• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 2003.09a
• /
• pp.28-35
• /
• 2003

Quaternary faults found around the Ulsan Fault System can be divided into 4 types based on the fault outcrop features : Type I fault cuts basements and Quaternary deposits of which remain on both hangwall and footwall. Type II fault is developed only in Quaternary deposit. Type III fault has inclined unconformity after Quaternary faulting. Type IV fault is common type around the Ulsan fault system and has horizontal unconformity surface after cutting earlier Quaternary deposit. After erosion, later Quaternary deposit overlays on both old deposit and basement. The Ulsan Fault System consists of three segments at large scale from north to south based on the lineament rank and shape, Quaternary fault location, and slip rate. The segment boundaries are identified by the existence of the two intervals which show no lineaments and Quaternary faults. But, if detail fault parameters could be obtained and used in segmentation, it can be divided into more than three segments.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 1997.10a
• /
• pp.49-56
• /
• 1997

Most large strike-slip faults do not rupture their entire length during single faulting but generally break in segments which are different in location and time of faulting. Studies related to the development of the Yangsan fault have been reported based on partial results from characteristics of geolgocial distribution, geophysical prospecting and paleostress analyses. This paper shows, based on preliminary results, that the Yangsan fault could be divided into four structural areas along entire length. These areas are different in geological distribution, bedding attitude measured from sedimentary rocks, strike of main fault, geometry of small faults, termination types of fault tips, cyclic variation of fault zone width, and arrangement of paleostress. Therefore, the Yangsan fault could be divided into at least four segments.

• Earthquakes and Structures
• /
• v.19 no.6
• /
• pp.445-457
• /
• 2020

An ultra-high voltage (UHV) transmission system has the advantages of low circuitry loss, high bulk capacity and long-distance transmission capabilities over conventional transmission systems, but it is easier for this system to cross fault rupture zones and become damaged during earthquakes. This paper experimentally and numerically investigates the seismic responses and collapse failure of a UHV transmission tower-line system crossing a fault. A 1:25 reduced-scale model is constructed and tested by using shaking tables to evaluate the influence of the forward-directivity and fling-step effects on the responses of suspension-type towers. Furthermore, the collapse failure tests of the system under specific cross-fault scenarios are carried out. The corresponding finite element (FE) model is established in ABAQUS software and verified based on the Tian-Ma-Qu material model. The results reveal that the seismic responses of the transmission system under the cross-fault scenario are larger than those under the near-fault scenario, and the permanent ground displacements in the fling-step ground motions tend to magnify the seismic responses of the fault-crossing transmission system. The critical collapse peak ground acceleration (PGA), failure mode and weak position determined by the model experiment and numerical simulation are in relatively good agreement. The sequential failure of the members in Segments 4 and 5 leads to the collapse of the entire model, whereas other segments basically remain in the intact state.

• The Journal of the Petrological Society of Korea
• /
• v.27 no.3
• /
• pp.109-120
• /
• 2018

The distributional characteristics of fault segments in Cretaceous and Tertiary rocks from southeastern Gyeongsang Basin were derived. The 267 sets of fault segments showing linear type were extracted from the curved fault lines delineated on the regional geological map. First, the directional angle(${\theta}$)-length(L) chart for the whole fault segments was made. From the related chart, the general d istribution pattern of fault segments was derived. The distribution curve in the chart was divided into four sections according to its overall shape. NNE, NNW and WNW directions, corresponding to the peaks of the above sections, indicate those of the Yangsan, Ulsan and Gaeum fault systems. The fault segment population show near symmetrical distribution with respect to $N19^{\circ}E$ direction corresponding to the maximum peak. Second, the directional angle-frequency(N), mean length(Lm), total length(Lt) and density(${\rho}$) chart was made. From the related chart, whole domain of the above chart was divided into 19 domains in terms of the phases of the distribution curve. The directions corresponding to the peaks of the above domains suggest the directions of representative stresses acted on rock body. Third, the length-cumulative frequency graphs for the 18 sub-populations were made. From the related chart, the value of exponent(${\lambda}$) increase in the clockwise direction($N10{\sim}20^{\circ}E{\rightarrow}N50{\sim}60^{\circ}E$) and counterclockwise direction ($N10{\sim}20^{\circ}W{\rightarrow}N50{\sim}60^{\circ}W$). On the other hand, the width of distribution of lengths and mean length decrease. The chart for the above sub-populations having mutually different evolution characteristics, reveals a cross section of evolutionary process. Fourth, the general distribution chart for the 18 graphs was made. From the related chart, the above graphs were classified into five groups(A~E) according to the distribution area. The lengths of fault segments increase in order of group E ($N80{\sim}90^{\circ}E{\cdot}N70{\sim}80^{\circ}E{\cdot}N80{\sim}90^{\circ}W{\cdot}N50{\sim}60^{\circ}W{\cdot}N30{\sim}40^{\circ}W{\cdot}N40{\sim}50^{\circ}W$) < D ($N70{\sim}80^{\circ}W{\cdot}N60{\sim}70^{\circ}W{\cdot}N60{\sim}70^{\circ}E{\cdot}N50{\sim}60^{\circ}E{\cdot}N40{\sim}50^{\circ}E{\cdot}N0{\sim}10^{\circ}W$) < C ($N20{\sim}30^{\circ}W{\cdot}N10{\sim}20^{\circ}W$) < B ($N0{\sim}10^{\circ}E{\cdot}N30{\sim}40^{\circ}E$) < A ($N20{\sim}30^{\circ}E{\cdot}N10{\sim}20^{\circ}E$). Especially the forms of graph gradually transition from a uniform distribution to an exponential one. Lastly, the values of the six parameters for fault-segment length were divided into five groups. Among the six parameters, mean length and length of the longest fault segment decrease in the order of group III ($N10^{\circ}W{\sim}N20^{\circ}E$) > IV ($N20{\sim}60^{\circ}E$) > II ($N10{\sim}60^{\circ}W$) > I ($N60{\sim}90^{\circ}W$) > V ($N60{\sim}90^{\circ}E$). Frequency, longest length, total length, mean length and density of fault segments, belonging to group V, show the lowest values. The above order of arrangement among five groups suggests the interrelationship with the relative formation ages of fault segments.

