• Advanced Composite Materials
• /
• 제18권4호
• /
• pp.339-350
• /
• 2009

Al-Fe-V-Si alloys reinforced with SiC particles were prepared by multi-layer spray deposition technique. Both microstructures and mechanical properties including hardness and tensile properties development during hot exposure process of Al-8.5Fe-1.3V-1.7Si, Al-8.5Fe-1.3V-1.7Si/15 vol% $SiC_P$ and Al-10.0Fe-1.3V-2Si/15 vol% $SiC_P$ were investigated. The experimental results showed that an amorphous interface of about 3 nm in thickness formed between SiC particles and the matrix. SiC particles injected silicon into the matrix; thus an elevated silicon concentration was found around $\alpha-Al_{12}(Fe,\;V)_3Si$ dispersoids, which subsequently inhibited the coarsening and decomposition of $\alpha-Al_{12}(Fe,\;V)_3Si$ dispersoids and enhanced the thermostability of the alloy matrix. Moreover, the thermostability of microstructure and mechanical properties of Al-10.0Fe-1.3V-2Si/15 vol% $SiC_P$ are of higher quality than those of Al-8.5Fe-1.3V-1.7Si/15 vol% $SiC_P$.

• 자원리싸이클링
• /
• 제20권5호
• /
• pp.34-39
• /
• 2011

금속급 실리콘(MG-Si)에 Ca을 첨가하여 Ar 분위기 중의 1500$^{\circ}C$ 에서 용융하고, 10$^{\circ}C$/min의 속도로 상온까지 응고하여 왕수로 침출하였다. 본 연구에서는 금속급 실리콘 중의 Fe와 P의 제거에 미치는 Ca 첨가의 영향과 산 침출 조건의 영향에 대하여 조사하였다. Ca 첨가에 의해 MG-Si의 결정립계에 CaSi$_2$상이 생성되고, CaSi$_2$상 내에 FeSi$_2$상이 석출된 것을 확인하였다. 이러한 CaSi$_2$상 등의 생성에 의해 600~850${\mu}m$ 크기의 MG-Si에서도 30% 이상의 왕수를 이용한 침출로 Fe의 97%, P의 66%까지 제거할 수 있었다.

• 한국주조공학회지
• /
• 제23권2호
• /
• pp.77-85
• /
• 2003

Some alloying elements such as Cr, B, Ti and Si were added individually or as a mixture to Fe-30 at.%Al alloys. The alloys were melted using an arc furnace and then heat-treated for homogenization at 1000$^{\circ}C$ for 7 days and followed by rolling at 1000$^{\circ}C$. The alloying elements on rolling characteristics were investigated by the microstructures and fracture mode before and after rolling. The microstructures before rolling showed that all of the alloys had equiaxed grains. On the other hand, the microstructures of rolling plane as well as its perpendicular plane became elongated after rolling. The alloys such as Fe-30Al, Fe-30Al-3Ti, Fe-30Al-0.5B, Fe-30Al-5Cr and Fe-30Al-3Ti-0.5B revealed better rolling behaviour from the point that intergranular and cleavage fractures were not fundamentally occurred. But the addition of 5Ti or 3Si to Fe-Al alloys had detrimental effects. The Ti-added alloy system such as Fe-30Al-5Ti, Fe-30Al-5Ti-5Cr, Fe-30Al-3Ti-5Cr and Fe-30Al-5Ti-0.5B were cracked through grain and showed cleavage fracture. The Si-added alloy system such as Fe-30Al-5Si, Fe-27Al-3Si and Fe-27Al-5Cr-3Si were cracked along the grain boundary and showed intergranular fracture. $DO_3{\leftrightarrow}B_2$ transition temperature of Fe-30at.%Al alloy was 520$^{\circ}C$, whereas the addition of 3Ti and 3Ti+0.5B comparably increased the temperature to 797 and 773$^{\circ}C$, respectively.

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2001년도 추계연구발표회 논문개요집
• /
• pp.48-49
• /
• 2001

• 대한화학회지
• /
• 제54권5호
• /
• pp.579-581
• /
• 2010

Solid silica supported ferric chloride ($SiO_2-FeCl_3$) 촉매를 이용하여 다양한 benzimidazoles의 one-step 합성을 수행하였으며, 합성 방법이 간단하며, 화합물의 분리가 용이하며, 반응시간이 짧다.

• 한국자기학회지
• /
• 제19권2호
• /
• pp.62-66
• /
• 2009

연자성 금속재료인 $Fe_{94}Si_5Cr_1$을 30시간 볼밀 한 후 주사전자현미경을 사용하여 관찰한 결과 볼밀 가공한 FeSiCr의 입자들이 구형에서 편상으로 변함을 확인하였다. FeSiCr을 실리콘 고무와 혼합하여 핸드폰용 전파흡수체를 제조하고 network analyzer을 이용하여 두께에 따른 FeSiCr-고무 전파흡수체의 전파흡수특성 및 재료정수를 측정하였으며, 그들의 상관관계를 비교 조사하였다. 그 결과 sheet형 전파흡수체 두께에 따라서 정합주파수가 낮은 주파수 대역으로 shift 됨을 알 수 있고, 1.3 mm의 두께로 제조한 전파흡수체에서는 이동통신주파수 대역인 1.86 GHz에서 -8.3 dB의 반사손실을 보여주었다.

