• 한국태양에너지학회 논문집
• /
• 제27권1호
• /
• pp.91-98
• /
• 2007

Perimeter zone is one of the weakest area in buildings and it makes an increase of heating and cooling loads, in addition to condensation or discomfort with cold-draft to residents in winter. Because of this, it needs to be reinforced by active systems. However, they use fossil fuel, and ultimately greenhouse effect is urged. Thus, we proposed BIPV system functioned as solar collector which can substitute active system. As an fundamental stage, heat balance equation in steady-state by Fortran was used not only, in winter for pre-heating effect and electric power capacity during the day, but also in summer, for the latter during the day and sky radiation effect during the night. Especially, we should have considered shading on PV by IES Suncast, since even a little bit of it makes the efficiency too low for the PV modules to work. As a result, in summer day, the PV panel should be tiled in 70 degrees to gain the most electric power. Moreover, we could verify that this model makes higher temperature and heat flux under 0.02 m/s. On the other hand, the PV had the high efficiency with high velocity because of cooling effect behind the PV. Therefore, we should regard the air current distribution later on.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2006년도 하계학술발표대회 논문집
• /
• pp.953-958
• /
• 2006

Perimeter zone has been reinforced by active systems, such as fan-coil units, because it causes an increase in heating and cooling loads, dew condensation in winter, or discomfort with cold-draft to residents in buildings, through poor insulation by light-weighed skin due to progressing multi-storied buildings and skyscrapers. However, because these active systems raise Its capacity so that fossil fuel is used as much as they are added, and ultimately, greenhouse effect is urged, we proposed BIPV system functioned as solar collector which can substitute active system. As an early stage, heat balance equation in steady-state by Fortran was used not only for pre-heating effect and electric power capacity during the day in winter, but also for electric power capacity during day in slimmer and sky radiation effect during night in summer. Especially, we should have considered shading on PV, since even a little bit of it makes the efficiency too low for the PV to work. Still, when the flux of pre-heated air was increased to make air-barrier, its temperature was not enough to make it because the speed of heat exchange was too fast to warm up the air, thus the capacity to meet the condition was evaluated, and electric power from PV was made used for it.

• Journal of Welding and Joining
• /
• 제15권1호
• /
• pp.92-100
• /
• 1997

손상된 ASTM A-470 class 8 고압 증기 터어빈 로터강의 수명 연장을 위해 보수 용접이 행하여졌다. SAW 용접부의 미세경도 측정결과 모재의 경도는 VHN 253이었으나 모재에 근접한 열영향부의 경도는 VHN 227로 떨어졌다. 이와 같이 경도가 떨어진 영역을 "연화층"이라 정의하였으며 약 0.5-0.6mm의 크기를 나타내었다. 한편 크립 파단 시험시 파괴는 연화층 부근에서 일어났으며 593.deg. C와 19Ksi(132 Mpa)에서 파단시간은 772.4hr이었다. 연화층의 크기를 줄이기 위해서 MIG 및 TIG 용접이 행하여졌는데 연화층 크기는 MIG의 경우 0.3-0.4mm이고, TIG의 경우에는 입열량의 크기에 따라 0부터 0.4mm의 크기를 나타내었다. 그러나 크립 파단시간은 연화층 크기가 작아질수록 감소하였다. 특히 TIG 용접부의 경우 크립 파단시간은 입열량과 밀접한 관계를 나타내었는데 입열량이 클수록 파단시간은 길어졌다. 대부분의 파괴는 ICHAZ에서 발생되었으나 입열량이 감소함에 따라 파단부는 CGHAZ으로 이동하였다. 파단면은 tearing과 dimple을 갖는 입내파괴를 나타내었다.파괴를 나타내었다.

• 자원환경지질
• /
• 제42권3호
• /
• pp.235-246
• /
• 2009

서천지역 금강하구둑 부근의 길산천 소유역에서 전기전도도 12,000${\sim}$21,000 $\mu$S/cm 의 고(高)염분 지하수가 산출된다. 이러한 고염분 지하수 대수층은 심도를 달리하는 2개 모래질 퇴적층과 1개 풍화대 및 부정합면으로 구성되어 었으며, 대수층 상호간에는 수리지질 및 수리지화학적으로 단절된 양상을 보인다. 연구지역에서 산출되는 고염분 지하수의 기원에 대하여 고찰해 보기 위해, 대수층의 산출 특성, 지하수의 수질 특성, 지하수위 및 전기전도도의 시계열 관측과 주기 분석이 검토되었다. 국내 서 남해안지역에서 해수의 영향을 받은 지하수 수질은 주로 현재 진행중인 해수침투 개념에 의해 설명되는 경향이었다. 하지만 이번 연구결과 길산천 소유역 하류지역에서 보이는 고(高)염분 지하수의 수질 및 산출 특성은 해수침투라는 역동적인 메카니즘에 의한 것이 아니라, 과거 지질시대의 조간대 퇴적물내 혹은 매립지내에 포켓상으로 고립 포획된 고(古)염분 성분에 의한 것으로 해석되었다.

