• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.759-764
• /
• 1997

In this study, Fatigue behavior of laser weldment in heterogeneous materials was investigated. Fatigue strength test and fatigue crack propagation test were performed for specimens with laser weldment in heterogeneous materials, and hardness test was performed. From the fatigue strength test. it was observed that the difference of strength between heterogeneous materials had eflect on crack initiation position and fatigue limit. From the fatigue crack propagation test. it was observed that fatigue behavior of laser weldment in heterogeneous materials is different from that in same materials. The difference of strength between heterogeneous materials and laser weldment had effect on fatigue crack propagation rate.

• 대한기계학회논문집
• /
• 제7권4호
• /
• pp.355-360
• /
• 1983

This paper deals with fatigue behavior of ion-nitrided coil spring. It is found that fatigue limit can be significantly increased by ion-nitriding. Ion-nitribed specimen which is treated at 550.deg. C for 5 hours improves in the fatigue limit by 30 percent in comparison with that of non-nitrided specimen. On the other hand, the value of spring constant K has nothing to do with nitriding time and temperature in this experimental range. Besides fatigue behavior, the following effects are discussed such as compound layer, diffusion layer, hardness distribution and their relations.

• 대한기계학회논문집
• /
• 제12권2호
• /
• pp.278-285
• /
• 1988

본 연구에서는 SM15C재와 SM35C재에 퍼얼라이트, 페라이트 조직의 영향을 배재한 비교적 균질한 조직인 구상화시멘타이트조직과 SM35C재에 실용조직 이면서 비교적 균질한 조직인 마르텐사이트 조직을 만들고, 가공하였다.

• 한국정밀공학회지
• /
• 제19권12호
• /
• pp.127-133
• /
• 2002

The objective of this study is to investigate fatigue life and fatigue crack propagation behavior The experiment of fatigue life for MMC have been carried out for the stress ratio R＝0.1 at 20Hz. Fatigue lift limit of AC4CH alloy is about 70 ㎫ and Fatigue limit of MMC has been increment to 120 ㎫, therefore, fatigue limits of MMC is about 71 % higher than that of AC4CH alloy Crack propagation tests on half-size CT specimen of thickness 12.5mm were conducted by using sinusoidal waveform. The crack length was monitored by compliance method. Test conditions were at 0.1 and 0.05 of load ratio at 10Hz of loading frequency and test load was 2.3kN. The effects of stress ratio on the fatigue crack propagation behavior for MMC was discussed within the Paris law. As the results of this study, Fatigue crack propagation increased with increasing the load ratio.

• 대한기계학회논문집A
• /
• 제40권8호
• /
• pp.751-757
• /
• 2016

본 논문은 스테어케이스법을 사용하여 크랭크 스로 부품용 S34MnV강의 피로한도의 신뢰도를 평가하는 것이다. 크랭크 스로 부품의 소재는 S34MnV이며, 뜨임 및 풀림 열처리된 단조강이다. 본 연구에서는 설계피로강도의 신뢰도를 예측하기 위해 축 하중 일정진폭 피로시험을 수행하였다. 시험편은 평균응력 0 MPa의 동일한 응력부하를 적용하였고, 즉 응력비는 -1로 하였다. 피로시험 결과는 Dixon-Mood 접근법으로 평가하였다. 스테어케이스법에 의해 예측된 피로강도의 평균과 표준편차는 각각 296.3 MPa 및 10.6 MPa로 나타났다. 마지막으로 어떤 임의의 파손 확률에 대한 피로강도의 신뢰도를 예측하였다. 본 연구에서 제안한 예측법은 단조강의 설계 최적화를 위한 피로강도 값을 결정할 수 있다.

• Journal of Welding and Joining
• /
• 제26권3호
• /
• pp.45-50
• /
• 2008

SM45C steel rods being used generally for power transmission shafts and machine components was selected and welded by Butt-GMAW(Gas Metal Arc Welding) method. An estimation of fatigue life was studied by constructing S-N curve. Fatigue strength of base metal zone showed higher values than one of weld zone in low cycles between $10^4$ and $10^6$cycles. However, significant decrease in fatigue strength of base metal was found around $10^6$cycles, which were almost same as one of heat affected zone. This decrease was attributed that initial residual stress of the steel rods distributed by drawing process was diminished by continually applied load, and resulted in softening of base metal. The fatigue limit of the weld zone was highest in the boundary between deposited metal zone and heat affected zone, and followed by in the order of deposited metal zone, base metal zone, and heat affected zone. Based on these results, it is revealed that the stress for safety design of machine components using SM45C butt-welded steel rods must be selected within the region of the lowest fatigue limit of heat affected zone.

