• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 춘계학술대회 논문집
• /
• pp.248-251
• /
• 2009

AB100 & CB100 are general products in the steel beam of the section shape. They are applied for construction, welding and shipbuilding structures. But currently roll damages are generated in the intermediate & finish mills during producing AB 100, CB100. The goal of this project is to conduct rolling & roll stress analysis using the 3D FEM program and to research the things which roll diameter affects roll stress. By the analysis results, it is determined that the recording roll stress where the roll diameter will be big comes to be small, and it is recognized that roll damage occurrences of finish rolling mills can be high by roll stress analysis results.

• EDISON SW 활용 경진대회 논문집
• /
• 제5회(2016년)
• /
• pp.222-227
• /
• 2016

In this paper, the optimized design for bow structure was investigated by using EDISON software. Considering the mechanism of the bow, non-linear FEM analysis was essential. The factors of the design are height, width, number of holes and taper value. High performance of the internal energy and lowest mass were main issues. The limit of the von-mises stress was yield strength for the material. Material was chosen by considering typical bow material, Aluminum. Using Taguchi method($L_9$), 9 models were selected and contribution rate was calculated for each factors. Following the contribution rate, 3 factors were fixed and optimized model was predicted. After making optimized model for FEM analysis, the value of internal-energy, mass for FEM model were compared with predicted value, calculated the percentage error and figure out the reliability of Taguchi method.

• 한국산학기술학회논문지
• /
• 제15권10호
• /
• pp.5950-5954
• /
• 2014

본 논문의 목적은 설계 변경된 세척기의 유한요소해석에 있으며 세척 성능을 향상시킨 세척기 개발을 위하여 기존 세척기의 구조를 변경하여 설계하였다. 설계 시 프로그램은 CATIA V5를 사용하였으며 유한요소해석에 필요한 모델링 또한 CATIA V5를 사용하였다. 모델링된 세척기에 대하여 3차원 유한요소해석 프로그램인 ANSYS를 사용하여 해석을 수행하였으며 안정성을 검증하기 위하여 내부압력의 변화에 따른 유체의 흐름을 구하였다. 이러한 해석결과는 새로운 모델의 세척기를 개발하는데 활용되었다.

• 대한금속재료학회지
• /
• 제49권6호
• /
• pp.468-473
• /
• 2011

Determining the residual stress during casting processes is important for evaluating the mechanical properties and strength of materials and to optimize manufacturing conditions. In this study, we propose a field data interface procedure between FDM and FEM in a 3-dimensional space for analyzing the casting process and structural analysis. The casting process was analyzed using FDM and the data of the temperature distribution were converted into a format suitable for FEM analysis to calculate the thermal stress and safety factor by tightening force. The results of the coupled analysis between FDM and FEM showed that casting residual stress is an important factor in predicting life time and evaluating durability.

• Geomechanics and Engineering
• /
• 제9권4호
• /
• pp.415-426
• /
• 2015

Researches have been done to discover ways to strengthen peat soil deposits. In this model study, fibrous peat that is the most compressible types of peat has been reinforced with precast peat columns stabilized with ordinary Portland cement and polypropylene fibres. Rowe cell consolidation tests as well as plate load tests (PLTs) were conducted on various types of test samples to evaluate the strength and deformation of untreated peat and peat reinforced by various types of columns. PLTs were conducted in a specially designed and fabricated circular steel test tank. The compression index ($C_c$) and recompression index ($C_r$) of fibrous peat samples reduced considerably upon use of precast columns. Also, PLT results confirmed the results obtained from Rowe cell tests. Use of polypropylene fibres added to cement further decreased ($C_c$) and ($C_r$) and increased load bearing capacity of untreated peat. Finite element method (FEM) using Plaxis 3D was carried out to evaluate the stress distributions along various types of tested samples and also, to compare the deformations obtained from FEM analysis with the actual maximum deformations found from PLTs. FEM results indicate that most of the induced stresses are taken on the upper portion of tested samples and reach their maximum values below the loading plate. Also, a close agreement was found between actual deformation values obtained from PLTs and values resulted from FEM analysis for various types of tested samples.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2003년도 추계학술대회논문집
• /
• pp.840-840
• /
• 2003

