• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.370-375
• /
• 2003

Optical fiber vibrations sensors (OFVSs) and extrinsic Fabry-Perot interferometer (EFPI) were used in damage monitoring of fiber-metal laminates(FML). The optical fiber vibration sensor and EFPI were applied in order to detect and evaluate the strain, damage and failure of FML. Damages in composites, such as matrix cracks, delamination and fiber breakage may occur as a result of excessive load, fatigue and low-velocity impacts. Tensile and indentation test was performed with the measurement of optical signal and acoustic emission (AE). The signals of the optical fiber vibration sensor due to damages were quantitatively evaluated by wavelet transform. It was found that damage information of comparable in quality to acoustic emission data could be obtained from the optical fiber vibration sensor signals.

• Journal of Sensor Science and Technology
• /
• v.29 no.1
• /
• pp.51-58
• /
• 2020

In this study, a novel method for sweeping automatic linearization of wavelength swept laser is proposed. Through the test performed on the implemented laser, the linear sweeping is held up well with a 97% decrease in nonlinearity, and 60 nm sweeping range, 1 kHz sweeping frequency, and 8.8 mW average optical power were obtained. The proposed method uses fiber Bragg grating array, optical-electronic conversion circuit, FPGA embedded module, and a LabVIEW program to generate new compensated wave patterns which were applied to the fiber Fabry-Perot tunable filter. Linear sweeping can reduce the cumbersome and time-consuming recalibration process required for nonlinear sweeping. Additionally, the proposed method provides more accurate measurement results for the structure safety monitoring system.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2003.04a
• /
• pp.42-45
• /
• 2003

Optical fiber vibrations sensors (OFVSs) and extrinsic Fabry-Perot interferometer (EFPI) were used in damage monitoring of fiber-metal laminates(FML). The optical fiber vibration sensor and EFPI were applied in order to detect and evaluate the strain, damage and failure of FML. Damages in composites, such as matrix cracks, delamination and fiber breakage may occur as a result of excessive load, fatigue and low-velocity impacts. Indentation test was performed with the measurement of optical signal and acoustic emission (AE). The signals of the optical fiber vibration sensor due to damages were quantitatively evaluated by wavelet transform. It was found that damage information of comparable in quality to acoustic emission data could be obtained from the optical fiber vibration sensor signals.

• Journal of Sensor Science and Technology
• /
• v.14 no.5
• /
• pp.302-307
• /
• 2005

Precision displacement of less than a few nm resolution was measured in real-time using fiber optic EFPI sensor. The novel method for real-time processing of analyzing EFPI output signal was developed and verified. Linearity in the mean values of interferometric light intensity among adjacent fringes was shown and verified the sinusoidal approximation algorithm that estimates past and coming fringe values. Real-time signal processing program was developed and the intensity signal of the EFPI sensor was transformed to the phase shift with this program. The resolution below $0.36{\sim}8.6$ nm in the displacement range of $0{\sim}300{\mu}m$ was obtained. The nano-positioner with a piezoelectric actuator and the EFPI sensor system was designed and tested. The positioner successfully reached to the desired destination within 1 nm accuracy.

• Journal of Sensor Science and Technology
• /
• v.28 no.3
• /
• pp.171-176
• /
• 2019

The biomarkers related to the colorectal cancers and diseases were surveyed and summarized, and an optical electronic nose was researched and developed for their analysis. The prototyped sensor revealed that it could discriminate two gases: ethanol 2000 ppm and $CO_2$ 500 ppm. Furthermore, the sensor demonstrated the potential capability of estimation of $CO_2$ concentration with 95% confidence level. Based on the above experimental results, the developed optical electronic nose was tested with the mixtures of gases (Isopropyl Alcohol, Acetone, Methanol, and Toluene) and the biomarkers were successfully segregated using principal component analysis.