• 대한기계학회논문집A
• /
• 제23권11호
• /
• pp.1922-1928
• /
• 1999

Rotary bending fatigue tests were carried out to investigate the influence of artificial defects on fatigue limit in annealed and austempered ductile iron. Obtained main results are as follows : (1) Artificial defect(micro hole type, dia.<0.4 mm) on specimen surface did not bring about a obvious reduction of fatigue limit in austempered ductile iron(ADI) as compared with annealed ductile iron. (2) According to the investigation of $\sqrt{area}_c$ which is the critical defect size to crack initiation at artificial defect, $\sqrt{area}_c$ of ADI is larger than that of annealed ductile iron. This shows that the situation of crack initiation at artificial defect in ADI is more difficult in comparison with annealed ductile iron. (3) One of the reasons for the low rate of crack initiation from artificial defect in ADI is that the resistance of matrix to crack initiation is higher than that of annealed ductile iron. (4) In case that the $\sqrt{area}$ of artificial defect and graphite nodule is the same, the rate of crack initiation from graphite nodule is higher than that from artificial defect. This reason is that the serious ruggedness around graphite nodule is formed by austempering treatment.

• 한국공작기계학회논문집
• /
• 제12권1호
• /
• pp.38-44
• /
• 2003

In this study, endurance limit and fatigue behavior of load carrying fillet welded cruciform joints depending on commonly used welding methods such as SMAW, SAW, MIG and FCAW are investigated. In respect of endurance limit SMAW specimen showes highest result, and then MIG, SAW, FCAW in descending order. However, SMAW specimen showes lowest crack growth rate and it followed by MIG, FCAW, SAW. By these results, it is needed to use SMAW or MIG welding methods for welding structures with small welding capacity and SAW or FCAW methods for large welding structures with respect to economic benefits and operation efficiency of welding. It was also shown fatigue crack growth rate was more influenced by the strenght of welding materials than the endurance limit of welding materials.

• 대한의용생체공학회:의공학회지
• /
• 제34권1호
• /
• pp.1-7
• /
• 2013

According to the frequent use of mobile devices, risk of repetitive strain injury for the finger joints was increasing recently. The purpose of this study was to investigate the difference of muscular endurance limit of the thumb between adults and children. A total of thirty subjects (15 adults: $41.0{\pm}7.9$ years and 15 children: $9.5{\pm}2.7$ years) was recruited for this experiment. Maximum voluntary contraction (MVC) of the thumb was measured for 100 trials for each subject by using a push-pull gauge. From the maximum peak value obtained, three main factors (MVC, endurance limit, and fatigue index) were defined to quantify fatigue characteristics of the thumb flexor muscle. The experimental results showed that the mean of MVC, endurance limit, and fatigue index of the children were approximately 50% compared to the adults (p < 0.001). From the results of Pearson correlation test, the endurance limit was highly correlated with weight, age, hand length rather than height. Based on this study, children are more vulnerable to repetitive task using the thumb such as text/SNS messaging, gaming, and scrolling.

• 대한조선학회지
• /
• 제9권2호
• /
• pp.33-42
• /
• 1972

This paper was studied on the behavior, crack formation and propagation of slip bands on low carbon steel which was heat-treated in three conditions in order to change metallic structure. The specimens were tested by rotating bending fatigue testing machine and also observed the variations of grains by microscope. From the test results it was clear that fatigue endurance limit and life of low carbon steel were more increased in contrast with the case that the grain size of specimen was more decreased. Slip bands developed at oil-quenched specimen and furnace-cooled specimen. Formed cracks in the first one or two grains below the surface were approximately "planar" type, there after they followed "wavy" type. It was also found that cracks at 30% higher stress than fatigue limit were usually developed inter-granular, and cracks at 12% higher stress than fatigue limit were propagated meandering path, partly trans- and partly inter-grandular.