• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.12
• /
• pp.109-119
• /
• 2002

In this paper, mechanism design of optical pickup actuator for fast access is proposed. This actuator is composed of moving magnet type actuator and moving coil type actuator for tracking and fine motion, respectively. Moving magnet type tracking actuator is configurated by two permanent magnets and four air-core solenoids. Additional damper by induced current in tracking actuator can reduce the transient vibration between the coarse seeking servo and fine seeking servo. Variable stiffness can be acquired by applying current to air-core solenoid simply. This actuator can achieve fast access by these additional damper and stiffness. Performance of this actuator is predicted through the FEM, simulation and simple experiment. Settling time for transient vibration is reduced to 14.7% according to simulation result.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.9 no.8
• /
• pp.3068-3078
• /
• 2015

Although the massive MIMO system supports a high throughput, it requires a lot of channel information for channel compensation. For the reduction of overhead, the massive MIMO system generally uses TDD as duplexing scheme. Therefore, the massive MIMO system is sensitive to rapidly changing fast fading in according to time. For the improvement of reduced SINR by fast fading, the adaptive power control is proposed. Unlike the conventional scheme, the proposed scheme considers mobility of device for adaptive power control. The simulation of the proposed scheme is performed with consideration for mobility of device. The result of the simulation shows that the proposed scheme improves SINR. Since SINR is decreased in according to the number of device in the network by unit of cell, each base station can accommodate more devices by the proposed scheme. Also, because the massive MIMO system with high SINR can use high order modulation scheme, it can support higher throughput.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.939-942
• /
• 2004

In this study, we report simulation results of single-panel LCOS (liquid crystal on silicon). Reflective LCOS microdisplays are widely used in various projection and near-eye application. For one panel system, liquid crystal response time is an important variable. The panel must switch fast enough to support the display of Field color sequential with high field rates. In order to have fast response and good contrast, a vertical alignment (VA) cell was used in this study. With suitable selection on LC parameters like temperature, viscosity, elastic constant and birefringence, it is possible to get response time of around 2ms from a 2.0 um-thick vertical alignment cell. This result also indicates an ease of production control on 2.0 um cells than 1.0 um cells.

• Proceedings of the Korea Society for Simulation Conference
• /
• 1999.04a
• /
• pp.60-64
• /
• 1999

Recently in manufacturing environment, manufacturing order is characterized by unstable market demand, shorter product life cycle, a variety of product and shorter production lead time. In order to adapt this manufacturing order, flexible manufacturing system(FMS) in manufacturing technology advances into the direction that machines become further versatile functionally and that tools are controlled by fast tool delivery device. Unlike conventional FMS to mainly focus on part flow, it is important to control tool flow in single-stage multimachine systems(SSMS), consisting of versatile machines and fast tool delivery device. In this paper, in SSMS under dynamic tool allocation strategy to share tools among machines, we propose real-time part release and tool allocation algorithms which can apply real factory and which can improve system performance.

• Journal of Information Processing Systems
• /
• v.18 no.6
• /
• pp.770-783
• /
• 2022

Early evacuations reduce the damage caused by catastrophic events such as terrorism, tsunamis, heavy rains, landslides, and river floods. However, even when warnings are issued, people do not easily evacuate during these events. To shorten the evacuation time, initiative-evacuation and its executors, initiative evacuees, are crucial in inducing other evacuations. The initiative evacuees take the initiative in evacuating and call out to their surroundings. This paper proposes a fast method to induce initiative-evacuation based on social graphs. The candidates are determined in descending order of the number of links for each person. The proposed method was evaluated through simulations. The simulation results showed a significant reduction in evacuation time.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.30A no.8
• /
• pp.11-18
• /
• 1993

