• International Journal of Fluid Machinery and Systems
• /
• 제2권4호
• /
• pp.449-455
• /
• 2009

A reversible axial flow fan called jet fan has been widely used for longitudinal ventilation in road tunnels to secure a safe and comfortable environment cost-effectively. As shifting the flow direction is usually made by only switching the rotational direction of an electric motor due to heavy duty, rotor blades having identical aerodynamic performance for bidirectional flow should be necessary. However, such aerodynamically desirable blades haven't been developed sufficiently, since most of the related studies have been done from the viewpoint of unidirectional flow. In the present paper, we demonstrate a method to profile the blade section suitable for bidirectional flow, which is validated by studying the aerodynamic performances of rotor blades of a two-stage jet fan experimentally and numerically.

• 설비공학논문집
• /
• 제26권2호
• /
• pp.67-71
• /
• 2014

In this study, a fan coil unit with an oval-type heat exchanger has been developed. The performance of the present fan coil unit has been investigated, by comparison with the previous fan coil unit with a circular-type heat exchanger. For the fan coil unit with circular- and oval-type heat exchangers, the heat flux and pressure loss through the heat exchangers were measured at standard operating conditions. In addition, the wind speeds exhausted from the fan coil units were compared, for the same fan motor operation. The experimental results show that the average wind speed of the oval-type heat exchanger is 20 percent higher than that of the circular-type heat exchanger. The heat flux in the oval-type heat exchanger is enhanced by 40% or more, over the circular-type heat exchanger.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.120-122
• /
• 2004

In this Paper, high efficiency dual air-gap induction motor with permanent magnet rotor is described. The finite element method is used to design the rotor and magnet. And we presented the analysis, construction, experimental results of prototype single phase induction motor with permanent magnet rotor for air-conditioner fan motor.

• 한국유체기계학회 논문집
• /
• 제10권6호
• /
• pp.7-16
• /
• 2007

An axial-type fan which operates at the relative total pressure of 671Pa and static pressure of 560Pa with the flow rate of $416.6m^3/min$ is developed with an optimization technique based on the gradient method. Prior to the optimization of fan blade, a three-dimensional axial-type fan blade is designed based on the free-vortex method along the radial direction. Twelve design variables are applied to the optimization of the rotor blade, and one design variable is selected for optimizing a stator which is located behind of the rotor and is used to support a fan driving motor. The total and static pressure are applied to the restriction condition with the operating flowrate on the design point, and the efficiency is chosen as the response variable to be maximized. Through these procedures, an initial axial-fan blade designed by the free vortex method is modified to increase the efficiency with the satisfaction of the operating condition. The optimized fan is tested to compare the aerodynamic performance with an imported same class fan. The test result shows that the optimized fan operates with the satisfaction of restriction conditions, but the imported fan cannot. From the experimental and numerical test, they show that this optimization method improves the fan efficiency and operating pressures of a fan designed by the classical fan design method.

• 전력전자학회지
• /
• 제8권2호
• /
• pp.36-42
• /
• 2003

• 한국정보통신학회논문지
• /
• 제7권4호
• /
• pp.812-818
• /
• 2003

산업용 및 공조용 팬 동력원의 대부분이 농형 유도전동기를 사용하고 있으며 그 구조는 외측 고정자에 의해 내측 회전자가 회전하는 형태이다. 이와는 반대로 내측 고정자에 의해 외측 회전자가 구동되는 외측 회전형 방식의 유도전동기는 적은 전류로 지속적인 큰 토크가 필요한 펀 둥에 적합한 형태라고 할 수 있다. 즉, 외측이 회전함으로써 큰 관성력을 얻을 수 있으므로, 일단 회전하게 되면 큰 토크를 지속적으로 발생시킬 수 있다. 그리고, 일시적인 입력 전압의 변동이나 부하 변동시에도 외측 회전자의 큰 관성력에 힘입어 송풍량을 고르게 해주는 역할을 할 수 있으리라 사료된다. 본 논문에서는 팬 또는 이와 유사한 특성을 가진 부하의 동력원으로 사용할 목적으로, 외측 회전형 유도 전동기의 회전자를 설계, 제작하여 고정자 저항시험, 무부하시험 및 회전자 구속시험을 통해 등가회로 정수를 측정하였다. 그리고, 부하시험을 행하여 얻은 토크-속도, 출력, 역률 및 효율 특성곡선을 분석함으로써 외측회전형 유도전동기 개발과 관련된 기술적인 토대를 마련하고자 한다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 춘계학술대회논문집
• /
• pp.764-769
• /
• 2004

