• Nuclear Engineering and Technology
• /
• v.31 no.4
• /
• pp.375-384
• /
• 1999

The credibility of CHECWORKS FAC model analysis was evaluated for plant application in a model plant chosen for demonstration. The operation condition at each pipe component was defined before the wear rate analysis by plant data base, water chemistry analysis, and network flow analysis. The predicted wear was compared with the measured wear for 57 sample components selected from 43 susceptible line groups analysed. The inspected 57 locations represent components of highest predicted wear in each line group. Both absolute value and relative ranking comparisons indicated reasonable correlations between the predicted and the measured values. Four components showed much higher measured wear rates than the predicted ones in the feed water train from main feed water pump discharge to steam generator, probably due to high hydrazine concentration operation the effect of which had not been incorporated into the CHECWORKS model. The measured wear was higher than the predicted one consistently for components with least susceptibility to FAC. It is believed that the conservatism maintained during UT data analysis dominated the measurement accuracy. A great deal of enhancement is anticipated over the current plant pipe management program when a comprehensive plant pipe management program is implemented based on the model analysis.

• Asian-Australasian Journal of Animal Sciences
• /
• v.21 no.6
• /
• pp.912-916
• /
• 2008

Pre-slaughter conditions affect poultry meat quality. Therefore, stresses before slaughter like heat stress, struggle and shackling on the shackle line, crating and transport and feed withdrawal are very important for the poultry industry in respect of quality as well as welfare of the birds. However, exposure to heat in oxidative stress can in turn lead to cytotoxicity in meat type birds. Chickens exposed to heat stress before slaughter showed the lowest ultimate pH and birds shackled for a longer time the highest. The abdominal fat content was higher in heat stressed birds. Struggling on the shackle line hastened the initial rate of the pH drop and increased the redness of breast meat. Again, with increasing struggling activity, lactate concentration in breast muscle of chicken increased. Paler meat was found in birds that were transported for a longer time than in those after a small journey or not transported. The pre-slaughter and eviscerated weights were decreased as the length of feed withdrawal period increased.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.8
• /
• pp.178-185
• /
• 1999

In tool condition monitoring systems, parameters should be set to a certain threshold. In many cases, however, the threshold is dependent on cutting conditions, especially the radial immersion ratio. In this presented is a method of on-line estimation of the radial immersion ratio in face milling. When a tooth finishes sweeping, a sudden drop of cutting force occurs. The force drop is equal to the cutting force that acting on a tooth at the swept angle of cut and can be acquired from cutting force signals in feed and cross-feed directions. Average cutting force per tooth period can also be calculated from cutting force signals in two directions. The ratio to cutting forces in two directions acting on a tooth at a certain swept angle of cut and the ratio of average cutting forces in two directions per tooth period are functions of the swept angle of cut and the ratio of radial to tangential cutting forces. Using these parameters, the radial immersion ratio is estimated. Various experiments are performed to verify the proposed method. The results show that the radial immersion ratio can be estimated by this method regardless of other cutting conditions.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.10
• /
• pp.2065-2071
• /
• 2011

The external quality factor ($Q_e$) is controlled by coupling condition between resonator and input/output ports in design of microwave filter. In this paper, we represent extracting method of external quality factor using phase response for resonator with input/output ports according to position of feed line from microstrip line resonator. The results regarding to position, coupling gap and line width for tapped line and coupled line structure are represented, and we got the exact $Q_e$ value from the this method. This results will be applied to coupled resonator filter design.

• Asian-Australasian Journal of Animal Sciences
• /
• v.20 no.1
• /
• pp.82-88
• /
• 2007

Two experiments were conducted to see the effects of lacquer meal (Rhus verniciflua) on layer performance. In Exp. 1, seventy-two Hy-Line brown layers, 46 wk of age were fed 0, 1.5% and 3.0% lacquer added diets for 6 weeks. Diets contained 2,650 kcal/kg ME and 16.50% CP. In Exp. 2, high-energy diets were fed to 72 Hy-line brown layers of 46 wk age for 6 wk. The diets were: control (3,000 kcal/kg ME and 16.50% CP); T1 and T2 contained 1.5 and 3.0% lacquer respectively, in addition to high energy levels. Each treatment had four replicates with 6 birds each in both the experiments. During Exp.1, there was no effect on average daily feed intake, egg production and feed efficiency, however, egg weight was linearly (p=0.0128) decreased with the addition of lacquer in diets. The egg quality parameters measured at bi-weekly intervals did not reveal any particular trend. In Exp 2., high-energy diets have decreased the feed intake and egg production in all groups. However, feeding lacquer at 1.5% increased the egg production by 9% than control. The yolk fat content was increased due to treatments showing quadratic trend (p=0.0683). The liver fat content was decreased by 40-43% than control in lacquer added diets. Except palmitic, oleic and arachidonic acids, some yolk fatty acids showed a linear decreasing trend in lacquer diets. The serum triglycerides and total cholesterol levels were not influenced with lacquer in the diets; however, the serum glucose level was linearly decreased with the addition of lacquer. In conclusion, lacquer meal supplementation significantly affected the performance of layers fed high-energy diets.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.1
• /
• pp.156-161
• /
• 1992

