• 한국재료학회지
• /
• 제14권6호
• /
• pp.436-442
• /
• 2004

Elastic and plastic deformation behaviors of the high purity aluminum and the silica glass were studied using nanoindentation and finite element analysis(FEA) techniques. Berkovich- and cone-type indenters were used for the nanoindentation test. Deformation behaviors and nanoindent profiles of elastic, elastic-plastic or plastic materials were clearly visualized by FEA simulation. Effects of the penetration depth and strain hardening on the deformation behavior were examined. Pile-up and sink-in behaviors were studied by using FEA technique. Degree of pile-up or sink-in was found to be a function of the ratio of elastic modulus to yield strength of materials. FEA was found to be an effective method to study deformation behaviors of materials under nanoindentation, especially in the case when pile-up or sink-in phenomena occurred.

• Journal of Periodontal and Implant Science
• /
• 제45권1호
• /
• pp.8-13
• /
• 2015

Purpose: The aim of this study was to evaluate the transfer of different occlusal forces in various skeletal malocclusions using finite element analysis (FEA). Methods: Three representative human cone-beam computed tomography (CBCT) images of three skeletal malocclusions were obtained from the Department of Orthodontics, Yonsei University Dental Hospital, Seoul, South Korea. The CBCT scans were read into the visualization software after separating bones and muscles by uploading the CBCT images into Mimics (Materialise). Two separate three-dimensional (3D) files were exported to visualize the solid morphology of skeletal outlines without considering the inner structures. Individual dental impressions were taken and stone models were scanned with a 3D scanner. These images were integrated and occlusal motions were simulated. Displacement and Von Mises stress were measured at the nodes of the FEA models. The displacement and stress distribution were analyzed. FEA was performed to obtain the 3D deformation of the mandibles under loads of 100, 150, 200, and 225 kg. Results: The distortion in all three skeletal malocclusions was comparable. Greater forces resulted in observing more distortion in FEA. Conclusions: Further studies are warranted to fully evaluate the impact of skeletal malocclusion on masticatory performance using information on muscle attachment and 3D temporomandibular joint movements.

• Structural Engineering and Mechanics
• /
• 제36권5호
• /
• pp.545-560
• /
• 2010

Two or more distinct materials are combined into a single functionally graded material (FGM) where the microstructural composition and properties change gradually. Thermal post-buckling behavior of uniform slender FGM beams is investigated independently using the classical Rayleigh-Ritz (RR) formulation and the versatile Finite Element Analysis (FEA) formulation developed in this paper. The von-Karman strain-displacement relations are used to account for moderately large deflections of FGM beams. Bending-extension coupling arising due to heterogeneity of material through the thickness is included. Simply supported and clamped beams with axially immovable ends are considered in the present study. Post-buckling load versus deflection curves and buckled mode shapes obtained from both the RR and FEA formulations for different volume fraction exponents show an excellent agreement with the available literature results for simply supported ends. Response of the FGM beam with clamped ends is studied for the first time and the results from both the RR and FEA formulations show a very good agreement. Though the response of the FGM beam could have been studied more accurately by FEA formulation alone, the authors aim to apply the RR formulation is to find an approximate closed form post-buckling solutions for the FGM beams. Further, the use of the RR formulation clearly demonstrates the effect of bending-extension coupling on the post-buckling response of the FGM beams.

• 화약ㆍ발파
• /
• 제37권2호
• /
• pp.1-13
• /
• 2019

본 연구에서는 도심지 발파에서 형성되는 분할 단면의 변형을 확인하기 위해 Visual FEA 유한요소 프로그램으로 발파 단면을 모델링하여 발파 기폭 패턴에 따른 최대주변형률을 분석하였고, Visual FEA 유한요소 프로그램으로 분석된 분할 단면과 현장 발파로 형성된 분할 단면을 비교하였다. 결과적으로, 발파 기폭 패턴에 따라 분할 단면에서 최대주변형률의 차이를 나타냈고, 전산해석과 현장 발파에서 분할 단면이 유사한 파형 형태를 보이는 것으로 확인되었다.

