• 한국가스학회지
• /
• 제16권4호
• /
• pp.8-15
• /
• 2012

GO-FLOW기법은 시스템이 정상적으로 작동할 가능성을 평가할 수 있는 기법으로써 신호선과 연산자를 사용하여 시스템을 GO-FLOW Chart로 모델화하고, 이 GO-FLOW Chart를 순차적으로 해석하여 시스템의 신뢰도를 평가하는 기법이다. 그러나 GO-FLOW기법은 1개의 시스템 구성요소를 여러 개의 연산자로 모델링하므로 시스템 흐름도와 상이한 GO-FLOW Chart가 작성될 수 있고, 시간점을 지정하여 시간을 모델링하므로 실제 운전시간에 따른 신뢰도 변화를 평가하기 어렵다. 따라서 본 연구에서는 구성요소의 기능(정상/고장)을 기준으로 시스템의 신뢰도를 평가하는 기법을 개발하였다. 본 기법은 구성요소의 운전상태와 상관없이 그 기능을 유지할 가능성을 기준으로 시스템의 신뢰도를 평가하며, 1개의 구성요소는 1개의 연산자로 모델링하므로 시스템 흐름도와 거의 유사한 모델도를 작성할 수 있고, 실제시간을 반영한 연산자를 사용하여 실제시간에 따른 시스템의 신뢰도를 쉽게 평가할 수 있다.

• Journal of Welding and Joining
• /
• 제28권2호
• /
• pp.66-73
• /
• 2010

Conventional fracture test of resistance spot weld had been performed without consideration of paint baking process in automobile manufacturing line. This study was aim to investigate the effect of paint baking on fracture mode and load carrying capacity in fracture test for resistance spot welded 780TRIP steels. With paint baking cycle after resistance spot welds, peel tests and microhardness were conducted on the as-welded and baked samples. Resistance spot welds in AHSS (Advanced High Strength Steels) are prone to display partial interfacial fractures during fracture test or vehicle crash. Baking cycle increased the load-carrying capacity of the resistance spot welded samples and improved the fracture appearance from partial to full button fracture for the L-type peel tests. Specially, the differences in fracture appearance are apparent when the nugget size of spot welds is small enough to produce the partial interfacial fracture. The comparison of macrohardness and microstructure between as-welded and baked samples showed that there are no large difference in change the fracture mode. However, the results of the instrumented indentation test suggested that fusion zone and HAZ of baked sample have less tensile and yield strength and proves that the tempering effects are applied and enhanced the resistance to fracture on welds with application of baking cycle.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2009년 추계학술발표대회
• /
• pp.95-95
• /
• 2009

Zinc coatings provide the most effective and economical way of protecting steel against corrosion. There are three types of galvanizing lines typically used in production line in galvanizing industries,Galvanize (GI) coating (Zn-0.1-0.3%Al), Galfan coating (Zn-5%Al), Galvalume(GL) coating (45%Zn-Al). In continuous Galvanizing lines, the immersed bath hardware (e.g. bearings, sink, stabilizer, and corrector rolls, and also support roll arms and snout tip) are subjected to corrosion and wear failure. Understanding the reaction of these materials with the molten Zn alloy is becomes scientific and commercial interest. To investigate the reaction with molten Zn alloys, static immersion test performed for 4, 8, 16, and 24 Hr. Two different baths used for the static immersion, which are molten Zn and molten Zn-55%Al. Microstructures characterization of each of the materials and intermetallic layer formed in the reaction zone was performed using optical microscope, SEM and EDS. The thickness of the reaction layer is examined using image analysis to determine the kinetics of the reaction. The phase dominated by two distinct phase which are eutectic carbide and matrix. The morphology of the intermetallic phase formed by molten Zn is discrete phase showing high dissolution of the material, and the intermetallic phase formed by Zn-55wt%Al is continuous. Aluminum reacts readily with the materials compare to Zinc, forming iron aluminide intermetallic layer ($Fe_2Al_5$) at the interface and leaving zinc behind.