In this research a monitoring system for turning using NC information and the current of feed motor as a monitoring signal was developed. The overall system consists of modules such as learning process, NC data transmission, generation of forecast information, signal acquisition, monitoring and post process. In the learning process, the reference data and the cutting force equation necessary for monitoring are obtained from the accumulated monitoring results. In the generation of forecast information, the information of forecasted cutting forces is acquired from the cutting force equation and NC program and appended to each NC block as a monitor code. Reliability of monitoring is improved by using the monitor code in the real-time monitoring. Monitoring module is divided into two parts : the off-line monitoring where errors of NC program are checked and the on-line monitoring where the level of motor current is monitored during cutting operations. If the actual current level exceeds the limit value provided by the monitor code in the level monitoring, it is recognized as abnormal. In the event of abnormal status, the post processor sends the emergency stop signal to NC controller to stop the operation. Actual experiments have shown that the developed monitoring system works well.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.2
• /
• pp.133-145
• /
• 1996

This paper presents an indirect cutting force measuring system, which uses the current signals from the AC servo drive units of the horizontal machining center, with its applications to the adaptive regulation of the cutting forces in various milling processes and to the on-line monitoring of tool breakage. A typical model for the feed-drive control system of a horizontal machining center is developed to analyze cutting force measurement from the drive motor. The pulsating milling forces can be measured indirectly within the bandwidth of the current feedback control loop of the feed-drive system. It is shown that the indirectly measured cutting force signals can be used in the adaptive controller for cutting force regulation. The whole scheme has been embedded in the commercial machining center and a series of cutting experiments on the face cutting processes are performed. The adaptive controller reveals reliable cutting force regulating capability against the various cutting conditions. It is also shown that the tool breakage in milling can be detected within one spindle revolution by adaptively filtering the current signals. The effect of the cutter run-out has been considered for the reliable on-line detection of tool breakage.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.8
• /
• pp.1492-1497
• /
• 2017

In this paper, a design method for a CPW-fed wideband loop antenna for indoor digital TV applications is studied. The proposed loop antenna consists of a square loop and two circular sectors which connect the loop with central feed points, and the CPW feed line is inserted in the lower circular sector. The CPW feed line is designed to match with the 75 ohm port impedance for DTV applications, and the ground slots are etched in order to improve the impedance matching in the middle frequency region. The effects of the gap between the circular sectors and the location and dimension of the ground slots on the input reflection coefficient and gain characteristics are examined to obtain the optimal design parameters. The optimized antenna is fabricated on FR4 substrate, and the experiment results show that it operates in the frequency band of 463-1,280 MHz for a VSWR < 2, which assures the operation in the DTV band.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.5
• /
• pp.559-569
• /
• 2012

In this paper, the X($1{\times}2$, 10.525 GHz) and K($3{\times}6$, 24.15 GHz) bands patch array antenna having single feed line for radar detector applications is proposed. The left side of the proposed array antenna is X band array antenna and the right is K band array antenna. Two array antennas with two stubs located in the front of antennas are fed through one transmission line. If the array antennas which have the different resonance frequency are fed by one transmission line using general T-junction, it interferes each other and the array antenna lost its character. Therefore, to prevent these interferences, two stubs using open and short property of stub are designed. First of all, the performances of array antenna weren't changed when each array antennas were connected with the stub and in the end, it is found out that it was the same when the two array antennas were combined and feed through the one transmission line. The measured gain at X band is 6.47 dBi and measured gain at K band is 13.07 dBi. The experimental results agree well with the simulated ones.

• Korean Journal of Poultry Science
• /
• v.7 no.1
• /
• pp.31-42
• /
• 1980

In order to identify the best superior cross combination of breeder stocks for broiler production, combining ability test and analyses of phenotypic performances for parent stocks were examined on records of 1,440 broiler chicken which were produced from 4 parental strains and 3 maternal strains at Hanhyup Poultry Breeding Farm from September 28, 1978 to January 5, 1979. The results obtained were as follows; 1. There was not found heterosis effect in viability but it seems to be desirable to select Hubbard strain in paternal line to improve viability. 2. As the paternal and maternal lines, selection of Ross strain showed the best paternal and maternal performance and the best general combining ability in body weight at 8 weeks of age is expected to be able to improve body weight of it s crossbred And the most superior cross combinations based on the specific combining ability and performance of rack crossbred were identified as Hubbard x Ross ana Ross x Hypeco crossbreds. 3. The best paternal and maternal lines on the smallest feed consumption for 8 weeks were Hubbard and Ross strains, and Hypeco strain, respectively. Especially Hubbard x Hypeco cross combination was proved as the smallest feed consumption compared with other cross combinations. 4. In feed requirement per Kg body weight increase, Hubbard strain for paternal line, Hypeco strain for naternal line, and cross combinations of Hubbard x Hypeco, Hubbard x Ross and Ross x Hypeco were certified as the most superiors. 5. Also superior cross combinations of Hubbard x Hypeco and Hubbard x Ross earned the most profit per bird through economic analysis. According to results as shown above, this experiment seems to be able to reach a such conclusion that production of superior cross combinations Hubbard x Ross, Hubbard x Hypeco and Ross x Hypeco through selection of Ross and Hubbard strains to paternal line and Hypeco and Ross strains for maternal line may become to considerable improvement for important economic characters of broiler; viability, body weight, feed consumption and feed requirement.