• 한국분말재료학회지
• /
• 제1권1호
• /
• pp.66-71
• /
• 1994

Optical microstructures and mechanical properties of Na gas atomized Al-20Si-5Fe alloying powder and its hot extrudates were studied on 3 different types of powder size distribution. This powder showed the size distribution of 10~210 $\mu\textrm{m}$. Also the microstructures of $\alpha$-Al, primary and eutectic Si and needle shaped intermetallic compounds were observed by optical microscope. These needle shaped intermetallic compounds were identified as ${\delta}Al_4FeSi_2$- by XRD and EDX analysis. The ultimate tensile strength(UTS) of these alloy extrudates was increased from 324 to 390 MPa with decreasing powder size range from 120~210 $\mu\textrm{m}$ to 10~64 $\mu\textrm{m}$. A value of Micro-vic-kers hardness was simillar to the result of UTS. These extrudates showed better wear resistance than those of Al-20Si-2X(X : Ni, Cr, Zr), although they are insensitive to the size distribution. These results indicate that the presentation of ${\delta}Al_4FeSi_2$ intermetallic compounds contributed to the wear resistance improvement.

• 한국결정성장학회지
• /
• 제10권1호
• /
• pp.36-41
• /
• 2000

본 실험에서는 D.C magnetron sputtering을 사용하여 Ni-Fe/Co-Fe/Mn-Ir/Cu/buffer/Si 다층박막의 교환이방성에 관하여 연구하였다. 일반적인 Ni-Fe/Mn-Ir/buffer(Cu)/Si의 다층박막 구조는 낮은 교환결합 자계에 의하여 강자성체를 완전히 고착시키지 못한다. 따라서 Ni-Fe/Mn-Ir/buffer/Si 다층박막의 $H_{ex}$를 증가시키기 위해 하지층으로 Cu/Ta을 사용하여 Mn-Ir막의 결정립 부피를 증가시키고 Ni-Fe.Mn-Ir계면에 Co-Fe을 삽입하여 반강자성체/강자성체 계면에서의 epitaxy 경향을 향상시켜 2배 이상의 $H_{ex}$의 증가를 얻을 수 있었다. 또한 ferromagnete/Mn-Ir/buffer/Si의 다층박막 구조에서는 Mn-Ir거 두께에 따른 He일 변화 거동은 Mn-Ir/ferromagnete/buffer/Si다층박막구조와는 다른데 이와 같은 이유는 적층순서에 따라서 반강자성체 결정립의 부피분포와 계면에서의 교환결합 에너지가 차이가 나기 때문인 것으로 사료된다.

• 한국전기전자재료학회논문지
• /
• 제27권7호
• /
• pp.462-467
• /
• 2014

In this paper, we studied the magnetic composite sheets for electromagnetic wave noise absorber of quasi-microwave band by using soft magnetic FeSiCr and Fe50Ni flakes with the thickness of about $1{\mu}m$ and polymer. The magnetic hysteresis curve including saturation magnetization and residual magnetization and the complex permeability characteristics of the composite sheets were investigated to clarify the mixing effect on electromagnetic wave absorption properties. The saturation magnetization was decreased about 10% while the residual magnetization was increased about 15% and the real parts of complex permeability at below 500 MHz were increased 0.6~4 while those values at above 500 MHz were decreased 0.4~2.5 according to the change of contents of FeSiCr and Fe50Ni powders. As a result, the reflection loss can be moved to the lower frequency from 2~3 GHz to 1~1.5 GHz as the contents of Fe50Ni flaky powder into FeSiCr flaky powder was increased up to 50%.

• 한국재료학회지
• /
• 제33권9호
• /
• pp.353-359
• /
• 2023

This study investigated the growth behavior and characteristics of compounds formed at the interface between a liquid Al-Si-Cu alloy and solid cast iron. Through microstructural analyses, it was observed that various AlFe and AlFeSi phases are formed at the interface, and the relative proportion of each phase changes when small amounts of strontium are added to the Al alloy. The results of the microstructural analysis indicate that the primary phases of the interfacial compounds in the Al-Si-Cu base alloy are Al₈Fe₂Si and Al_4.5FeSi. However, in the Sr-added alloys, significant amounts of binary AlFe intermetallic compounds such as Al₅Fe₂ and Al₁₃Fe₄ formed, in addition to the AlFeSi phases. The inclusion of Sr has a slight diminishing effect on the rate at which the interfacial compounds layer thickens during the time the liquid Al alloy is in contact with the cast iron. The study also discusses the nano-indentation hardness and micro-hardness of the interfacial phases.