• 대한금속재료학회지
• /
• 제49권12호
• /
• pp.967-976
• /
• 2011

Conventional fracture tests of resistance spot welds have been performed without consideration of the paint baking process in the automobile manufacturing line. The aim of this paper is to investigate the effect of the paint baking process on load carrying capacity and fracture mode for resistance spot welded 590 dual phase (DP), 780DP, 980DP, 590 transformation in duced plasticity (TRIP), 780TRIP and 1180 complex phase (CP) steels. With paint baking after resistance spot welding, the l-shape tensile test (LTT) and nano-indentation test were conducted on the as-welded and paint baked samples. Paint baking increased the load-carrying capacity of the resistance spot welded samples and improved the fracture appearance from partial interfacial fracture (PIF) to button fracture (BF). Improvement in fracture appearance after LTT is observed on weldments of 780 MPa grade TRIP steels, especially in the low welding current range with paint baking conditions. The higher carbon contents (or carbon equivalent) are attributed to the low weldability of the resistance spot welding of high strength steels. Improvement of the fracture mode and load carrying ability has been achieved with ferrite hardening and carbide formation during the paint baking process. The average nano-indentation hardness profile for each weld zone shows hardening of the base metal and softening of the heat affected zone (HAZ) and the weld metal, which proves that microstructural changes occur during low temperature heat treatment.

• 한국지형학회지
• /
• 제15권2호
• /
• pp.25-35
• /
• 2008

2006년 7월의 태풍 에위니아와 빌리스에 의한 집중호우로 인해 급경사의 사면이 많고 기복이 큰 강원도 지역에서 토사재해가 크게 발생하였다. 특히 한계령을 관통하는 국도 44호선 도로는 단층선곡을 따라 건설되어 토사재해의 가능성이 가장 높은 편에 속하는 지역이다. 오색천 주변에서 발생한 토석류는 호우에 의해 공극수압이 상승하고 사면부의 무게가 증가하면서 발생한 능선부와 산정부의 산사태에 의해 촉발되었다. 또한 기존의 붕적물 또는 계안퇴적물에 가해진 하천의 압력에 의해서도 특히 공격사면 쪽에서 많은 토석류가 발생하였다. 하천의 상류부에서는 도로주변의 급경사의 절개지와 사면부의 얇은 풍화층에서 산사태가 발생한 반면, 중류부에서는 계류부의 토석류가 도로변의 배수구조물 용량을 초과하여 월류가 발생하여 도로와 교량이 파괴되었고, 하류부에서는 하천범람에 의한 계류부 양안의 침식과 토석류에 의한 피해가 가장 크게 나타났다. 하류부 퇴적층의 경우 토석류가 일회성이 아니라 과거 수차례 더 발생했었다는 사실을 보여주고 있다. 따라서 기후변화와 관련하여 호우의 빈도와 강도가 높아질 것으로 예측되는 만큼 추후 토사재해와 관련된 정보시스템의 구축과 관리시스템에 대한 연구가 절실히 요구된다.

• 한국기계가공학회지
• /
• 제18권9호
• /
• pp.72-80
• /
• 2019

In this task, the tool dynamometer design and manufacture, and the Ansys S/W structural analysis program for tool attachment that satisfies the cutting force measurement requirements of the tool dynamometer system are used to determine the cutting force generated by metal cutting using 3-axis static structural analysis and the LabVIEW system. The cutting power in a cutting process using a milling tool for processing metals provides useful information for understanding the processing, optimization, tool status monitoring, and tool design. Thus, various methods of measuring cutting power have been proposed. The device consists of a strain-gauge-based sensor fitted to a new design force sensing element, which is then placed in a force reduction. The force-sensing element is designed as a symmetrical cross beam with four arms of a rectangular parallel line. Furthermore, data duplication is eliminated by the appropriate setting the strain gauge attachment position and the construction of a suitable Wheatstone full-bridge circuit. This device is intended for use with rotating spindles such as milling tools. Verification and machining tests were performed to determine the static and dynamic characteristics of the tool dynamometer. The verification tests were performed by analyzing the difference between strain data measured by weight and that derived by theoretical calculations. Processing test was performed by attaching a tool dynamometer to the MCT to analyze data generated by the measuring equipment during machining. To maintain high productivity and precision, the system monitors and suppresses process disturbances such as chatter vibration, imbalances, overload, collision, forced vibration due to tool failure, and excessive tool wear; additionally, a tool dynamometer with a high signal-to-noise ratio is provided.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2009년도 춘계학술대회
• /
• pp.580-583
• /
• 2009

철강 및 제조분야의 생산과 물류의 글로벌화를 위해 생산정보화 시스템에서 접근성 용이와 생산공정 라인의 변화와 시스템 확장에 따른 유지보수 비용의 최소화가 매우 중요하다. 따라서 본 논문에서는 시스템 간의 통합이나 업무 확장에 따른 유지보수 비용을 감소시키고 시스템 사용자의 접근성을 용이하게 하기 위해 객체지향의 디자인 패턴 기법 적용하여 설계하고 JSP를 이용하여 웹 기반 통합설계 관리 시스템을 구현한다. 아울러 제안된 MES 시스템은 세부적으로 설비마스터 코드관리, 설비관리, 점검관리, 수리관리, 고장관리, 통계관리 등의 다양한 기능을 제공하고 있다.