• 대기
• /
• 제31권5호
• /
• pp.593-606
• /
• 2021

The Korea Meteorological Administration/National Institute of Meteorological Sciences (KMA/NIMS) has monitored atmospheric CO₂ at Anmyeondo (AMY) World Meteorological Organization (WMO) Global Atmosphere Watch Programme (GAW) regional station since 1999, and expanded its observations at Jeju Gosan Suwolbong station (JGS) in the South and at Ulleungdo-Dokdo stations in the East (ULD and DOK) since 2012. Due to a recent WMO CO₂ scale update and a new filter (NIMS) to select baseline levels at each station, the 22 years of CO₂ data are recalculated. After correction for the new CO₂ scale, we confirmed that those corrected records are reasonable within the compatibility goal (±0.1 ppm of CO₂) between KMA/NIMS and National Oceanic and Atmosphereic Administration (NOAA) flask-air measurements with the new scale. With the new NIMS filter, CO₂ baseline levels are now more representative of the large-scale background compared to previous values, which contained large CO₂ enhancements. Atmospheric CO₂ observed in South Korea is 4 to 8 ppm greater than the global average while the amplitude of seasonal variation is similar (10~13 ppm) to the amplitude averaged over a comparable latitude zone (30°N-60°N). Variations in CO₂ growth rate are also similar, increasing and decreasing similar to global values, as it reflects the net balance between terrestrial respiration and photosynthesis. In 2020, atmospheric CO₂ continued increasing despite the COVID-19 pandemic. Even though fossil emission was reduced (around -7% globally), we still emitted large amounts of anthropogenic CO₂. Overall, since CO₂ has large natural variations and its source was derived from not only fossil fuel but also biomass burning, the small fossil emission reduction could not affect the atmospheric level directly.

• KIEAE Journal
• /
• 제8권1호
• /
• pp.19-24
• /
• 2008

The wind-power among the new and renewable energies uses the wind, a limitless, clean and pure energy which is available at any place. It requires low installation cost compared to the generation of other renewable energies, and is easy to operate, and furthermore, can be automated for operation. Korea has been taking a great deal of interest in the development of renewable energy generating equipment, specifically wind power generation as the nation has a nearly total reliance on imported petroleum. A measuring poll 30m high was installed at a location with an altitude of 142m above the sea level in order to measure and analyze the wind power potentiality at H University's Asan Campus, and the wind velocity and wind direction were measured for 1 year. As for the wind power resource of the area adjacent to Asan campus, the Weibull Distribution coefficient was C=2.68, K =1.29 at H30m. Weibull Distribution coefficient was modified on the basis of compensated wind velocity (=3.1m/s) at H 60m, and the energy density was $42W/m^2$. AEP 223,750 KWh was forecast based on the simulation of an 800KW grade wind turbine. It is considered that the wind power generation has to be studied further in the inland zone with low wind velocity to cope with the possible exhaustion of fossil fuel and ensure a sustainable environmental preservation.

• 보존과학회지
• /
• 제1권1호
• /
• pp.12-26
• /
• 1992

Ilsan peat-bed site, newly constructed city area, is located at the northern part of Seoul. This site is situated near the mouth of Han river, which flows through central Korea. Many fossil woods were excavated from this site, and surveyed the wood anatomical features. Totally 90 specimens were identified into 10 species including two roots and five barks which were not identified in detail. Alnus japonica and A. maxmowiczii are the most common and occupied 26. 7%, 34.4% of the total specimen number respectively, and then other species which excavated from Ilsan area are follows : Fraxinus rhynchophylla(18.9%), Lepido-balanus spp.(3.3%), Maackia amurensis(2.2%), Diospyros spp.(2.2%), Juglans mandshrica(1.1%), Prunophora spp.(1.1%), Malus or Pyrus spp.(1.1%), Rhamnus spp.(1.1%). Among the identified species there are fairly some species growing in the central - or northern temperate zone, such as A. maxmowiczii, F. rhynchophylla, Lepidobalanus spp., M. amurnsis, J. mandshurica, Rhumnus spp. Therefore, it can be estimated that the former temperature of Ilsan area was same or slightly cold than today. The species bearing fruit for food as .J, mandshunca, Diospyros spp., Prunophora spp., Mulus or Pyrus spp. were regarded as artificially planting trees, because they do not grow together in the same site.