• The Journal of Engineering Geology
• /
• v.8 no.2
• /
• pp.99-114
• /
• 1998

The Yangsan fault system of Kyungsang Basin in the southeastern part of Korean peninsula is one of the most important structures in the peninsula. A number of strong earthquakes occurred in the vicinity of the fault. It was suggested that this fault can be divided into three segments: northern, central and southern ones. Earthquake data around the Yangsan fault were classified into two groups as incomplete and complete ones; the former is the data before the Choseon Dynasty and the latter is those since the dynasty. The maximum likelihood method was applied to compute seismicity parameters such as earthquake occurrence rates, b-values of frequency-magnitude relation and maximum possible magnitudes for each segment and the entire fault. These parameters show considerably different values from segment to segment. The b-value for the entire fault turned out to be 0.85 and maximum possible magnitudes for the northern, central and southern segments are 5.2, 6.8 and 6.0, respectively. The mean return periods for the maximum possible magnitudes for each segments are greater than 1000 years. In addition, according to the analysis of the frequency-magnitude relation, the occurrence pattern of earthquakes around the Yangsan fault show more similarity to the characteristic earthquake model than the Gutenberg-Richter model. The data for each segments are, however, too scarce to obtain any physically meaningful results.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 2006.03a
• /
• pp.78-85
• /
• 2006

The Ulsan Fault System continues from north of Gyeongju to Ulsan city, trending NNW-SSE and is about 50 km. Many Quaternary faults have been reported and investigated with outcrop observation. Lineaments have been extracted with aerial photograph interpretation and classified by their ranks. Trench excavations on the lineaments along Ulsan Fault System have been carried out to clarify the neotectonic movements and fault parameters such as the latest movement age, fault displacement, slip rate and recurrence interval. We have compiled data from previous studies on criteria of segment type such as lineament rank, seismicity, slip rate, and the latest fault movement. Based on these data, we tried to devide the Ulsan Fault System into several segments. The results of segmentation with each types of segment along the Ulsan Fault System did not show singular division point but overlapped or different length and location.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.12 no.20
• /
• pp.1-24
• /
• 1989

This paper takes aim at the reliability evaluation by application of Fault Tree Analysis and its computerization. FTA is one of the methods for evaluation of system reliability and safety analysis. The important characteristic of this paper is that computer program is written in the package program(dBaseIII+) by 16Bit/AT personal computer. The program consists of three program segments. (1) The minimal cut sets of the system fault tree are obtained by means of "Fault tree reduction algorithm" (2) The minimal path sets are obtained by inversion of the minimal cut sets determined from fault tree (3) The importance of the basic events which are presented in the minimal cut sets is obtained by means of structural importance analysis. In this paper, a Fault Tree Analysis is applied to a BAG FILTER which is a kind of dust collector.collector.

• Proceedings of the KSEEG Conference
• /
• 2000.04a
• /
• pp.105-106
• /
• 2000

• Journal of The Geomorphological Association of Korea
• /
• v.26 no.1
• /
• pp.93-106
• /
• 2019

The Yangsan Fault is one of the main fault systems in the Korean peninsula. It can be divided into three segments (northern, central, and southern) by its paleoseismic and structural geologic properties. Based on the geomorphic features of the northern segment, which includes the Yugye Fault, we identified deflected streams as a geomorphic marker of strike-slip component of the fault, and knickpoints along the streams as evidence of dip-slip component of the fault. Geomorphic analyses showed that (1) the horizontal displacements of deflected streams decreased and (2) the retreat amounts of knickpoints tend to increased toward north along the lineament. We interpreted the variations caused by strain partitioning; that is, there might be some increases of the vertical component toward north, whereas the main strike-slip fault system dies out, splaying into horsetail structure toward north. Based on the response time of the landforms, these interpretations imply that (1) there were differences between horizontal slip rate and vertical slip rate along strike, and/or (2) there were different timings between horizontal and vertical deformations by fault.

• Computers and Concrete
• /
• v.29 no.2
• /
• pp.69-79
• /
• 2022

For long underground box utility tunnels, post-tensioned precast concrete is often used. Between precast tunnel segments, sealed waterproof flexible joints are often specified. Fault displacement can lead to excessive deformation of the joints, which can lead to reduction in waterproofing due to diminished contact pressure between the sealant strip and the tunnel segment. This paper authenticates utilization of a finite element model for a prefabricated tunnel fault-crossing founded on ABAQUS software. In addition, material parameter selection, contact setting and boundary condition are reviewed. Analyzed under normal fault action are: the influence of fault displacement; buried depth; soil friction coefficient, and angle of crossing at the fault plane. In addition, distribution characteristics of the utility tunnel structure for vertical and longitudinal/horizontal relative displacement at segmented interface for the top and bottom slab are analyzed. It is found that the effect of increase in fault displacement on the splice joint deformation is significant, whereas the effects of changes in burial depth, pipe-soil friction coefficient and fault-crossing angle on the overall tunnel and joint deformations were not so significant.