• STI Policy Review
• /
• 제5권2호
• /
• pp.1-19
• /
• 2014

The concept of a holistic innovation policy is defined in this article, with discussions of what it is, why it is relevant, and how it can be implemented to enhance product innovation. It is shown that the innovation systems approach has diffused rapidly during the latest decades and has completely replaced the linear view in the field of innovation research. The majority of European countries are striving in the direction of developing a more holistic innovation policy. However, it is concluded that the innovation policies in European countries are still dominantly linear despite the fact that holistic policy seems to be the driving vision. Innovation policy is behindhand. Why innovation policy is still linear is also preliminarily discussed. Policymakers attending conferences on innovation are practically always in favor of holistic (systemic, broad-based, comprehensive, etc) innovation policies, have abandoned the linear view by learning from innovation research. The division between "linear" and "holistic" seems to be located within the community where innovation policies are designed and implemented, a community composed of policymakers (administrators/bureaucrats) and elected politicians. Perhaps the dividing line is between these two groups in that politicians, who actually make the decisions, may still reflexively believe in the linear view. Nevertheless, there seems to be a failure in communication between researchers and politicians in the field of innovation and there is therefore a strong need to involve innovation researchers in policy design and implementation to a much higher degree. Another way to increase the degree of holism could be to separate innovation policy from research policy, since their integration tends to cement the linear character of innovation policy. The empirical results are based on a questionnaire sent to twenty-three EU Member States, out of which nineteen (83%) responded. Part of the work for this article was carried out for the European Research and Innovation Area Committee (ERAC) of the European Commission (DG RTD).

• 한국항행학회논문지
• /
• 제25권5호
• /
• pp.415-425
• /
• 2021

금융권은 디지털 전환 흐름에 맞춰 새로운 기술로 금융서비스를 제공하고 있다. 그 중 전세계 금융업계의 관심을 주목받고 있는 오픈뱅킹(Open Banking)은 고객 편의성과 데이터 활용에 극대화된 서비스 환경이다. 빠른 디지털 패러다임의 전환은 데이터 공유로 인한 정보유출, 해킹 등 보안 문제 역시 우려된다는 불안감도 증가시켰다. 이러한 부정적인 시각을 극복하지 못한다면 금융서비스 발전을 저해하는 요인이 될 것이다. 본 연구에서는 디지털 금융 생태계에서 데이터를 안전하고 포괄적 관리할 수 있는 보안 거버넌스 체계를 제시한다. 이는 오픈뱅킹 서비스 환경에 초점을 맞춰 현업 종사자들에게 디지털 금융보안 아키텍처를 제시함으로써 기술적 적용 방안을 마련한다. 금융 IT가 변화하는 환경에서 오픈뱅킹 서비스를 도입하고 활용할 수 있는 종합적 정보보호 체계를 제시함으로써 본 연구의 가치가 있다고 볼 수 있다.

• Archives of Plastic Surgery
• /
• 제48권5호
• /
• pp.473-482
• /
• 2021

Background The increasing number of bilateral breast cancer patients has been accompanied by a growing need for bilateral mastectomy with immediate reconstruction. However, little research has investigated the complications and aesthetic outcomes related to bilateral reconstruction. Therefore, we analyzed retrospective data comparing the outcomes of bilateral reconstruction using deep inferior epigastric perforator (DIEP) flaps or implants. Methods This study included 52 patients (24 DIEP group and 28 implant group) who underwent bilateral mastectomy with immediate reconstruction between 2010 and 2020. Patient demographics, surgical characteristics, and complications were recorded. The difference between the left and right position of the nipple-areolar complex with respect to the sternal notch point at the clavicle was measured, and breast symmetry was evaluated. Results The average weight of breasts reconstructed with DIEP flaps (417.43±152.50 g) was higher than that of breasts with implants. The hospitalization period and operation time were significantly longer in the DIEP group. Early complications were significantly more common in the implant group (36.53%) than in the DIEP group. The angles between the nipples and the horizontal line were 1.09°±0.71° and 1.75°±1.45° in the DIEP and implant groups, respectively. Conclusions Although the surgical burden is lower, breast reconstruction using implants requires greater attention with respect to implant positioning, asymmetry, and complications than DIEP flap reconstruction. DIEP flap reconstruction has a prolonged operation time and a high risk of flap failure, but yields excellent cosmetic results and does not require intensive follow-up. Patients should be consulted to determine the most suitable option for them.