• 대한기계학회논문집
• /
• 제13권3호
• /
• pp.547-553
• /
• 1989

본 연구에서는 작동유체로서 수증기와 거동이 유사한 습공기를 대기 흡입식 풍동을 사용하여 원호 노즐로서 팽창시키는 경우에 대하여 응축충격파가 발생하는 흐름이 측정부내에 쐐기를 설치하여 발생시킨 경사충격파에 미치는 영향에 대해 실험적으로 조사하였다.

• 한국해양학회지:바다
• /
• 제2권2호
• /
• pp.125-137
• /
• 1997

심해저 퇴적물중 금속과 희토류 원소의 수직 함량변화 및 변화의 원인을 구명하기 위해 북동태평양 클라리온-클리퍼톤 균열대(Clarion-Clipperton fracture zone) 중남부에 위치한 한국심해환경연구(Korea Deep-sea Environmental Study, KODES) 지역에서 박스코어러(box corer)를 이용해 18개의 주상시료를 채취했다. KODES 지역 퇴적층은 색상변화에 따라 갈색의 Unit I, 연갈색의 Unit II, 흑(갈)색의 Unit III로 분류된다. Unit I은 Unit II에 비해 높은 Ni/Cu비를 가지고, Unit III는 Unit I, II에 비해 현저히 높은 금속함량을 보인다. Unit II는 지화학적 자료에 근거하여 상부의 Unit IIa 층과 하부의 Unit IIb 층으로 세분될 수 있는데, Unit IIb 층은 Unit IIa 층에 비해 높은 구리 및 3+REEs/NASC 비(또는 큰 음의 Ce 이상치) 등의 특징을 보인다. Unit III는 흑갈색의 상부 Unit IIIa 층과 흑색의 하부 Unit IIIb 층으로 세분되는데, Unit IIIb 층은 Unit IIIa 층에 비해 망간, 철 함량이 높다. 연구지역이 속한 태평양 지판의 확장속도와 방향 그리고 약 11-30 Ma 인 Unit III의 연령을 고려할 때 Unit IIIb 층은 동태평양 균열대(East Pacific Rise, EPR) 그리고 적도와 근접한 위치에서 퇴적된 것으로 계산된다. 흑색인 Unit IIIb 층의 높은 망간, 철 함량은 EPR에서 기원한 화산기원의 철, 망간 등을 공급받아 나타난 결과로 보인다. 한편, Unit III는 물론이고 Unit IIb 역시 적도 고생산대의 영향권에 있었고, 따라서 해수중 풍부한 유기체들과 함께 구리, 희토류 원소 등도 Unit IIb, III 층으로 많이 공급되었을 것이다. 퇴적물로 공급된 이들 구리 및 희토류 원소들은 유기물이 분해됨에 따라 스멕타이트 그리고 어류 잔해물(fish bone debris) 등에 잔류한 것으로 보인다. 즉 KODES 지역 주상 퇴적물에서 나타나는 구리 및 희토류 원소의 수직 함량변화는 연구지역이 제3기 말 시기에 적도 고생산대를 지나는 동안 많은 유기물을 공급받아서 초래된 결과로 사료된다.

• Structural Engineering and Mechanics
• /
• 제49권4호
• /
• pp.427-448
• /
• 2014

At present, the time of easy oil and gas is over. Now, the largest part of fossil fuels is concentrated in the deepest levels of tectonic structures and in the sea shelves. One of the most cumbersome operations of their extraction is the bore-hole drilling. In connection with austere tectonic and climate conditions, their drivage every so often is associated with great and diversified technological difficulties causing emergencies on frequent occasions. As a rule, they are linked with drill string accidents. A key role in prediction of these situations should play methods of theoretical modelling. For this reason, there is a growing need for development and implementation of new numerical methods for computer simulation of critical and post-critical behavior of drill strings (DSs). In this paper, the processes of non-linear deforming of a DS in cylindrical cavity of a deep bore-hole are considered. On the basis of the theory of curvilinear flexible rods, non-linear constitutive differential equations are deduced. The effects of the longitudinal non-uniform preloading, action of torque and interaction between the DS and the bore-hole surface are taken into account. Owing to the use of curvilinear coordinates in the constraining cylindrical surface and a specially chosen concomitant reference frame, it became possible to separate the desired variables and to reduce the total order of the equation system. To solve it, the method of continuation the solution by parameter and the transfer matrix technique are applied. As a result of the completed numerical analysis, the critical states of the DS loading in the cylindrical channels of inclined bore-holes are found. It is shown that the modes of the post-critical deforming of the DS are associated with its irregular spiral curving prevailing in the zone of bottom-hole-assembly. The possibility of invariant state generation during post-critical deforming is established, condition of its bifurcation is formulated. It is shown that infinite variety of loads can correspond to one geometrical configuration of the DS. They differ each from other by contact force functions.