• 한국토양비료학회지
• /
• 제45권1호
• /
• pp.103-106
• /
• 2012

To investigate distribution characteristics of heavy metals in soils in the vicinity of King Sejong Station of King George Island, Antarctica, Fe, Mn, Cu, Zn, Pb, Co, Cd, Cr, Ni and Mo contents were investigated under different distances and directions from King Sejong Station. 13 sample sites were distributed from King Sejong Station. In site 4, the Cd content was higher than that in other sites. The Cr content was the highest in site 9, and the Ni and Mn contents were high in site 12. Cu, Co and Zn were highly contained in distance 1~2 km from King Sejong Station. Cd, Cr, Ni and Mo contents were lower, whereas Fe, Mn, Cu, Zn, Pb and Co contents were higher than other heavy metal contents at all sites.

• 한국산학기술학회논문지
• /
• 제21권3호
• /
• pp.576-584
• /
• 2020

압출기 스크류 소재는 주로 냉간 금형 공구강(SKD11)이 사용되고 있는데, 최근 합성 수지의 발달로 화학적 부식 및 마모 발생이 증가하고 있다. 이를 개선하기 위해 내마모성과 내식성이 우수한 고크롬 주철의 사용이 요구되지만, 난가공성으로 사용이 기피되고 있다. 본 연구에서는 고크롬 합금의 난가공성을 개선하기 위해 Fe-23Cr-2.5C-1.2Si-1.08Mn-0.48Mo-0.3V 조성의 고크롬 주철에 가공성이 우수한 니켈을 0, 0.5, 1.0, 1.5 % 첨가하여 주조하고 열처리를 진행한 후, 선삭 시험과 동전위 분극 시험을 통해 니켈이 피삭성 및 내식성에 미치는 영향을 분석하여 SKD11과 비교하였다. 고크롬 주철은 고주파 진공유도용해로를 사용하여 주조하고, 이후 750 ℃에서 5시간 동안 풀림 처리와 풀림 처리 후 1100 ℃에서 5시간동안 재열처리를 실시하였다. 750 ℃ 풀림 처리 후 선삭 시험을 실시한 결과 니켈의 함량이 1.0% 이상에서 피삭성은 현저히 향상되었다. 5% NaCl 용액에서 동전위 분극 시험 결과 주방상태와 750 ℃ 풀림 처리에서는 니켈의 함량이 증가할수록 내식성은 저하되었으나, 1100 ℃ 재열처리 후에는 1.5% 니켈에서 가장 우수한 내식성을 나타냈다.

• 동력기계공학회지
• /
• 제14권1호
• /
• pp.59-64
• /
• 2010

Ferritic stainless steel is currently increasingly used for automotive exhaust material. The material for exhaust manifold is used in the temperature range of 500∼$850^{\circ}C$. Therefore, high temperature characteristic is an important one that affects it's life span. It has been investigated the effect of alloying elements of Cr, Mo, Nb, Ti in the ferritic stainless steel for exhaust manifold on the high temperature tensile strength. There was a few difference in the tensile strength at $600^{\circ}C$ with the exception of low Cr steel, but the steels containing higher Cr, Mo or Nb elements showed significantly higher tensile strength at the temperature of $800^{\circ}C$. The precipitates of the specimens after heat treating at the test temperature were electrolytic extracted, and quantitatively analysed using by SEM-EDS and TEM. The alloying elements of Cr and Mo increased the tensile strength as a solid solution strengthener, and on the other hand Nb element enhanced the strength by forming the fine intermetallic compounds such as NbC or $Fe_2Nb$.

• 약학회지
• /
• 제45권5호
• /
• pp.460-467
• /
• 2001

Heavy metals, such as Al, As, Cd, Cr Cu, Fe, Hg, Mn, Mo, Ni, Pb, Se, Si, Sn, V and Zn, were analysed on kidney cortex and medulla of Korean obtained from 154 forensic medical autopsy cadavers. Heavy metals were analysed by inductively coupled plasma atomic emission spectrometry In kidney cortex, the concentrations of Al, Cd, Cu, Mn, Mo, Pb, Se, Si and Zn were significantly higher than in the kidney medulla (Cd, Cu, Mn, Mo, Zn : p<0.01, AA, Pb, Se, Si : p<0.05). No significant local differences were found between kidney cortex and kidney medulla in the concentrations of As, Cr Fe, Hg, Ni, Sn and V. In kidney cortex and kidney medulla, Cd concentrations correlated positively with age, but Mn concentrations correlated negatively with age. A significantly positive correlation between Cd and Zn, Cd and Cu, Zn and Cu, Al and Si, Se and As was found in kidney cortex and kidney medulla. A significantly positive correlation between Hg and Se was only observed in kidney cortex. These results indicate that the distribution of hazardous heavy metals is similar to that of essential elements in the tissues.