The DC Motor in a vehicle may cause noise and vibration because of high speed revolution, which can make a driver feel uncomfortable. There have been various studies attempting to solve these problems, focusing mostly on the causes of and ways to reduce noise and vibration. It is suggested that the noise in a DC Motor may be primarily due to interaction between a brush and a commutator. Brush noise, the most common noise in a DC Motor, results from a brush bounced from the surface of the commutator, fluctuation of the friction between the brush and the commutator, and the impact on the brush when passing over slots of the commutator. Based on the noise test, one of the most important design parameters was shown to be the roundness of the commutator. As the DC motor is used, the roundness of the commutator gets bigger with subsequent increase of the level of brush noise and vibration. There must be a threshold in order to prevent the brush noise from getting worse. Using the method of CAE is more efficient than the real test for purposes of looking for various design parameters to maintain the roundness of the commutator. In this study, the design process to reduce the brush noise is presented with the use of a computer model. The design parameters to reduce the brush noise and vibration are proposed by using FEM. The design parameters are used to reduce the noise and vibration of a DC motor and it is verified with the test results on a fan DC motor in a vehicle. This method may be applicable to various DC motors.

• 한국전자통신학회논문지
• /
• 제13권4호
• /
• pp.757-764
• /
• 2018

본 논문은 공조시스템에 사용되는 1마력급 2상 BLDC 팬모터의 설계 및 구현에 관하여 기술한다. 본 연구에서 구현한 BLDC 모터는 수명 및 내구성이 우수한 무정류자 모터방식이며 2상 전원에 의해 구동된다. 공조시스템에 사용되는 모터의 가장 중요한 목표사양은 정격운전점에서 높은 효율을 갖는 것이다. 이를 위해 BLDC 모터의 고정자 형상과 회전자 자석의 설계를 수행하고 구동을 위한 제어회로를 설계하였다. BLDC 모터는 모터부와 제어부 그리고 전원부가 일체화된 구조를 갖는다. BLDC 모터의 특성계산을 위해 유한요소해석을 사용하였으며 시제품의 제작 및 성능시험을 실시하여 설계결과의 적합성을 확인하였다.

• 대한기계학회논문집B
• /
• 제25권10호
• /
• pp.1281-1292
• /
• 2001

Experiments were done for the comparison of performance and flow characteristics between a two -stage axial flow fan and a counter-rotating axial flow fan. Each stage of the two -stage axial flow fan used fur the present study has an eight bladed rotor and thirteen slater blades. The front and the rear rotor of the counter - rotating axial flow fan have eight blades each and are driven by coaxial counter ro latins shafts through a gearbox located between the rear rotor and the electric motor. Both of the two axial fan configurations have identical rotor blades and the same operating condition fur the one -to-one comparison of the two. Performance curves of the two configurations were obtained and compared by varying the blade pitch angles and axial gaps between the blade rows. The fan characteristic curves were obtained following the Korean Standard Testing Methods for Turbo Fans and Blowers (KS B 6311). The fa n flow characteristics were measured using a five-hole probe by a non-nulling method. The velocity profiles between the hub and tip of the fans were measured and analyzed at the particular operating condition s of peak efficiency, minimum and maximum pressure coefficients. The peak efficiency of the counter-rotating axial fan was improved about 2% respectively, compared with the two stage axial fan. At the minimum pressure coefficient point of the two stage axial fan, the fan inlet flow patterns show that axial velocity highly decreased in the vicinity of the blade tip region. Also, the reverse flow took place at the blade tip.

• 대한기계학회논문집B
• /
• 제22권6호
• /
• pp.849-859
• /
• 1998

The heat generated in an induction motor is mostly dissipated through the frame. The study on the heat transfer characteristics of a newly manufactured finless TEFC(Totally Enclosed Fan Cooled) induction motor showed/that it had an unsuitable structure in view of the heat transfer. The angle of the cooling air flow was very large and the ribs disturbed the air flow and partially generated the wake region on the frame. In the wake region the temperature was very high. Thus the heat transfer coefficients were lower than those of the frame with fins. Also was investigated the heat transfer characteristics of the motor frame by installing various guide vanes in the fan-side end cap. An optimum heat transfer case was found and the average heat transfer coefficient of the frame was 70% higher and the average coil temperature measured by the resistance method was 9 deg. C lower than that of the frame which had no guide vanes.