• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.5
• /
• pp.910-923
• /
• 1992

Experimental verification of numerical results is conducted by measuring the dynamic strains of mid-points of the coupler and the lever for the 4-bar linkage mechanism with rigid bearing and flexible bearing, respectively. For the axial strain of lever mid-point, the numerical results including geometric stiffness almost agree with the experimental ones, however, the numerical results excluding geometric stiffness almost agree with the experimental ones for the axial strain of coupler mid-point. It is supposed that these phenomena should be caused by the fact that the motion of the coupler is more complicated than of the lever. The signals of dynamic strains of coupler and lever mid-points, measured by strain gages, are transformed into frequency domain by fast fourier transformer. From this experiment, the lst resonance frequencies of the coupler and the lever are obtained. It is made clear that the former almost agrees with the fundamental and the latter the 2nd mode natural frequency of the mechanism system calculated by numerical analysis.

• Journal of Korea Society of Digital Industry and Information Management
• /
• v.14 no.4
• /
• pp.79-85
• /
• 2018

This paper presents an implementation method of Long Term Evolution-Advanced (LTE-A) Physical Downlink Shared Channel (PDSCH) decoder using a general-purpose multicore Digital Signal Processor (DSP), TMS320C6670. Although the DSP provides some useful coprocessors such as turbo decoder, fast Fourier transformer, Viterbi Coprocessor, Bit Rate Coprocessor etc., it is specific to the base station platform implementation not the mobile terminal platform implementation. This paper shows an implementation method of the LTE-A PDSCH decoder using programmable DSP cores as well as the coprocessors of Fast Fourier Transformer and turbo decoder. First, it uses the coprocessor supported by the TMS320C6670, which can be used for PDSCH implementation. Second, we propose a core programming method using DSP optimization method for block diagram of PDSCH that can not use coprocessor. Through the implementation, we have verified a real-time decoding feasibility for the LTE-A downlink physical channel using test vectors which have been generated from LTE-A Reference Measurement Channel (RMC) Waveform R.6.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.14 no.3
• /
• pp.97-106
• /
• 2000

This paper proposes on-line based a deterioration diagnosis device for diagnosis pole transformers using tan$\delta$ and FFT(fast Fourier transform). We measured tan$\delta$ and temperature to diagnose pole transformer insulating oil, diagnostic results are processed by FFT. For measuring convenience, we use R/F(radio frequency) wireless data communication module operating by secondary voltage of pole transformer. We have voltage variation test and oil temperature variation test to prove usability of proposed diagnosis device. The result of this paper shows that the proposed device can be used as deterioration diagnosis device of pole transformers.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2002.11a
• /
• pp.835-838
• /
• 2002

A running high voltage equipments produce ultrasonic wave that has unique sound by the specific characteristics of the electricity. The generation of the ultrasonic wave is made by the electric transform like arcing, corona, and tracking so on. The mechanical losses and fatal human damages are happened by the electric failure of high voltage equipments. To prevent and diagnose the obstacle factors of the high voltage equipments, the measurement of the ultrasonic wave became to be prominent. However standardized data have been a deficient situation by now. This paper measures the ultrasonic wave coming from the real running transformer equipments and transforms it as an audio frequency. Measured data represents as frequency and time domain through the FFT(Fast Fourier Transform) transform. In conclusion, the purpose of this paper is to standardize the analyzed data.

• Proceedings of the KIEE Conference
• /
• 2000.07c
• /
• pp.1936-1938
• /
• 2000

In this paper, a frequency spectra of AE (acoustic emission) signals detected from the partial discharges of an epoxy resin void and a cast resin transformer in operating were analyzed to offer the proper frequency range of AE signals from the corona discharge for the purpose of AE sensor selection, From these results, a frequency spectra of AE signals emitted from the corona discharges in the void of an epoxy resin sample were about 190[kHz] to 220[kHz] by the FFT(fast fourier transform), A frequency spectra of AE signals emitted from a cast. resin transformer with non-load were appeared to be downward of about 140[kHz] by the FFT, and then a frequency spectra of AE signals emitted from the above of cast resin transformer with load were appeared to increase from about 190[kHz] to 220[kHz] by the FFT.

• Journal of Korea Society of Digital Industry and Information Management
• /
• v.15 no.4
• /
• pp.85-92
• /
• 2019

This paper presents a SDR-based Long Term Evolution Advanced (LTE-A) Physical Downlink Shared Channel (PDSCH) decoder using a multicore Digital Signal Processor (DSP). For decoder implementation, multicore DSP TMS320C6670 is used, which provides various hardware accelerators such as turbo decoder, fast Fourier transformer and Bit Rate Coprocessors. The TMS320C6670 is a DSP specialized in implementing base station platforms and is not an optimized platform for implementing mobile terminal platform. Accordingly, in this paper, the hardware accelerator was changed to the terminal implementation to implement the LTE-A PDSCH decoder supporting the multi-antenna and the functions not provided by the hardware accelerator were implemented through core programming. Also pipeline using multicore was implemented to meet the transmission time interval. To confirm the feasibility of the proposed implementation, we verified the real-time decoding capability of the PDSCH decoder implemented using the LTE-A Reference Measurement Channel (RMC) waveform about transmission mode 2 and 3.

• Proceedings of the KIEE Conference
• /
• 1998.07c
• /
• pp.1082-1084
• /
• 1998

In this paper, we developed a diagnosis device for ZnO arrester to detect on-line leakage current and acquire data from the power distribution system. The arrester is important power equipment used in power transmission and distribution systems to protect the generator and the main transformer from surge and overvoltage. First of all we developed a diagnosis device for ZnO arrester leakage current. And then we detect the total leakage current by the developed device without disconnecting the arrester ground wire and analysis the 3rd order harmonic by Fast Fourier Transform(FFT) to diagnose the ZnO arrester deterioration. With measuring the total current and the resistive current of power distribution system in operation, we analysis the trend of resistive current component in the total leakage current. We expect the result will be promote the method to protect electrical utility and customer from accident.