• 설비공학논문집
• /
• 제17권11호
• /
• pp.1035-1042
• /
• 2005

In the present study, the principle of minimum energy is employed to configure the shape of rivulet flowing down an inclined surface. The profile of laminar rivulet is determined by numerical integration. The maximum center thickness, which corresponds to the minimum thickness of falling film, is found to exist regardless of liquid flow rate and is compared with the analytical and experimental data. At small liquid flow rate the center thickness of rivulet and its width increase almost linearly with flow rate. Once the center thickness of rivulet becomes very close to its maximum value, its growth rate retards abruptly. However the width of rivulet increases proportionally to the liquid flow rate and most part of its free surface is as flat as that of stable film. The growth rate of rivulet thickness with respect to liquid flow rate becomes larger at bigger contact angle. The width of rivulet increases rapidly with its flow rate especially at small contact angle, As the liquid-vapor interfacial shear stress increases, the center thickness of rivulet decreases with its flow rate, which is remarkable at small contact angle. However the effect of interfacial shear stress on the width of rivulet is almost negligible.

• 대한기계학회논문집A
• /
• 제25권6호
• /
• pp.930-937
• /
• 2001

The friction and wear behavior of short carbon fiber reinforced polyetheretherketone was studied experimentally under dry sliding conditions against SCM440(AISI 4140) disks with different surface roughness and hardness at the low sliding speeds and the high pressures on a pin-on-disk apparatus. Under the low disk surface roughness value the earsplitting noise and stick-slip were occurred. The increased adhesion friction and wear factor with stick-slip made the friction and wear behavior worse. Under the high disk surface hardness the break and falling-off of carbon fibers were accelerated. The carbon fibers fallen off from the matrix were ground into powder between two wear surfaces and this phenomenon caused abrasive friction and wear factor to increase. So the friction and wear behavior became worse. With the transfer film made of wear particles formed on a disk, the carbon powder film formed on a pin lowered a friction coefficient.

• Journal of Chest Surgery
• /
• 제17권1호
• /
• pp.67-73
• /
• 1984

A 25 years old male patient with traumatic aneurysm of descending thoracic aorta was treated successfully. He was admitted due to blunt trauma to the chest wall as falling down into water. He has been treated with closed thoracotomy and close observation. After a month simple chest film showed abnormal mass shadow around the aortic knob. Aortogram revealed aneurysm of descending thoracic aorta. Aneurysm was resected and replaced with woven Dacron graft with aid of Gotts shunt. His postoperative course was uneventful.

• Journal of Advanced Marine Engineering and Technology
• /
• 제22권3호
• /
• pp.362-370
• /
• 1998

Absorption systems require a heat source for working but they have a great merit in that relatively low-temperature and low-quality types of thermal energy such as solar heat and exhaust heat can be effectively utilized as heat source. However details research related to absorbers which have a great effect on performances has been rarely done and thus there has been a strong hope for positive developments to improve their efficiencies. This paper describes absorption experiments made with different inside tube diameters and shapes. The purpose of this study is to acquire basic knowledge about heat and mass transfer in a falling film type absorber with vertical inner tubes. Heat and mass transfer were measured for water vapor absorption into a water/LiBr solution flowing down an absorber of vertical inner tubes. As a result absorption acceleration tube compares bare tube and heat transfer improved by order of insert spring tube corrugated tube grooved tube. And the acceleration that is good provided in inserting spring tube for both sides of heat and mass transfer.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2002년도 춘계학술대회논문집
• /
• pp.41-47
• /
• 2002

A model of simultaneous heat and mass transfer process in absorption of refrigerant vapor into a lithium bromide solution of water-cooled vertical plate absorber was developed. The model can predict temperature and concentration profiles as well as the absorption heat and mass fluxes, the total heat and mass transfer rates and the heat and mass transfer coefficients. Besides, the effect of operating condition on absorption mass flux has been investigated, with the result that the absorption mass flux is increased as the inlet cooling water temperature decreases, the system pressure increases and the inlet solution concentration increases. And among the effects of operating parameters on absorption mass flux, the effect of inlet solution concentration is dominant.