• 분석과학
• /
• 제20권6호
• /
• pp.524-528
• /
• 2007

Variations of the twenty one metal components (Mg, Al, V, Cr, Co, Sr, Ba, Na, K Mn, Fe, Cu, Zn, As, Hg, Pb, Ca, P, Mo, Cd, Sb) were analyzed in human hair sample by inductively coupled plasma mass spectrometry (ICP-MS). The effect of bleach and permanent wave manipulation on the elemental composition of hair were investigated. It was found that the composition of hair varied with hair bleach and permanent wave. Hair sample was collected from male in the age of thirties. Hair sample (0.05 g) was added to the Teflon digestion bomb together with 1.5 mL of nitric acid and an appropriate amount of In as an internal standard. The sample was then decomposed in the microwave digestion system. In normal hair, the contents of V, Cr, Mn, Fe, Co, Cu, Zn, As, Mo, Cd, Sb and P were increased in permanent wave hair, and Mg, Al, V, Co, Sr, Ba, Na and K were increased in bleached hair. But Mg, Al, Sr, Ba, Hg, Pb, Na, K, and Ca contents were decreased with permanent wave hair, Mn, Fe, Cu, Zn, As, Hg, Pb and Ca contents were decreased with bleached hair.

• Journal of Welding and Joining
• /
• 제19권5호
• /
• pp.506-511
• /
• 2001

Weld overlay has been developed to improve the property of material surface which is used in the severe environment. Weld overlay is the process which uses an arc heat and welds different composition of alloy on the substrate for the improvements of heat resistance and wear resistance. Weld overlay has a lot of advantages which are high hardness, good processing efficiency, easy controlling of layer thickness, good quality and low cost. In this study, weld overlay was performed by MAG welding on the base metal(SS400) with filler metal which contain composite powders(Cr+C+Mn+Mo+NbC) and solid wire(JIS-YGW11). Characterization of hardness and wear resistance were analyzed by EDS, EPMA, XRD and observations of microstructure were performed to investigate characteristics of overlays. The experimental results of overlaid specimens manufactured with Cr+C+Mn+Mo+NbC powders were obtained as fellows. ${\alpha}-phase$, M(Fe, Cr)3C and NbC of overlays were increased with decreasing the wire feed rates and increasing powder feed rates. Also the hardness of overlays were increased and the specific wear were decreased.

• 한국재료학회지
• /
• 제21권11호
• /
• pp.592-595
• /
• 2011

It is well known that modified 9Cr-1Mo steel has a low thermal expansion and high thermal conductivity with excellent high temperature properties compared to austenitic stainless steel. For these advantages, the steel is very popular for the boiler tube of thermal power plants. Normalizing is commonly utilized to obtain martensite in this steel, which shows an unusual toughness for martensite. However, some accidents related to this steel have been reported recently, opening the necessity for further study. As a particular behavior of the steel, an abrupt drop of the impact value has been identified upon tempering at 750$^{\circ}C$ for about 1 hour. It is well known that $Fe_3C$ forms during autotempering and turns to $Cr_2C$ at an early stage and then transforms to $Cr_{23}C_6$. In this study, the cause of the abrupt drop of the impact value was investigated with an impact test, microstructural observation, nanodiffraction and phase analyses using instruments such as optical and transmission electron microscopes (TEM) with an extraction carbon replica of the carbides. The analyses revealed that the $M_2C$ that formed when retained for about 1 hour at 750$^{\circ}C$ causes a drastic decrease in the mechanical properties. The sharp drop in mechanical properties, however, disappeared as the $M_2C$ transformed into $M_{23}C_6$ with longer retention.

• Structural Engineering and Mechanics
• /
• 제44권5호
• /
• pp.601-609
• /
• 2012

Effect of different crack sizes on fracture criterion of some engineering materials was investigated in this work. Using finite element (FE) method coupled with a newly developed algorithm, J-integral values for different crack sizes were obtained for single-edge notched bend (SENB) and compact type (CT) specimen. Specimens with initial a/W ratio from 0.25 to 0.75 varying in crack size in steps of 0.125 were investigated. Several different materials, like 20MnMoNi55, 42CrMo4 and 50CrMo4, usually used in engineering structure, were investigated. For one of mentioned materials, numerical results were compared with experimental and their compatibility is visible.