• Composites Research
• /
• v.14 no.6
• /
• pp.47-58
• /
• 2001

This paper describes applications of cure monitoring techniques by using embedded fiber optic strain sensors, which are extrinsic Fabry-Perot interoferometric (EFPI) and/or fiber Bra99 grating (FBG) sensors, to three kinds of molding methods of autoclave, FW and RTM molding methods. In these applications, internal strain of high-temperature curing resin was monitored by EFPI sensors. From theme experimental results, it was shown that strain caused by thermal shrink at cooling stage could be measured well. In addition, several specific matters to these molding methods were considered. As thor an autoclave molding of unidirectional FRP laminates, it was confirmed that off-axis strain of unidirectional FRP could be monitored by EFPI sensors. As for FW molding using room-temperature (RT) cured resin, it was found that the strain outputs from EFPI sensors represented curing shrinkage as well as thermal strain and the convergence meant finish of cure reaction. It was also shown that this curing shrinkage should be evaluated with consideration on logarithmic change in stiffness of matrix resin. As for a RTM melding, both EFPI and FBC sensors were employed to measure strain. The results showed that FBG sensors hale also good potential for strain monitoring at cooling stage, while the non-uniform thermal residual strain of textile affected the FBG spectrum after molding. This study has proven that embedded fiber optic strain sensors hale practical ability of cure monitoring of FRP. However, development of automatic installation methods of sensors remains as a problem to be solved for applications to practical products.

• Korean Journal of Optics and Photonics
• /
• v.6 no.4
• /
• pp.365-372
• /
• 1995

A signal processing technique for interferometric fiber-optic sensors is proposed. It does not require a any special optic components such as phase modulator, $3times3$ couplers,to obtain the full sensitivity of the interferometer. Instead, it requires a reference interferometer for phase referencing and a reference mirror for intensity referencing, but intensity referencing can be done without using the r reference mirror. The new technique utilizes the frequency chirping of the laser diode to process t the sensor signal with both wide dynamic range and high sensitivity of the interferometer. It was a applied to an internal-mirrored FP interferometric temperature sensor to obtain the system noise of $4\times10^{-3\circ}C$ from I cm FP Interferometor sensor device.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.32 no.5
• /
• pp.50-57
• /
• 2004

For the application of structural health monitoring such as AE detection, a stabilized FBG sensor system with wide dynamic range was proposed. A tunable Fabry-Perot filter with narrow free spectral range(FSR) was used to simplify the multiplexing demodulator for FBG vibration sensors. Stabilization controlling system was also developed for the maintenance of maximum sensitivity of the sensors. In order to verify the performance of the proposed FBG vibration sensor system, we measured sensitivity, and the system showed the average sensitivity of 256 $n{\in}_{mas}/{\sqrt{Hz}}$. Finally, multi-points vibration tests using in-line FBG sensors were conducted to validate the multiplexing performance of the FBG system.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.1
• /
• pp.49-55
• /
• 2002

In this paper, we present the simulation monitoring of strain and temperature during and after the cure of unsymmetric composite laminate using fiber optic sensors. Fiber Bragg grating/extrinsic Fabry-Perot interferometric (FBG/EFPI) hybrid sensors are used to measure those measurands. The characteristic matrix of the sensor is analytically derived and measurements can be done without sensor calibration. A wavelength-swept fiber laser is utilised as a lighr source. Two FBG/EFPI sensors are embedded in a graphite/epoxy unsymmetric cross-ply composite laminate in different directions and different locations. We perform a real time monitoring of fabrication strains and temperatures at two points of the composite laminate during cure process in an autoclave. Also, the thermal strains and temperatures of the fabricated laminate are measured in a thermal chamber. Through these experiments, we can provide a basis for the efficient smart processing of composite and know the thermal behavior of unsymmetric cross-ply composite laminate.

• Korean Journal of Optics and Photonics
• /
• v.20 no.3
• /
• pp.189-194
• /
• 2009

We demonstrate a ring type wavelength swept laser incorporating a fiber Fabry-Perot tunable filter in a laser cavity using 1300 nm semiconductor optical amplifier as a gain medium. The output characteristics of the wavelength swept laser according to the applied scanning frequencies are analyzed in the temporal and spectral domain. The output of the wavelength swept laser decreases dramatically as the scanning frequency increases. And there is a significant peak power imbalance between the forward scan and the backward scan as the scanning frequency increases. Its use in practical applications might be limited.