• 한국생산제조학회지
• /
• 제24권2호
• /
• pp.160-165
• /
• 2015

The 14k, 45k, and 70k Mw PCL have different crystallization temperatures and therefore have slightly different characteristics affecting the fiber diameter. To observe these behaviors, the fiber was produced at every step of $10^{\circ}C$ for each molecular weights and the diameter was measured. Moreover, the fiber was fabricated over the cooled ground plate to observe the change in fiber diameter in comparison to the normal ground plate. In case of molecular Mw 14k PCL, the diameter increased as the temperature increased. For Mw 45k PCL, the fiber diameter decreased as the temperature increased. As of Mw 70k PCL, the fiber diameter decreased with increasing temperature as well. When the experiment was conducted over the cooled collector plate, the data did not change significantly from the previous lexperiments.

• Advanced Composite Materials
• /
• 제16권3호
• /
• pp.245-258
• /
• 2007

The single-modal Weibull model has been assessed on Tyranno ZMI Si-Zr-C-O fiber if a set of shape and scale parameters accurately reproduced the effect of the size of the diameter on strength. The tensile data of a single fiber have been divided into two expedient groups as 'small diameter' group and 'large diameter' group in deriving the parameters, which should be consistent if the Weibull model accurately reproduced the size effect. However, the derived Weibull parameters were inconsistent between the two groups. Thereby the authors have concluded that the parameters of the single-modal Weibull model are dependent on the fiber diameter, so that the model is inadequate to reproduce the strength size effect. On the other hand, Weibull parameters were found consistent between the two groups by excluding the data of 'large mirror zone' sample, which was defined as the sample around 10% mirror zone area of the fracture surface. What is more, the exclusion reduced the strength variance more drastically in the 'large diameter' group than in the 'small diameter' group, even though the 'large mirror zone' samples were found identical in the percentage between the two groups. The authors therefore conclude that diameter limitation to the 'small diameter' group level can lead to drastically less distributed strength values than the estimated strength through the Weibull scaling on the present Tyranno ZMI Si-Zr-C-O fiber.

• 한국항해항만학회지
• /
• 제32권9호
• /
• pp.723-727
• /
• 2008

Sensing performances of evanescent field absorption (EFA) hetero-core fiber sensor has been presented based on EFA by changing the length and the core diameter of the single mode fiber. Experimental results have demonstrated a good feature in their relationship between the length and the core diameter of the single mode fiber. The sensor consists of 2 fiber optics which have the same cladding diameter of $125{\mu}m$ However one fiber optic used is single mode and has varying core diameter ranging from 3.3 to $5.6{\mu}m$. The other fiber is multimode type and has a thicker fixed core diameter of $62.5{\mu}m$. The 2 fiber optics are thermally spliced together. Experiments conducted to measure the resonance wavelength were carried out over a range of refractive index, to find the optimum sensing length Experiments show that core diameter of the single mode fiber and sensing length offects the linearity and sensitivity.

• Macromolecular Research
• /
• 제16권4호
• /
• pp.314-319
• /
• 2008

An image analysis processing method for the measurement of nanofiber diameter was developed. For the analysis, scanning electron microscopy (SEM) images of electrospun fiber were prepared and applied to the individual measurement of the fiber diameter by using the developed and the traditional manual methods. Both methods provided a similar fiber distribution. The fiber average diameters were similar but the variance of the new method was larger than that of the manual method. The average diameters from the two methods exhibited a linear relationship with a high coefficient. The developed method can be used as a practical tool to estimate the fiber diameter of the electro spun web.

• 한국통신학회논문지
• /
• 제12권4호
• /
• pp.335-346
• /
• 1987

光纖維 內에서 後方散亂을 일으키는 주된 要因은 光纖維 構成物質의 密度 不均一과 코어變化에 의해 發生하는 Rayleigh散亂이다. 이 後方散亂에 의해 發生하는 後方散亂 光電力은 optical time domain reflectometer로 檢出할 수 있다. O.T.D.R. 시스템으로 檢出한 後方散亂 光電力은 光纖維 길이에 따른 電力減衰情報와 光纖維 코어의 直徑變化에 관한 情報들을 포함하고 있다 따라서 本 論文에서는 avalanche photodiode의 飽和狀態를 除去할 수 있는 2$\times$2fiber directional coupler와 S/N比를 增加시키는 gated integrato와 timing control circuit를 첨가하여 O.T.D.R. 시스템을 構成하였으며, 構成한 O.T.D.R 시스템으로 後方散亂 光電力을 檢出하여 光纖維 內 코어의 直徑變化를 測定하였다.