In a spread spectrum system, the bandwidth and period of spreading code is wide and long, respectively. So it is necessary to make the code acquisition time as short as possible. In particular, serial search code acquisition system requires optimum dwell time for fast acquisition. In this paper, code acquisition time is calculated by varying dwell time. Among them, minimum code acquisition time is chosen and then optimum dwell time can be obtained. Detection probability (P$_{D}$) and false alarm probability (P$_{FA}$) can be obtained by integrating chi-square pdf by numerical analysis. The results are compared with that of gaussian approximation method and then it is concluded gaussian approximation method is not suitable for obtaining optimum dwell time. Computer simulation supports theoretical results.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.10C
• /
• pp.992-998
• /
• 2005

In this paper, An Ultra Fast Acquisition Algorithm of low transmission rate ultra-wideband(UWB) systems for car positioning and traffic light controling is proposed. Since the acquisition algorithms for CDMA system are not fast enough to access the low transmission rate UWB systems, the new ultra fast acquisition scheme which can be implemented with low cost and simplified circuit is required. The proposed algorithm adopted the Recurrent Sequential Estimation scheme and trinomial M-sequence. Therefore, The proposed scheme can reduce the average acquisition time in $1\~3{\mu}sec$ with simple circuit, even for the UWB systems which use long pseudo-noise(PN) sequence and transmit low power below the FCC EIRP emission limits. The simulation results for the average acquisition time of the proposed scheme are compared with the ones of the existing acquisition schemes.

• Journal of Electrical Engineering and Technology
• /
• v.6 no.5
• /
• pp.658-665
• /
• 2011

In the present paper, a novel fast peak detector for single- or three-phase unsymmetrical voltage sags is proposed. The proposed detector is modified from a single-phase digital phase-locked loop based on a d-q transformation using an all-pass filter (APF). APF generates a virtual phase with $90^{\circ}$ phase delay. However, this virtual phase cannot reflect a sudden change of the grid voltage in the moment of voltage sag, which causes a peak value to be significantly distorted and to settle down slowly. Specifically, the settling time of the peak value is too long when voltage sag occurs around a zero crossing, such as phase $0^{\circ}$ and $180^{\circ}$. This paper describes the operating principle of the APF problem and proposes a modified all-pass filter (MAPF) to mitigate the inherent APF problem. In addition, a new fast peak detector using MAPF is proposed. The proposed detector is able to calculate a peak value within 0.5 ms, even when voltage sag occurs around zero crossing. The proposed fast peak detector is compared with the conventional detector using APF. Results show that the proposed detector has faster detection time in the whole phase range. Furthermore, the proposed fast peak detector can be effectively applied to unsymmetrical three-phase voltage sags. Simulation and experimental results verify the advantages of the proposed detector and MAPF.

• Proceedings of the KSRS Conference
• /
• 2005.10a
• /
• pp.729-732
• /
• 2005

This paper describes a time-spatial domain model for simulating raw data acquisition of space-borne SAR system. The position, velocity and attitude information of the platform at a certain time instance is used for deriving sensor-target model. Ground target is modelled by a set of point scatters with reflectivity and two-dimensional ground coordinates. The signal received by SAR is calculated for each slow and fast time instance by integrating the reflectivity and phase values from all target point scatters. Different from frequency domain simulation algorithms, the proposed time domain algorithm can provide fully physical modelling of SAR raw data simulation without any assumptions or approximations.

• Journal of Power Electronics
• /
• v.10 no.6
• /
• pp.739-748
• /
• 2010

The increased integration of fuel cells with power electronics, critical loads, and control systems has prompted recent interest in accurate electrical terminal models of the polymer electrolyte membrane (PEM) fuel cell. Advancement in computing technologies, particularly parallel computation techniques and various real-time simulation tools have allowed the prototyping of novel apparatus to be investigated in a virtual system under a wide range of realistic conditions repeatedly, safely, and economically. This paper builds upon both advancements and provides a means of optimized model construction boosting computation speeds for a fuel cell model on a real-time simulator which can be used in a power hardware-in-the-loop (PHIL) application. Significant improvement in computation time has been achieved. The effectiveness of the proposed model developed on Opal RT's RT-Lab Matlab/Simulink based real-time engineering simulator is verified using experimental results from a Ballard Nexa fuel cell system.