing applications using nanofillers. This work studied nanofiller coated glass fiber for reinforcing material with good wetting and conductivity and the morphology of nanofiller coated glass fiber was analyzed by FE-SEM. The durability of reinforced glass fiber was investigated with different shapes of nanofillers using sonication rinsing method. Fatigue test was performed to evaluate the adhesion of reinforcing interface and stability of nanofiller coating layer for single fiber reinforced composites. Apparent modulus and conductivity of nanofiller coating layer were evaluated to realize multifunctional of nanocomposites. Fiber type of nanofiller was better than plate type due to better cohesion between fiber and nanofillers. At last, the stability of fiber type nanofiller of coating layer has better durability and conductivity than plate type case.