Operational Modal Analysis (OMA) is a technique for identification of modal parameters by measurement of only the system's response. On many lightweight structures, such as load-speaker cones and disk drive read/write heads, is impossible or impractical to measure the input forces. Another characteristic of lightweight structure is their sensitivity to mass loading from sensors. The Scanning Laser Doppler Vibrometry(SLDV) allows response measurements to be taken without mass loading. One disadvantage of OMA testing compared to tradition input output modal testing is the OMA mode shapes are un-scaled. This means that the mode shape obtained from an OMA test can not used for analytical structural modification studies. However, the un-scaled mode shapes from an OMA test can be used to update a Finite Element Model (FEM). The updated FEM can then be used to analytically predict the effect of structural modifications. This paper will present the results of an OMA test performed on a simple plate and motor in operating conditions. The un-scaled mode shapes from this test will be used to update a FEM model of the system. The updated FEM model will be then be used to predict the effect of attaching a mass to the plate. The shapes predicted by the FEM for the modified system will be compared to a second OMA test on the modified system

• The Journal of the Acoustical Society of Korea
• /
• 제21권3E호
• /
• pp.112-118
• /
• 2002

An unconstrained tuning fork with a 3-D model has been numerically analyzed by Finite Element Method (FEM) and Boundary Element Method (BEM). The first three natural frequencies were calculated by the FEM modal analysis. Then the trend of the change of the modal frequencies was examined with the variation of the tuning fork length and width. An formula for the natural frequencies-tuning fork length relationship were derived from the numerical analysis results. Finally the BEM was used for the sound pressure field calculation from the structural displacement data.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.486-490
• /
• 1997

Composite materials have varios complicated characteristics to the ply materials, ply orientations, ply stacking sequences and boundary conditions. Therefore, it is difficult to analysis composite materials. For efficient use of composite materials in engineering applications the dynamic behavior, that is, natural frequencies, nodal patterns should be informed. This study presents the experimental and FEM results for the free vibration of symmetrically and antisymmetrically laminated composite and hybrid composite rectangular plates. In order to demonstrate the validity of the experiment, FEM analysis using ANSYS was performed and natural frequencies experimentally obtined is compared with that calculated by FEM analysis. The results obtained from both experiment and FEM analysis show a good agreement.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1999년도 제3회 압연심포지엄 논문집 압연기술의 미래개척 (Exploitation of Future Rolling Technologies)
• /
• pp.88-97
• /
• 1999

In this study, a systematic approach for roll pass design in bar rolling was studied. To minimize the trial and errors in the process design, a roll CAD system and a FE analysis system were combined. Based on the system, a methodology for roll pass design by FEM was studied. At first, designed process was compared with the FE analysis results and process redesign based on the FEM results was performed to obtain the specified final geometry. Then, empirical formula for roll speed set-up was compared with the FE analysis results. Further study on various simulations for bar rolling will help in making up for the inaccuracy in the currently used empirical roll speed rules. In addition, verification of the accuracy of the FE analysis system must be performed using experimental data in the industry.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제48권6호
• /
• pp.316-321
• /
• 1999

Disk type single phase switched reluctance motor which is a simple robust construction, simple control circuit and low manufacturing cost, has a characteristics of axial and radial flux machines. However, because this DSPSRM has a complicated magnetic circuit, it is difficult to analyze the design characteristics.. In this study, the calculation of design parameter based on the conventional design theory of electric machine and the characteristics analysis by computer simulation was performed. As the DSPSRM has the characteristics of both AFM and RFM, it is difficult to analyze its characteristics by the 2D FEM. 3D FEM was applied in the analysis of energy distribution and approximated calculation of torque characteristics with rotor positions. With analysis results, prototype of DSPSRM is manufactured.