• 한국광물학회지
• /
• 제32권3호
• /
• pp.223-234
• /
• 2019

삼덕 Mo 광상 주변지질은 고생대 화전리층, 고운리층, 서창리층, 이원리층, 황강리층, 백악기 우백질 반상화강암 및 화강반암으로 구성된다. 이 광상은 서창리층 내에 발달된 NS 방향의 열극대를 따라 충진한 3개조의 석영맥으로 구성된 광상으로 석영맥의 맥폭은 0.05~0.3 m 정도로 팽축이 심하고 석영맥의 연장성은 약 400 m 정도이다. 석영맥은 괴상, 각력상 및 정동조직들이 관찰되며 모암변질로는 규화작용, 견운모화작용, 점토화작용 및 녹니석화작용 등이 관찰된다. 산출광물은 석영, 형석, 백색운모, 흑운모, 인회석, 모나자이트, 금홍석, 티탄철석, 휘수연석, 황동석, Fe-Mg-Mn 산화물 및 철 산화물 등이다. 이 광상의 백색운모는 석영맥과 모암에서 세립질에서 조립질로 산출되며 4가지 산출유형(I 유형: 석영, 휘수연석, 철 산화물 및 Fe-Mg-Mn 산화물과 함께 산출되는 것, II 유형: 석영, 철 산화물 및 Fe-Mg-Mn 산화물과 함께 산출되는 것, III 유형: 석영 및 흑운모와 함께 산출되는 것 및 IV 유형: 석영과 함께 산출되는 것)을 갖는다. 석영맥에서 산출되는 백색운모의 화학조성은$(K_{0.89-0.60}Na_{0.05-0.00}Ca_{0.01-0.00}Sr_{0.02-0.00})_{0.94-0.62}(Al_{1.54-1.12}Mg_{0.36-0.18}Fe_{0.26-0.09}Mn_{0.04-0.00}Ti_{0.02-0.00}Cr_{0.02-0.00}Zn_{0.01-0.00})_{1.91-1.72}(Si_{3.40-3.11}Al_{0.92-0.60})_{4.00}O_{10}(OH_{1.68-1.42}F_{0.58-0.32})_{2.00}$이나 I 유형의 백색운모는 나머지 유형의 백색운모보다 $SiO_2$ 및 MgO 함량은 낮고 FeO 함량은 높게 나타난다. 또한 이 광상의 백색운모의 화학조성 변화는 팬자이틱 또는 Tschermark 치환($(Al^{3+})^{VI}+(Al^{3+})^{IV}{\leftrightarrow}(Fe^{2+}$ 또는 $Mg^{2+})^{VI}+(Si^{4+})^{IV}$) 및 직접적인 $(Fe^{3+})^{VI}{\leftrightarrow}(Al^{3+})^{VI}$ 치환에 의해 일어났음을 알 수 있다.

• Corrosion Science and Technology
• /
• 제12권6호
• /
• pp.274-279
• /
• 2013

Flow accelerated corrosion (FAC) of the carbon steel piping in nuclear power plants (NPPs) has been major issue in nuclear industry. During the FAC, a protective oxide layer on carbon steel dissolves into flowing water leading to a thinning of the oxide layer and accelerating corrosion of base material. As a result, severe failures may occur in the piping and equipment of NPPs. Effect of alloying elements on FAC of pipe materials was studied with rotating cylinder FAC test facility at $150^{\circ}C$ and at flow velocity of 4m/s. The facility is equipped with on line monitoring of pH, conductivity, dissolved oxygen(DO) and temperature. Test solution was the demineralized water, and DO concentration was less than 1 ppb. Surface appearance of A 106 Gr. B which is used widely in secondary pipe in NPPs showed orange peel appearance, typical appearance of FAC. The materials with Cr content higher than 0.17wt.% showed pit. The pit is thought to early degradation mode of FAC. The corrosion product within the pit was enriched with Cr, Mo, Cu, Ni and S. But S was not detected in SA336 F22V with 2.25wt.% Cr. The enrichment of Cr and Mo seemed to be related with low, solubility of Cr and Mo compared to Fe. Measured FAC rate was compared with Ducreaux's relationship and showed slightly lower FAC rate than Ducreaux's relationship.