• Journal of Advanced Marine Engineering and Technology
• /
• 제28권2호
• /
• pp.243-251
• /
• 2004

Absorption chiller/heater can utilize the unused energy of the daily life waste heat, the industry waste heat. the solar energy and the earth energy. These can contribute to energy savings. But the absorption chiller/heater has a demerit that the size of absorption chiller/heater is larger than that of the vapor compression type based on same capacity. In this study. the experimental apparatus of an absorber is manufactured as a plate. which is newly applied in an absorber. The experimental apparatus is composed of a plate type absorber. which can increase the heat exchange area per unit volume and thus facilitating to deeply investigate more detail features instead of that done by the existing type. i.e.. horizontal tube bundle type. The characteristics of heat transfer and refrigeration capacity are studied experimentally. The absorption enhancement by using surfactant is closely examined through the experiment and comparative figures are presented in quantitative and qualitative analysis.

• 센서학회지
• /
• 제22권6호
• /
• pp.444-449
• /
• 2013

ZnO-based ethanol gas sensors were fabricated by the painting method and their electrical and ethanol gas sensing characteristics were investigated. The ZnO-Pt (1 wt.%) film heat treated at $400^{\circ}C$, for 2 hrs. in air showed the highest sensitivity to ethanol gas in air at an operating temperature of $250^{\circ}C$ The sensitivity of the gas sensors to 1000 ppm ethanol in air at $250^{\circ}C$ was 8.7 and rising time and falling time of the gas sensors were 3.12 minutes and 25 minutes, respectively.

• 설비공학논문집
• /
• 제11권5호
• /
• pp.570-578
• /
• 1999

An experimental study has been performed on heat and mass transfer in a falling film absorber with a strong lithium bromide solution in small-sized household absorption chiller/heater. Components were concentrically arranged in a cylindrical form. from the center, low temperature generator, absorber and evaporator. This arrangement of helical-typed heat exchangers allows to make the machine much more compact than conventional one. Experimental measurements were conducted with a helical absorber and the obtained data were compared with data in the literatures. The comparison revealed that the helical absorber tube provides a similar performance to existing tube bundle absorber in heat and mass transfer. As a result, the heat and mass transfer characteristics of helical type absorber showed the possibility of the reduction in size and weight of small] capacity absorption chiller/heater.

• 한국전기전자재료학회논문지
• /
• 제32권4호
• /
• pp.302-306
• /
• 2019

We investigated a solution-derived $Y_2O_3$ film treated by ion beam (IB) irradiation as a liquid crystal (LC) alignment layer. With IB irradiation, homogeneous LC alignment was achieved irrespective of the annealing temperature. To verify the effect of IB irradiation, we conducted surface analyses such as X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM). As $Y_2O_3$ is a high-k material, the electro-optical properties of the twisted nematic (TN) cells were superior to those of conventional TN cells based on a rubbed polymer, with an LC rising time of 4.1ms and falling time of 2.9ms. The IB-irradiated $Y_2O_3$ is a good alternative as an alignment layer for fast-switching TN LC displays.

• 한국산학기술학회논문지
• /
• 제16권10호
• /
• pp.7071-7077
• /
• 2015

최근 스마트폰, 태블릿 PC 및 전자기기 등의 사용이 증가함에 따라 커버글라스의 수요가 증가하고 있는 추세이다. 모바일 기기의 디스플레이가 대형화되면서 접촉이나 낙하 등과 같이 외부에서 힘을 받게 되는 환경에서 높은 강도를 유지하는 것이 요구되고 있다. 커버글라스 제작 공정에서 연마공정은 커버글라스의 표면거칠기 및 충분한 강도를 제공하는 중요한 공정이다. 기존 연삭 숫돌에 의한 가공방법은 커버글라스 가공표면에 스크레치, 칩핑, 노칭 및 마이크로 크랙 등의 가공 문제점이 발생한다. 따라서 본 연구에서는 모바일 커버글라스의 연마를 위해 연마필름을 이용한 폴리싱 시스템을 개발하였다. 구조적 안정성을 평가하기 위해 연마 필름 폴리싱 시스템에 대한 유한요소모델을 생성하였고 다물체 동역학 해석을 수행하였다. 연마 필름 폴리싱 시스템에 대한 응력 및 변위 해석을 통해 특성을 분석하였고 레이저 변위 센서를 이용해 제작된 시스템에 대한 변위를 측정하여 구조적 안정성에 대해 확인하였다.