• Journal of the Korean Wood Science and Technology
• /
• 제50권6호
• /
• pp.392-403
• /
• 2022

Currently, composite board manufacturing using natural fibers has the potential to expand owing to environmental awareness. To produce a composite board, treatment is required to improve the mechanical and physical properties of the natural fibers. In this study, sodium chloride (NaCl) was used for the chemical treatment. However, studies on chemical treatments using NaCl are limited. This study aimed to investigate the characteristics of kenaf fibers after NaCl treatment. The NaCl treatment concentrations were 1, 3, and 5 wt.% at room temperature, with soaking durations of 1, 2, and 3 h. The tensile strength, strain, and Young's modulus were measured to evaluate the mechanical properties of the fibers. The fiber bundle diameter, weight change owing to treatment, and contact angle were determined to analyze the effect of NaCl treatment. The kenaf fiber bundle treated with 5 wt.% NaCl for 3 h exhibited the highest tensile strength, Young's modulus, reduction in fiber bundle diameter, weight change, and decrease in contact angle compared to those of untreated fiber bundles. The tensile properties of the fiber bundle exhibited a tendency to decrease with increasing fiber bundle diameter. Increasing the soaking duration from 1 to 2 h did not result in a significant decrease in the fiber bundle diameter or an increase in tensile strength. However, a further increase in the soaking duration from 2 to 3 h resulted in a considerable decrease in the fiber bundle diameter and an increase in the tensile strength.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2001년도 봄 학술발표회 논문집
• /
• pp.55-60
• /
• 2001

Influencing factors on flexural toughness of ring-type fiber reinforced concrete(RSFRC) are investigated. An experiment proceeding ASTM C 78 is peformed to make a comparison between ring-type fibers and double-hook type fibers. Most specimen with ring type fibers have failed by the cone type failure, while discrete hook type fibers have failed by fiber pullout. For the hook-type fiber reinforced concrete(SFRC), the first crack load increases, as the fiber mixing volume increases. Aspect ratio(fiber length/fiber diameter) is critical for hook type fibers, so the flexural toughness increases significantly, as the length of fiber increases. However, for the ring type, the toughness indices Increase as the number of fibers in the specimen increases. Since there is no bond problem between the ring fiber and the concrete matrix, the aspect ratio does not affect the performance of the composite material with the newly developed steel fibers. Influencing factors with respect to flexural toughness RSFRC were observed to be ring diameter, diameter of steel fiber and fiber content.

• 한국가구학회지
• /
• 제21권1호
• /
• pp.54-61
• /
• 2010

This study was carried out to identify the differences of some macro and microanatomical features between Eunsasi poplar (Populus tomentiglandulosa T. Lee) and Konara oak (Quercus serrata Thunb.). Anatomical features such as vessel and fiber diameter, cross sectional area of ray parenchyma and endwall pit aperture diameter in ray parenchyma were compared. Differences of anatomical features between two species were found statistically significant. Earlywood vessel diameter in poplar and oak increased from pith to bark while it was found almost stable in latewood. Fiber diameter in poplar was higher than oak fiber. Ray area and the pit aperture diameter in endwall of ray parenchyma were found higher in oak than those in poplar.

• 대한기계학회논문집
• /
• 제16권2호
• /
• pp.200-206
• /
• 1992

The effect of fiber diameter and gauge length on pull-out test for the interfacial properties in fiber reinforced resin composites have been investigated and these results have been arranged as statistical analysis. The fiber and matrix resins used for this study were stainless steel fiber (SUS316) and carbon fiber (high strength type), epoxy and high density polyethylene resin. From this study, it has been found that shear strength are constant regardless of gauge length of pull-out test and coefficient of variation depend on fiber diameter. In addition, it has been found that the interfacial shear strength decreased with the increasing fiber diameter, and in all case, Weibull parameter (m) has approximately 1.2/C.O.V.

• 한국정보기술학회 영문논문지
• /
• 제10권1호
• /
• pp.25-36
• /
• 2020

Motivation: Fibers as the extracellular filamentous structures determine the shape of the cytoskeletal structures. Their characterization and reconstruction from a 3D cellular image represent very useful quantitative information at the cellular level. In this paper, we presented a novel automatic method to extract fiber diameter distribution through a pipeline to reconstruct fibers from 3D fluorescence confocal images. The pipeline is composed of four steps: segmentation, skeletonization, template fitting and fiber tracking. Segmentation of fiber is achieved by defining an energy based on tensor voting framework. After skeletonizing segmented fibers, we fit a template for each seed point. Then, the fiber tracking step reconstructs fibers by finding the best match of the next fiber segment from the previous template. Thus, we define a fiber as a set of templates, based on which we calculate a diameter distribution of fibers.