• Geomechanics and Engineering
• /
• 제17권4호
• /
• pp.317-322
• /
• 2019

This paper presents the results of parametric analyses to compute the axial capacity of a suction pile using 2D and 3D finite element approaches. The study is intended to simplify the process of analyzing suction piles from 3D to 2D model. The research focuses on obtaining the coefficient to be applied into the 2D model in order to obtain results that are as close as possible to the 3D model. Two 2D models were used in the analysis, namely the plane strain and axisymmetric models. The analyses were performed using two actual offshore soil data of the North and West Java Indonesia. The study reveals that the simplification of model through 2D Finite Element is achievable by applying the appropriate coefficient to the stiffness parameters. The results show that the simplified model of the 2D FEA provides more conservative results (with the difference between 2% to 7%) than the 3D FEA.

• Steel and Composite Structures
• /
• 제46권3호
• /
• pp.353-366
• /
• 2023

This paper presents a finite-element analysis (FEA) of aluminum alloy rectangular hollow sections (RHSs) and square hollow sections (SHSs) with circular through-openings under three-point and four-point bending. First, a finite-element model (FEM) was developed and validated against the corresponding test results available in the literature. Next, using the validated FE models, a parametric study comprising 180 FE models was conducted. The cross-section width-to-thickness ratio (b/t) ranged from 2 to 5, the hole size ratio (d/h) ranged from 0.2 to 0.8 and the quantity of holes (n) ranged from 2 to 6, respectively. Third, results obtained from laboratory test and FEA were compared with current design strengths calculated in accordance with the North American Specifications (NAS), the modified direct strength method (DSM) and the modified Continuous strength method (CSM). The comparison shows that the modified CSM are conservative by 15% on average for aluminum alloy RHSs and SHSs with circular through-openings subject to bending. Finally, a new design equation is proposed based on the modified CSM after being validated with results obtained from laboratory test and FEA. The proposed design equation can provide accurate predictions of flexural capacities for aluminum alloy RHSs and SHSs with circular through-openings.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• 제5B권1호
• /
• pp.39-42
• /
• 2005

Though full 3D analysis is the proper method to analyze the hybrid stepping motor (HSM), it has weak points in the areas of computation time and complexity. This paper introduces 2D FEA using a virtual magnetic barrier for the axial cross section to save computation time. For the purpose of 2D FEA, the virtual magnetic barrier and equivalent permanent magnet model of HSM are proposed. This result is compared with that of experimental and 3D analysis, considered as a reference result.

• 한국기계가공학회지
• /
• 제14권2호
• /
• pp.121-126
• /
• 2015

In this research, a tool was developed for the rapid performance of three-dimensional finite element analysis (3D FEA) of a machine tool spindle system made of a shaft and bearings. It runs the FEA with data, such as the bearing stiffness and the coordinates of the points, to define the section of the shaft, bearing positions, and cutting point. developed for the spindle system and then implemented with the tool using an object-oriented programing technique that allows the use of the objects of the CAD system used in this research. Graphic user interfaces were designed for a user to interact with the tool. It provides rapid evaluation of the design of a spindle system, and therefore, it would be helpful to identify a near optimal design of a spindle system based on, say, static stiffness with design changes and, consequently, FEA.

• 한국생산제조학회지
• /
• 제24권2호
• /
• pp.172-176
• /
• 2015

In this research, a tool was developed to automate one-dimensional finite element analysis (1D FEA) for design of a machine tool spindle. Based on object-oriented programing, this tool employs the objects of a CAD system to construct a geometric model and then to convert it into the FE model of 1D beams at the workbenches of the CAD system with minimum data to define the spindle such as bearing positions and cross-sections of the shaft. Graphic user interfaces were developed for users to interact with the tool. This tool is helpful in identifying a near optimal design of the spindle with the automation of the FEA process with numerous design changes in minimum time and efforts. It is also expected to allow even design engineers to perform the FEA in search of an optimal design of the machine tool spindle.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2001년도 가을 학술발표회 논문집
• /
• pp.193-200
• /
• 2001

In this study, the methodology to develop a data model for steel box girder bridge based on STEP part 104 is presented. The concept of STEP and the schema of part 104 are briefly reviewed, and then the procedure of data model standardization is described. A new data model for steel box girder bridge is developed by incorporating with not only the geometric and topological representation schema of the part 42 but also the representation structure information of the part 43 and the detailed finite element analysis information of the part 104. The prototype of integrated finite element analysis(FEA) system by interfacing STEP physical file is also presented. The applicability of developed data model for FEA is verified by preprocessor system of FEA.